aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
diff options
context:
space:
mode:
authorSven Eckelmann <sven@narfation.org>2020-11-23 13:41:34 +0100
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>2021-01-19 15:39:36 +0100
commit4b35999588ee6dbe1fd818760b358b1191ddd0be (patch)
treea2b48984f37e6fc8daf06631e7d4f915fc37f8aa /target/linux/ath79
parent0fda8049a7d1fb34074b7d5e8041312c1971f87d (diff)
downloadupstream-4b35999588ee6dbe1fd818760b358b1191ddd0be.tar.gz
upstream-4b35999588ee6dbe1fd818760b358b1191ddd0be.tar.bz2
upstream-4b35999588ee6dbe1fd818760b358b1191ddd0be.zip
ath79: Add support for OpenMesh MR600 v1
Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 4x GPIO-LEDs (2x wifi, 1x wps, 1x power) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 1x ethernet - AR8035 ethernet PHY (RGMII) - 10/100/1000 Mbps Ethernet - 802.3af POE - used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> [rebase, make WLAN LEDs consistent, add LED migration] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79')
-rw-r--r--target/linux/ath79/dts/ar9344_openmesh_mr600-v1.dts46
-rw-r--r--target/linux/ath79/dts/ar9344_openmesh_mr600.dtsi133
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom3
-rw-r--r--target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration3
-rw-r--r--target/linux/ath79/generic/base-files/lib/upgrade/platform.sh1
-rw-r--r--target/linux/ath79/image/generic.mk20
7 files changed, 207 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/ar9344_openmesh_mr600-v1.dts b/target/linux/ath79/dts/ar9344_openmesh_mr600-v1.dts
new file mode 100644
index 0000000000..6c20f2715f
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_openmesh_mr600-v1.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344_openmesh_mr600.dtsi"
+
+/ {
+ compatible = "openmesh,mr600-v1", "qca,ar9344";
+ model = "OpenMesh MR600 v1";
+
+ aliases {
+ led-boot = &led_power_orange;
+ led-failsafe = &led_power_orange;
+ led-running = &led_power_orange;
+ led-upgrade = &led_power_orange;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi5g_green {
+ label = "green:wifi5g";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wps_blue {
+ label = "blue:wps";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_orange: power_orange {
+ label = "orange:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+
+ leds-ath9k {
+ compatible = "gpio-leds";
+
+ wifi2g {
+ label = "blue:wifi2g";
+ gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
diff --git a/target/linux/ath79/dts/ar9344_openmesh_mr600.dtsi b/target/linux/ath79/dts/ar9344_openmesh_mr600.dtsi
new file mode 100644
index 0000000000..987a32e344
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_openmesh_mr600.dtsi
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ serial0 = &uart;
+ label-mac-device = &eth0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x060000>;
+ read-only;
+ };
+
+ partition@b0000 {
+ label = "inactive";
+ reg = <0x0b0000 0x7a0000>;
+ };
+
+ partition@850000 {
+ label = "inactive2";
+ reg = <0x850000 0x7a0000>;
+ };
+
+ art: partition@ff0000 {
+ label = "ART";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0x1>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ pll-data = <0x06000000 0x00000101 0x00001313>;
+
+ mtd-mac-address = <&art 0x0>;
+
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-gmac0 = <1>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi@0,0 {
+ compatible = "pci168c,0030";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <8>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index fbe2545adb..df0842fc63 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -46,6 +46,7 @@ ath79_setup_interfaces()
netgear,ex7300|\
ocedo,koala|\
ocedo,raccoon|\
+ openmesh,mr600-v1|\
pcs,cap324|\
pisen,ts-d084|\
pisen,wmb001n|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 95ad2a57ef..150c70d68b 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -120,6 +120,9 @@ case "$FIRMWARE" in
ubnt,rocket-m)
caldata_extract "art" 0x1000 0x1000
;;
+ openmesh,mr600-v1)
+ caldata_extract "ART" 0x5000 0x440
+ ;;
wd,mynet-n750)
caldata_extract "art" 0x5000 0x440
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
index 231afd9f57..871d84ed63 100644
--- a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
+++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
@@ -17,6 +17,9 @@ engenius,epg5000)
glinet,gl-mifi)
migrate_leds ":net=:3g4g"
;;
+openmesh,mr600-v1)
+ migrate_leds ":wlan58=:wifi5g"
+ ;;
pcs,cap324)
migrate_leds "lan:amber=amber:lan" "lan:green=green:lan"
;;
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 79e023482b..81dd911564 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -50,6 +50,7 @@ platform_do_upgrade() {
jjplus,ja76pf2)
redboot_fis_do_upgrade "$1" linux
;;
+ openmesh,mr600-v1|\
openmesh,om2p-v2|\
openmesh,om2p-v4|\
openmesh,om2p-hs-v1|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index ccc9ff2ac2..14546f6ade 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1525,6 +1525,26 @@ define Device/ocedo_ursus
endef
TARGET_DEVICES += ocedo_ursus
+define Device/openmesh_mr600-common
+ SOC := ar9344
+ DEVICE_VENDOR := OpenMesh
+ DEVICE_MODEL := MR600
+ DEVICE_PACKAGES := uboot-envtools
+ IMAGE_SIZE := 7808k
+ BLOCKSIZE := 64k
+ KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
+ pad-to $$(BLOCKSIZE)
+ IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
+ openmesh-image ce_type=MR600 | append-metadata
+endef
+
+define Device/openmesh_mr600-v1
+ $(Device/openmesh_mr600-common)
+ DEVICE_VARIANT := v1
+ SUPPORTED_DEVICES += mr600
+endef
+TARGET_DEVICES += openmesh_mr600-v1
+
define Device/openmesh_om2p-common
DEVICE_VENDOR := OpenMesh
DEVICE_PACKAGES := uboot-envtools