aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
diff options
context:
space:
mode:
authorMichael Pratt <mcpratt@pm.me>2020-09-15 13:44:39 -0400
committerPetr Štetiar <ynezz@true.cz>2020-12-25 10:38:13 +0100
commit4a55ef639dabed9546003f37948b772fd5024292 (patch)
treede505a39a793272bac90832d99230c561bf1ebc2 /target/linux/ath79
parent57e6f3ae65e1e77db6291f29b40002646b76db3b (diff)
downloadupstream-4a55ef639dabed9546003f37948b772fd5024292.tar.gz
upstream-4a55ef639dabed9546003f37948b772fd5024292.tar.bz2
upstream-4a55ef639dabed9546003f37948b772fd5024292.zip
ath79: add support for Senao Engenius ECB600
FCC ID: A8J-ECB600 Engenius ECB600 is a wireless access point with 1 gigabit PoE ethernet port, dual-band wireless, external ethernet switch, and 4 external antennas. Specification: - AR9344 SOC (5 GHz, 2x2, WMAC) - AR9382 WLAN (2.4 GHz, 2x2, PCIe on-board) - AR8035-A switch (GbE with 802.3af PoE) - 40 MHz reference clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16DG - UART at H1 (populated) - 4 LEDs, 1 button (power, eth, 2.4 GHz, 5 GHz) (reset) - 4 external antennas MAC addresses: MAC addresses are labeled MAC1 and MAC2 The MAC address in flash is not on the label The OEM software reports these MACs for the ifconfig phy1 MAC 1 *:52 --- (2.4 GHz) phy0 MAC 2 *:53 --- (5 GHz) eth0 ----- *:54 art 0x0 Installation: 2 ways to flash factory.bin from OEM: - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Upgrade Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fdf0000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade Format of OEM firmware image: The OEM software of ECB600 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-senao-ecb600-uImage-lzma.bin openwrt-senao-ecb600-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh Later models in the ECB series likely have a different platform and the upgrade and image verification process differs. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035-A switch between the SOC and the ethernet PHY chips. For AR934x series, the PLL register for GMAC0 can be seen in the DTSI as 0x2c. Therefore the PLL register can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. Unfortunately uboot did not have the best values so they were taken from other similar DTS files. Tested from master, all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
Diffstat (limited to 'target/linux/ath79')
-rw-r--r--target/linux/ath79/dts/ar9344_engenius_ecb600.dts203
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom9
-rw-r--r--target/linux/ath79/image/generic.mk10
4 files changed, 219 insertions, 4 deletions
diff --git a/target/linux/ath79/dts/ar9344_engenius_ecb600.dts b/target/linux/ath79/dts/ar9344_engenius_ecb600.dts
new file mode 100644
index 0000000000..8f838607cc
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_engenius_ecb600.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "EnGenius ECB600";
+ compatible = "engenius,ecb600", "qca,ar9344";
+
+ aliases {
+ label-mac-device = &eth0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ serial0 = &uart;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "amber:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wifi5g {
+ label = "blue:wifi5g";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ ath9k-leds {
+ compatible = "gpio-leds";
+
+ wifi2g {
+ label = "blue:wifi2g";
+ gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+
+ devices = <&firmware1 &firmware2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "openwrt,okli";
+ label = "firmware";
+ reg = <0x0 0x0>;
+ };
+ };
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x050000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "loader";
+ reg = <0x0a0000 0x010000>;
+ read-only;
+ };
+
+ firmware2: partition@b0000 {
+ label = "firmware2";
+ reg = <0x0b0000 0x170000>;
+ };
+
+ partition@220000 {
+ label = "fakeroot";
+ reg = <0x220000 0x010000>;
+ read-only;
+ };
+
+ firmware1: partition@230000 {
+ label = "firmware1";
+ reg = <0x230000 0xbc0000>;
+ };
+
+ partition@df0000 {
+ label = "failsafe";
+ reg = <0xdf0000 0x200000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+
+ pll-data = <0x02000000 0x00000101 0x00001313>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-gmac0 = <1>;
+ rxdv-delay = <3>;
+ rxd-delay = <3>;
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi@0,0,0 {
+ compatible = "pci168c,0030";
+ reg = <0x0 0 0 0 0>;
+ qca,no-eeprom;
+ qca,disable-5ghz;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <(-2)>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ qca,disable-2ghz;
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <(-1)>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 3ea0815ff2..a3b5d45ad2 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -32,6 +32,7 @@ ath79_setup_interfaces()
engenius,ecb1200|\
engenius,ecb1750|\
engenius,ecb350-v1|\
+ engenius,ecb600|\
enterasys,ws-ap3705i|\
glinet,gl-ar300m-lite|\
glinet,gl-usb150|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 2746cf4137..867a1dac44 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -88,10 +88,7 @@ case "$FIRMWARE" in
caldata_extract "art" 0x5000 0x440
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1)
;;
- enterasys,ws-ap3705i)
- caldata_extract "calibrate" 0x5000 0x440
- ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR0)
- ;;
+ engenius,ecb600|\
mercury,mw4530r-v1|\
ocedo,raccoon|\
tplink,tl-wdr3500-v1|\
@@ -104,6 +101,10 @@ case "$FIRMWARE" in
winchannel,wb2000)
caldata_extract "art" 0x5000 0x440
;;
+ enterasys,ws-ap3705i)
+ caldata_extract "calibrate" 0x5000 0x440
+ ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR0)
+ ;;
netgear,wnr2200-8m|\
netgear,wnr2200-16m|\
pcs,cap324|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index ec2b1d2bde..064177fcaf 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1002,6 +1002,16 @@ define Device/engenius_ecb350-v1
endef
TARGET_DEVICES += engenius_ecb350-v1
+define Device/engenius_ecb600
+ $(Device/engenius_loader_okli)
+ SOC := ar9344
+ DEVICE_MODEL := ECB600
+ IMAGE_SIZE := 12032k
+ LOADER_FLASH_OFFS := 0x230000
+ ENGENIUS_IMGNAME := senao-ecb600
+endef
+TARGET_DEVICES += engenius_ecb600
+
define Device/engenius_enh202-v1
$(Device/engenius_loader_okli)
SOC := ar7240