aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
diff options
context:
space:
mode:
authorSven Eckelmann <sven@narfation.org>2020-11-23 13:41:34 +0100
committerHauke Mehrtens <hauke@hauke-m.de>2022-01-16 20:51:14 +0100
commit1699c1dc7f26b332f868d338457abfbe716d6ba0 (patch)
treec8524b6a9bb6d34fe0dc9b8ea5b9f763b844ca17 /target/linux/ath79
parent7e484b902d269d8fd22afeccb765ccc2cd8efa19 (diff)
downloadupstream-1699c1dc7f26b332f868d338457abfbe716d6ba0.tar.gz
upstream-1699c1dc7f26b332f868d338457abfbe716d6ba0.tar.bz2
upstream-1699c1dc7f26b332f868d338457abfbe716d6ba0.zip
ath79: Add support for OpenMesh OM5P-AC v2
Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
Diffstat (limited to 'target/linux/ath79')
-rw-r--r--target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts139
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata7
-rw-r--r--target/linux/ath79/generic/base-files/lib/upgrade/platform.sh1
-rw-r--r--target/linux/ath79/image/generic.mk6
4 files changed, 120 insertions, 33 deletions
diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts
index b4d452dda1..91a53343ae 100644
--- a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts
+++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts
@@ -7,26 +7,34 @@
/ {
compatible = "openmesh,om5p-ac-v2", "qca,qca9558";
- model = "OpenMesh OM5P-AC V2";
+ model = "OpenMesh OM5P-AC v2";
- extosc: ref {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-output-names = "ref";
- clock-frequency = <40000000>;
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ label-mac-device = &eth0;
};
leds {
compatible = "gpio-leds";
- power {
- label = "blue:power";
- gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- };
-
wifi_green {
label = "green:wifi";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
};
wifi_yellow {
@@ -50,6 +58,32 @@
};
};
+ i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH /* sda */
+ &gpio 18 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,sda-open-drain;
+
+ tmp423a@4e {
+ compatible = "ti,tmp423";
+ reg = <0x4e>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+
gpio-export {
compatible = "gpio-export";
#size-cells = <0>;
@@ -69,11 +103,11 @@
&pinmux {
pinmux_pa_dcdc_pins {
- pinctrl-single,bits = <0x0 0xff00 0x0>;
+ pinctrl-single,bits = <0x0 0x0 0xff0000>;
};
pinmux_pa_high_pins {
- pinctrl-single,bits = <0x10 0xff 0x0>;
+ pinctrl-single,bits = <0x10 0x0 0xff>;
};
};
@@ -81,10 +115,6 @@
status = "okay";
};
-&pll {
- clocks = <&extosc>;
-};
-
&spi {
status = "okay";
@@ -93,6 +123,7 @@
reg = <0>;
spi-max-frequency = <25000000>;
+ /* partitions are passed via bootloader */
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
@@ -104,19 +135,29 @@
read-only;
};
- partition@1 {
+ partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
- partition@2 {
- compatible = "denx,uimage";
- label = "firmware";
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x060000>;
+ read-only;
+ };
+
+ partition@b0000 {
+ label = "inactive";
+ reg = <0x0b0000 0x7a0000>;
+ };
+
+ partition@850000 {
+ label = "inactive2";
reg = <0x850000 0x7a0000>;
};
- partition@3 {
- label = "art";
+ art: partition@ff0000 {
+ label = "ART";
reg = <0xff0000 0x010000>;
read-only;
};
@@ -127,18 +168,25 @@
&mdio0 {
status = "okay";
+ phy-mask = <0x10>;
+
phy4: ethernet-phy@4 {
reg = <4>;
- phy-mode = "rgmii-id";
+ eee-broken-100tx;
+ eee-broken-1000t;
};
};
&mdio1 {
status = "okay";
+ phy-mask = <0x2>;
+
phy1: ethernet-phy@1 {
reg = <1>;
- phy-mode = "sgmii";
+ eee-broken-100tx;
+ eee-broken-1000t;
+ at803x-override-sgmii-link-check;
};
};
@@ -147,7 +195,20 @@
pll-data = <0x82000101 0x80000101 0x80001313>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+
+ phy-mode = "rgmii-id";
phy-handle = <&phy4>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-enabled = <1>;
+ rxd-delay = <2>;
+ rxdv-delay = <2>;
+ txd-delay = <0>;
+ txen-delay = <0>;
+ };
};
&eth1 {
@@ -155,5 +216,33 @@
pll-data = <0x03000101 0x80000101 0x80001313>;
+ nvmem-cells = <&macaddr_art_6>;
+ nvmem-cell-names = "mac-address";
+
+ qca955x-sgmii-fixup;
+
phy-handle = <&phy1>;
};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <2>;
+};
+
+&art {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_art_6: macaddr@6 {
+ reg = <0x6 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 6da323facc..109b33795a 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -105,12 +105,9 @@ case "$FIRMWARE" in
openmesh,a40|\
openmesh,a60|\
openmesh,mr1750-v1|\
- openmesh,mr1750-v2)
- caldata_extract "ART" 0x5000 0x844
- ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) 16)
- ;;
+ openmesh,mr1750-v2|\
openmesh,om5p-ac-v2)
- caldata_extract "art" 0x5000 0x844
+ caldata_extract "ART" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) 16)
;;
qihoo,c301)
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 3d953d7982..13b6ec9d99 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -82,6 +82,7 @@ platform_do_upgrade() {
openmesh,om2p-lc|\
openmesh,om5p|\
openmesh,om5p-ac-v1|\
+ openmesh,om5p-ac-v2|\
openmesh,om5p-an)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 2cd24ab67b..64efa28f84 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1926,12 +1926,12 @@ endef
TARGET_DEVICES += openmesh_om5p-ac-v1
define Device/openmesh_om5p-ac-v2
+ $(Device/openmesh_common_64k)
SOC := qca9558
- DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := OM5P-AC
DEVICE_VARIANT := v2
- DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
- IMAGE_SIZE := 7808k
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ OPENMESH_CE_TYPE := OM5PAC
SUPPORTED_DEVICES += om5p-acv2
endef
TARGET_DEVICES += openmesh_om5p-ac-v2