diff options
| author | Sven Eckelmann <sven@narfation.org> | 2020-11-23 13:41:34 +0100 |
|---|---|---|
| committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-12-28 19:37:24 +0100 |
| commit | dd1d95cb0357278900d09fae3ad20e9e0b2d569a (patch) | |
| tree | 40d6e7f6658fdcbd9fb0ae0f9b56867d59bad0ea /target/linux/ath79/generic/base-files/etc | |
| parent | e1938d3397ba2bc40d27dc4f97f8532228de6112 (diff) | |
| download | upstream-dd1d95cb0357278900d09fae3ad20e9e0b2d569a.tar.gz upstream-dd1d95cb0357278900d09fae3ad20e9e0b2d569a.tar.bz2 upstream-dd1d95cb0357278900d09fae3ad20e9e0b2d569a.zip | |
ath79: Add support for OpenMesh OM2P v4
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 1
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79/generic/base-files/etc')
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/01_leds | 4 | ||||
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/02_network | 1 |
2 files changed, 5 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 443cccce81..8095712e88 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -230,6 +230,10 @@ netgear,wnr2200-16m) ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "amber:lan3" "switch0" "0x08" "0x02" ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "amber:lan4" "switch0" "0x10" "0x02" ;; +openmesh,om2p-v4) + ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" + ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" + ;; pcs,cr3000) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 14e858b8fa..fa98b18e59 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -152,6 +152,7 @@ ath79_setup_interfaces() comfast,cf-e120a-v3|\ comfast,cf-e314n-v2|\ compex,wpj531-16m|\ + openmesh,om2p-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e|\ tplink,cpe210-v1|\ |