diff options
| author | Sander Vanheule <sander@svanheule.net> | 2020-07-26 22:40:54 +0200 |
|---|---|---|
| committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-09-12 19:37:24 +0200 |
| commit | c9f51a9ad6e8f99ed7adb78d208740b7d351985b (patch) | |
| tree | 2ac82f84c562304068d1345b16fca19dd468bde4 /target/linux/ath79/generic/base-files/etc/board.d/02_network | |
| parent | 53df30f02beab977991431c6f687f5ac5d88999c (diff) | |
| download | upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.tar.gz upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.tar.bz2 upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.zip | |
ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79/generic/base-files/etc/board.d/02_network')
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/02_network | 4 |
1 files changed, 4 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 0206e2360e..f437f7432f 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -302,6 +302,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5" ;; + tplink,eap225-wall-v2) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" + ;; tplink,eap245-v3) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:1" "5:lan:2" |