ath79: rename dts/image using manufacturer_board scheme

This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

1 files changed, 0 insertions, 124 deletions

diff --git a/target/linux/ath79/dts/ar9331_tl-wr703n_tl-mr10u.dtsi b/target/linux/ath79/dts/ar9331_tl-wr703n_tl-mr10u.dtsi
deleted file mode 100644
index d23dea7d92..0000000000
--- a/target/linux/ath79/dts/ar9331_tl-wr703n_tl-mr10u.dtsi
+++ /dev/null
@@ -1,124 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "ar9331.dtsi"
-
-/ {
-	aliases {
-		serial0 = &uart;
-		led-status = &led_system;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		poll-interval = <20>;
-
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-	};
-	
-	gpio-leds {
-		compatible = "gpio-leds";
-
-		led_system: system {
-			label = "tl-wr703n:blue:system";
-			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	reg_usb_vbus: reg_usb_vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-	};
-
-};
-
-&spi {
-	status = "okay";
-	num-cs = <1>;
-
-	flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			uboot: partition@0 {
-				reg = <0x0 0x20000>;
-				label = "u-boot";
-				read-only;
-			};
-
-			firmware: partition@20000 {
-				reg = <0x20000 0x3d0000>;
-				label = "firmware";
-			};
-
-			art: partition@3f0000 {
-				reg = <0x3f0000 0x10000>;
-				label = "art";
-				read-only;
-			};
-		};
-	};
-};
-
-&eth0 {
-	status = "okay";
-
-	mtd-mac-address = <&uboot 0x1fc00>;
-
-	gmac-config {
-		device = <&gmac>;
-
-		switch-phy-addr-swap = <0>;
-		switch-phy-swap = <0>;
-	};
-};
-
-&eth1 {
-	status = "okay";
-	compatible = "syscon", "simple-mfd";
-};
-
-&gpio {
-	status = "okay";
-};
-
-&uart {
-	status = "okay";
-};
-
-&usb {
-	dr_mode = "host";
-	vbus-supply = <&reg_usb_vbus>;
-	status = "okay";
-};
-
-&usb_phy {
-	status = "okay";
-};
-
-&wmac {
-	status = "okay";
-	mtd-cal-data = <&art 0x1000>;
-	mtd-mac-address = <&uboot 0x1fc00>;
-};