diff options
author | Lech Perczak <lech.perczak@gmail.com> | 2020-05-29 20:50:05 +0200 |
---|---|---|
committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-06-03 15:29:37 +0200 |
commit | e752fc1ff9d1d4f50a32155dd714dcde4b070bd4 (patch) | |
tree | c8b3c6f3294b007c9c1679901bfff79dc11e3642 /target/linux/ath79/base-files | |
parent | 6488d2f7cc8e895f2433d3c6b967a7048190722a (diff) | |
download | upstream-e752fc1ff9d1d4f50a32155dd714dcde4b070bd4.tar.gz upstream-e752fc1ff9d1d4f50a32155dd714dcde4b070bd4.tar.bz2 upstream-e752fc1ff9d1d4f50a32155dd714dcde4b070bd4.zip |
ath79: add support for TP-Link TL-WR802N V1 and V2
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7e513136c63108bf55b38be4d2b65aa00b0d2b26)
Diffstat (limited to 'target/linux/ath79/base-files')
-rwxr-xr-x | target/linux/ath79/base-files/etc/board.d/02_network | 2 | ||||
-rw-r--r-- | target/linux/ath79/base-files/etc/uci-defaults/04_led_migration | 6 |
2 files changed, 6 insertions, 2 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 9b9bc8a7fc..f6efc4d4d6 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -42,6 +42,8 @@ ath79_setup_interfaces() tplink,tl-wa901nd-v4|\ tplink,tl-wa901nd-v5|\ tplink,tl-wr703n|\ + tplink,tl-wr802n-v1|\ + tplink,tl-wr802n-v2|\ ubnt,bullet-m|\ ubnt,bullet-m-xw|\ ubnt,lap-120|\ diff --git a/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration index 9aa759c6a3..561aa897f4 100644 --- a/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration +++ b/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration @@ -14,14 +14,16 @@ tplink,archer-c25-v1|\ tplink,archer-c58-v1|\ tplink,archer-c59-v1|\ tplink,archer-c7-v4|\ -tplink,archer-c7-v5) +tplink,archer-c7-v5|\ +tplink,tl-wr802n-v2) migrate_leds "^$boardonly:=tp-link:" ;; tplink,archer-c7-v2|\ tplink,tl-wdr3600-v1|\ tplink,tl-wdr4300-v1|\ tplink,tl-wdr4300-v1-il|\ -tplink,tl-wdr4310-v1) +tplink,tl-wdr4310-v1|\ +tplink,tl-wr802n-v1) migrate_leds ":blue:=:green:" ;; wd,mynet-n750) |