From e752fc1ff9d1d4f50a32155dd714dcde4b070bd4 Mon Sep 17 00:00:00 2001 From: Lech Perczak Date: Fri, 29 May 2020 20:50:05 +0200 Subject: ath79: add support for TP-Link TL-WR802N V1 and V2 Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of Flash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to web interface: [V1] http://192.168.0.1 [V2] http://192.168.0.254 Default user is "admin" & password is "admin". On V2, there is no DHCP server running by default, so remember to set IP manually. - Go to "System Tools -> Firmware Upgrade" - Browse for firmware: [V1] "*.factory.bin" [V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model Web interface may complain if filename is too long. In such case, rename .bin to something shorter. - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 - Record the result of "printenv bootcmd" - Enter "erase +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm " (e.g bootm 0x9f020000) Notes: When porting from ar71xx target to ath79, I found out that on V2, reset button is on GPIO12 and active low, instead of GPIO11 and active high. By cross-flashing V1 firmware to V2, I confirmed the same is true for V1. Also according to manual of V1, this one also has green LED instead of blue - both of those issues were fixed accordingly. The MAC address assignment has been checked with OEM firmware. Installation manual based on ar71xx support by Thomas Roberts Signed-off-by: Lech Perczak [slightly adjust commit message, add MAC address comment] Signed-off-by: Adrian Schmutzler (cherry picked from commit 7e513136c63108bf55b38be4d2b65aa00b0d2b26) --- target/linux/ath79/base-files/etc/board.d/02_network | 2 ++ target/linux/ath79/base-files/etc/uci-defaults/04_led_migration | 6 ++++-- 2 files changed, 6 insertions(+), 2 deletions(-) (limited to 'target/linux/ath79/base-files') diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 9b9bc8a7fc..f6efc4d4d6 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -42,6 +42,8 @@ ath79_setup_interfaces() tplink,tl-wa901nd-v4|\ tplink,tl-wa901nd-v5|\ tplink,tl-wr703n|\ + tplink,tl-wr802n-v1|\ + tplink,tl-wr802n-v2|\ ubnt,bullet-m|\ ubnt,bullet-m-xw|\ ubnt,lap-120|\ diff --git a/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration index 9aa759c6a3..561aa897f4 100644 --- a/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration +++ b/target/linux/ath79/base-files/etc/uci-defaults/04_led_migration @@ -14,14 +14,16 @@ tplink,archer-c25-v1|\ tplink,archer-c58-v1|\ tplink,archer-c59-v1|\ tplink,archer-c7-v4|\ -tplink,archer-c7-v5) +tplink,archer-c7-v5|\ +tplink,tl-wr802n-v2) migrate_leds "^$boardonly:=tp-link:" ;; tplink,archer-c7-v2|\ tplink,tl-wdr3600-v1|\ tplink,tl-wdr4300-v1|\ tplink,tl-wdr4300-v1-il|\ -tplink,tl-wdr4310-v1) +tplink,tl-wdr4310-v1|\ +tplink,tl-wr802n-v1) migrate_leds ":blue:=:green:" ;; wd,mynet-n750) -- cgit v1.2.3