aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/etc
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2018-05-29 17:00:53 +0200
committerJohn Crispin <john@phrozen.org>2018-06-07 09:31:58 +0200
commite36f8b3f3980903d5cefc51fe274c19c7a0719f2 (patch)
tree9b3a86a9d695efc09b565dcf88f14dbe28da7253 /target/linux/ar71xx/base-files/etc
parenta84962ea35e4e97f1c4a42f2eac0242cc2cbd879 (diff)
downloadupstream-e36f8b3f3980903d5cefc51fe274c19c7a0719f2.tar.gz
upstream-e36f8b3f3980903d5cefc51fe274c19c7a0719f2.tar.bz2
upstream-e36f8b3f3980903d5cefc51fe274c19c7a0719f2.zip
ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ar71xx/base-files/etc')
-rwxr-xr-xtarget/linux/ar71xx/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ar71xx/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ar71xx/base-files/etc/diag.sh3
-rw-r--r--target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata4
4 files changed, 13 insertions, 0 deletions
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index f436854384..b53aafb0ee 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -423,6 +423,11 @@ hornet-ub-x2)
ucidef_set_led_wlan "wlan" "WLAN" "alfa:blue:wlan" "phy0tpt"
ucidef_set_led_usbdev "usb" "USB" "alfa:blue:usb" "1-1"
;;
+koala)
+ ucidef_set_led_default "power" "POWER" "$board:green:power" "1"
+ ucidef_set_led_wlan "wlan2g" "WLAN 2.4GHz" "$board:yellow:wlan2" "phy1tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN 5GHz" "$board:red:wlan58" "phy0tpt"
+ ;;
lan-turtle)
ucidef_set_led_netdev "wan" "WAN" "$board:orange:system" "eth1"
;;
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 47153d9481..5044e7f92b 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -82,6 +82,7 @@ ar71xx_setup_interfaces()
fritz300e|\
gl-usb150|\
hiveap-121|\
+ koala|\
lbe-m5|\
loco-m-xw|\
mr12|\
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 03c639a2b7..1530dded12 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -260,6 +260,9 @@ get_status_led() {
jwap230)
status_led="$board:green:led1"
;;
+ koala)
+ status_led="$board:blue:sys"
+ ;;
lan-turtle)
status_led="$board:orange:system"
;;
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index f82026c7ad..c3ae7b64ec 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -105,6 +105,10 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
+ koala)
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary art 12) +0)
+ ;;
mc-mac1200r)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)