aboutsummaryrefslogtreecommitdiffstats
path: root/package/firmware/ipq-wifi
diff options
context:
space:
mode:
authorRobert Marko <robert.marko@sartura.hr>2020-09-07 12:43:37 +0200
committerJohn Crispin <john@phrozen.org>2020-09-17 08:42:17 +0200
commit59f0a0fd839e239987ca14dcefe19717aaa71cd0 (patch)
tree681ba64eaec54f2b468e6cdf1c4142e39178ee9d /package/firmware/ipq-wifi
parent43a53891ce8f141e11960bc7b4ad369588ac341d (diff)
downloadupstream-59f0a0fd839e239987ca14dcefe19717aaa71cd0.tar.gz
upstream-59f0a0fd839e239987ca14dcefe19717aaa71cd0.tar.bz2
upstream-59f0a0fd839e239987ca14dcefe19717aaa71cd0.zip
ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Diffstat (limited to 'package/firmware/ipq-wifi')
-rw-r--r--package/firmware/ipq-wifi/Makefile2
-rw-r--r--package/firmware/ipq-wifi/board-edgecore_ecw5410.qca9984bin0 -> 24324 bytes
2 files changed, 2 insertions, 0 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 0d1a737d59..a796910186 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -31,6 +31,7 @@ ALLWIFIBOARDS:= \
buffalo_wtr-m2133hp \
cellc_rtl30vw \
dlink_dap2610 \
+ edgecore_ecw5410 \
engenius_eap2200 \
engenius_emd1 \
engenius_emr3500 \
@@ -105,6 +106,7 @@ $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
+$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
diff --git a/package/firmware/ipq-wifi/board-edgecore_ecw5410.qca9984 b/package/firmware/ipq-wifi/board-edgecore_ecw5410.qca9984
new file mode 100644
index 0000000000..2c1992001d
--- /dev/null
+++ b/package/firmware/ipq-wifi/board-edgecore_ecw5410.qca9984
Binary files differ