diff options
author | Marcel Ziswiler <marcel@ziswiler.com> | 2022-09-29 22:40:31 +0200 |
---|---|---|
committer | Hauke Mehrtens <hauke@hauke-m.de> | 2023-02-18 15:46:45 +0100 |
commit | f6d2a23cbca61611663efb531c97efeded26e0cd (patch) | |
tree | c25a04725686d756a5f9809ce8b575a944396ad0 | |
parent | 4536c76b558ca50645177a1e34bc24adda87d733 (diff) | |
download | upstream-f6d2a23cbca61611663efb531c97efeded26e0cd.tar.gz upstream-f6d2a23cbca61611663efb531c97efeded26e0cd.tar.bz2 upstream-f6d2a23cbca61611663efb531c97efeded26e0cd.zip |
mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
5 files changed, 591 insertions, 1 deletions
diff --git a/target/linux/mediatek/dts/mt7622-netgear-wax206.dts b/target/linux/mediatek/dts/mt7622-netgear-wax206.dts new file mode 100644 index 0000000000..181abb915c --- /dev/null +++ b/target/linux/mediatek/dts/mt7622-netgear-wax206.dts @@ -0,0 +1,559 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2022, Marcel Ziswiler <marcel@ziswiler.com> */ + +/dts-v1/; +#include "mt7622.dtsi" +#include "mt6380.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear WAX206"; + compatible = "netgear,wax206", "mediatek,mt7622"; + + aliases { + ethernet0 = &gmac0; + led-boot = &led_power_r; + led-failsafe = &led_power_r; + led-running = &led_power_g; + led-upgrade = &led_power_g; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512"; + }; + + cpus { + cpu@0 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; + }; + + cpu@1 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + label = "reset"; + linux,code = <KEY_RESTART>; + }; + + wps { + gpios = <&pio 102 GPIO_ACTIVE_LOW>; + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_power_r: power_red { + default-state = "on"; + gpios = <&pio 3 GPIO_ACTIVE_LOW>; + label = "power:red"; + }; + + led_power_g: power_green { + default-state = "off"; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + label = "power:green"; + }; + + inet_green { + default-state = "off"; + gpios = <&pio 20 GPIO_ACTIVE_HIGH>; + label = "inet:green"; + }; + + inet_blue { + default-state = "off"; + gpios = <&pio 17 GPIO_ACTIVE_LOW>; + label = "inet:blue"; + }; + + wifin_green { + default-state = "off"; + gpios = <&pio 85 GPIO_ACTIVE_LOW>; + label = "wifin:green"; + }; + + wifin_blue { + default-state = "off"; + gpios = <&pio 86 GPIO_ACTIVE_LOW>; + label = "wifin:blue"; + }; + + wifia_green { + default-state = "off"; + gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + label = "wifia:green"; + }; + + wifia_blue { + default-state = "off"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + label = "wifia:blue"; + }; + }; + + memory { + reg = <0 0x40000000 0 0x40000000>; + }; +}; + +&bch { + status = "okay"; +}; + +&btif { + status = "okay"; +}; + +&cir { + pinctrl-names = "default"; + pinctrl-0 = <&irrx_pins>; + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <ð_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + nvmem-cells = <&macaddr_factory_7fff4>; + nvmem-cell-names = "mac-address"; + phy-mode = "2500base-x"; + reg = <0>; + + fixed-link { + full-duplex; + pause; + speed = <2500>; + }; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7531"; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + reg = <0>; + reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + label = "lan1"; + reg = <1>; + }; + + port@2 { + label = "lan2"; + reg = <2>; + }; + + port@3 { + label = "lan3"; + reg = <3>; + }; + + port@4 { + label = "lan4"; + reg = <4>; + }; + + wan: port@5 { + label = "wan"; + nvmem-cells = <&macaddr_factory_7fffa>; + nvmem-cell-names = "mac-address"; + phy-handle = <&rtl8221b_phy>; + phy-mode = "sgmii"; + reg = <5>; + }; + + port@6 { + ethernet = <&gmac0>; + label = "cpu"; + phy-mode = "2500base-x"; + reg = <6>; + + fixed-link { + full-duplex; + pause; + speed = <2500>; + }; + }; + }; + }; + + rtl8221b_phy: ethernet-phy@7 { + compatible = "ethernet-phy-id001c.c849"; + reg = <7>; + reset-gpios = <&pio 101 GPIO_ACTIVE_LOW>; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH>; + reset-assert-us = <100000>; + reset-deassert-us = <100000>; + }; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_pins>; + status = "okay"; +}; + +&pcie1 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_pins>; + status = "okay"; +}; + +&pio { + eth_pins: eth-pins { + mux { + function = "eth"; + groups = "mdc_mdio", "rgmii_via_gmac2"; + }; + }; + + irrx_pins: irrx-pins { + mux { + function = "ir"; + groups = "ir_1_rx"; + }; + }; + + irtx_pins: irtx-pins { + mux { + function = "ir"; + groups = "ir_1_tx"; + }; + }; + + pcie0_pins: pcie0-pins { + mux { + function = "pcie"; + groups = "pcie0_pad_perst", + "pcie0_1_waken", + "pcie0_1_clkreq"; + }; + }; + + pcie1_pins: pcie1-pins { + mux { + function = "pcie"; + groups = "pcie1_pad_perst", + "pcie1_0_waken", + "pcie1_0_clkreq"; + }; + }; + + pmic_bus_pins: pmic-bus-pins { + mux { + function = "pmic"; + groups = "pmic_bus"; + }; + }; + + pwm7_pins: pwm1-2-pins { + mux { + function = "pwm"; + groups = "pwm_ch7_2"; + }; + }; + + wled_pins: wled-pins { + mux { + function = "led"; + groups = "wled"; + }; + }; + + /* Serial NAND is shared pin with SPI-NOR */ + serial_nand_pins: serial-nand-pins { + mux { + function = "flash"; + groups = "snfi"; + }; + }; + + spic0_pins: spic0-pins { + mux { + function = "spi"; + groups = "spic0_0"; + }; + }; + + spic1_pins: spic1-pins { + mux { + function = "spi"; + groups = "spic1_0"; + }; + }; + + uart0_pins: uart0-pins { + mux { + function = "uart"; + groups = "uart0_0_tx_rx"; + }; + }; + + uart2_pins: uart2-pins { + mux { + function = "uart"; + groups = "uart2_1_tx_rx"; + }; + }; + + watchdog_pins: watchdog-pins { + mux { + function = "watchdog"; + groups = "watchdog"; + }; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm7_pins>; + status = "okay"; +}; + +&pwrap { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_bus_pins>; + status = "okay"; +}; + +&rtc { + status = "disabled"; +}; + +&sata { + status = "disabled"; +}; + +&sata_phy { + status = "disabled"; +}; + +&slot0 { + wmac1: mt7915@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&snfi { + pinctrl-names = "default"; + pinctrl-0 = <&serial_nand_pins>; + status = "okay"; + + snand: flash@0 { + compatible = "spi-nand"; + mediatek,bmt-table-size = <0x1000>; + mediatek,bmt-v2; + nand-ecc-engine = <&snfi>; + reg = <0>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Preloader"; + reg = <0x00000 0x0080000>; + read-only; + }; + + partition@80000 { + label = "ATF"; + reg = <0x80000 0x0040000>; + read-only; + }; + + partition@c0000 { + label = "Bootloader"; + reg = <0xc0000 0x0080000>; + read-only; + }; + + partition@140000 { + label = "Config"; + reg = <0x140000 0x0080000>; + }; + + factory: partition@1c0000 { + compatible = "nvmem-cells"; + label = "Factory"; + reg = <0x1c0000 0x0100000>; + #address-cells = <1>; + #size-cells = <1>; + read-only; + + macaddr_factory_7fff4: macaddr@7fff4 { + reg = <0x7fff4 0x6>; + }; + + macaddr_factory_7fffa: macaddr@7fffa { + reg = <0x7fffa 0x6>; + }; + }; + + partition@2c0000 { + label = "firmware"; + reg = <0x2c0000 0x2600000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x600000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x600000 0x2000000>; + }; + }; + + partition@28c0000 { + label = "firmware_backup"; + reg = <0x28c0000 0x2600000>; + read-only; + }; + + partition@4ec0000 { + label = "CFG"; + reg = <0x4ec0000 0x800000>; + read-only; + }; + + partition@56c0000 { + label = "RAE"; + reg = <0x56c0000 0x400000>; + read-only; + }; + + partition@5ac0000 { + label = "POT"; + reg = <0x5ac0000 0x100000>; + read-only; + }; + + partition@5bc0000 { + label = "Language"; + reg = <0x5bc0000 0x400000>; + read-only; + }; + + partition@5fc0000 { + label = "Traffic"; + reg = <0x5fc0000 0x200000>; + read-only; + }; + + partition@61c0000 { + label = "Cert"; + reg = <0x61c0000 0x100000>; + read-only; + }; + + partition@62c0000 { + label = "NTGRcryptK"; + reg = <0x62c0000 0x100000>; + read-only; + }; + + partition@63c0000 { + label = "NTGRcryptD"; + reg = <0x63c0000 0x500000>; + read-only; + }; + + partition@68c0000 { + label = "LOG"; + reg = <0x68c0000 0x100000>; + read-only; + }; + + partition@69c0000 { + label = "User_data"; + reg = <0x69c0000 0x640000>; + read-only; + }; + + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spic0_pins>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spic1_pins>; + status = "okay"; +}; + +&ssusb { + status = "disabled"; +}; + +&u3phy { + status = "disabled"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&watchdog { + pinctrl-names = "default"; + pinctrl-0 = <&watchdog_pins>; + status = "okay"; +}; + +&wmac { + mediatek,mtd-eeprom = <&factory 0x0000>; + status = "okay"; +}; + +&wmac1 { + mediatek,mtd-eeprom = <&factory 0x05000>; +}; diff --git a/target/linux/mediatek/image/mt7622.mk b/target/linux/mediatek/image/mt7622.mk index 097ddd6bfd..ee71cf8764 100644 --- a/target/linux/mediatek/image/mt7622.mk +++ b/target/linux/mediatek/image/mt7622.mk @@ -228,6 +228,33 @@ define Device/mediatek_mt7622-rfb1-ubi endef TARGET_DEVICES += mediatek_mt7622-rfb1-ubi +define Device/netgear_wax206 + $(Device/dsa-migration) + DEVICE_VENDOR := NETGEAR + DEVICE_MODEL := WAX206 + DEVICE_DTS := mt7622-netgear-wax206 + DEVICE_DTS_DIR := ../dts + NETGEAR_ENC_MODEL := WAX206 + NETGEAR_ENC_REGION := US + DEVICE_PACKAGES := kmod-mt7915-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 6144k + IMAGE_SIZE := 32768k + KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \ + append-squashfs4-fakeroot +# recovery can also be used with stock firmware web-ui, hence the padding... + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 128k + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + IMAGES += factory.img + IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \ + append-ubi | check-size | netgear-encrypted-factory + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += netgear_wax206 + define Device/ruijie_rg-ew3200gx-pro DEVICE_VENDOR := Ruijie DEVICE_MODEL := RG-EW3200GX PRO diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds b/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds index 5c32918d35..7cb54186fd 100644 --- a/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds @@ -7,7 +7,8 @@ board_config_update case $board in linksys,e8450|\ -linksys,e8450-ubi) +linksys,e8450-ubi|\ +netgear,wax206) ucidef_set_led_netdev "wan" "WAN" "inet:blue" "wan" ;; xiaomi,redmi-router-ax6s) diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network index 5312bf5c56..38db921f5c 100644 --- a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network @@ -14,6 +14,7 @@ mediatek_setup_interfaces() linksys,e8450-ubi|\ mediatek,mt7622-rfb1|\ mediatek,mt7622-rfb1-ubi|\ + netgear,wax206|\ reyee,ax3200-e5|\ ruijie,rg-ew3200gx-pro) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan diff --git a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh index e3c66a3b01..b37b7b1c6e 100755 --- a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh @@ -35,6 +35,7 @@ platform_do_upgrade() { ;; elecom,wrc-x3200gst3|\ mediatek,mt7622-rfb1-ubi|\ + netgear,wax206|\ totolink,a8000ru|\ xiaomi,redmi-router-ax6s) nand_do_upgrade "$1" @@ -71,6 +72,7 @@ platform_check_image() { ;; elecom,wrc-x3200gst3|\ mediatek,mt7622-rfb1-ubi|\ + netgear,wax206|\ totolink,a8000ru|\ xiaomi,redmi-router-ax6s) nand_do_platform_check "$board" "$1" |