aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorINAGAKI Hiroshi <musashino.open@gmail.com>2018-11-30 19:04:23 +0900
committerMathias Kresin <dev@kresin.me>2018-12-06 20:26:57 +0100
commit3358cae5238d66c73b0328b007a1cbb073bc8275 (patch)
tree65011b51cf01491bfed2d6f61c5187eafa22bb23
parent9dd7147f6bce44a49fef594f55b120253baf5556 (diff)
downloadupstream-3358cae5238d66c73b0328b007a1cbb073bc8275.tar.gz
upstream-3358cae5238d66c73b0328b007a1cbb073bc8275.tar.bz2
upstream-3358cae5238d66c73b0328b007a1cbb073bc8275.zip
ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom3
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac6
-rw-r--r--target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts222
-rw-r--r--target/linux/ath79/image/generic.mk12
5 files changed, 245 insertions, 2 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 266a18791a..fa7a618909 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -82,6 +82,7 @@ ath79_setup_interfaces()
iodata,etg3-r|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2|\
+ iodata,wn-ag300dgr|\
pcs,cr5000)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
@@ -223,7 +224,8 @@ ath79_setup_macs()
wan_mac=$(macaddr_add "$lan_mac" -1)
;;
iodata,wn-ac1167dgr|\
- iodata,wn-ac1600dgr2)
+ iodata,wn-ac1600dgr2|\
+ iodata,wn-ag300dgr)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index c5cbac7514..e4d4a597a9 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -101,7 +101,8 @@ case "$FIRMWARE" in
ath9k_eeprom_extract_reverse "urlader" 5441 1088
;;
iodata,wn-ac1167dgr|\
- iodata,wn-ac1600dgr2)
+ iodata,wn-ac1600dgr2|\
+ iodata,wn-ag300dgr)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
index fe5aa64a19..bb55b1c11c 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
+++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
@@ -13,6 +13,12 @@ PHYNBR=${DEVPATH##*/phy}
board=$(board_name)
case "$board" in
+ iodata,wn-ag300dgr)
+ # There is no eeprom data for 5 GHz wlan in "art" partition
+ # which would allow to patch the macaddress
+ [ "$PHYNBR" -eq 1 ] && \
+ echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress
+ ;;
phicomm,k2t)
# The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address
[ "$PHYNBR" -eq 1 ] && \
diff --git a/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts b/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts
new file mode 100644
index 0000000000..b222b10a5a
--- /dev/null
+++ b/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ compatible = "iodata,wn-ag300dgr", "qca,ar9344";
+ model = "I-O DATA WN-AG300DGR";
+
+ aliases {
+ led-boot = &router;
+ led-failsafe = &router;
+ led-running = &router;
+ led-upgrade = &router;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ router: router {
+ label = "wn-ag300dgr:green:router";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ children {
+ label = "wn-ag300dgr:green:children";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ eco {
+ label = "wn-ag300dgr:green:eco";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ notification {
+ label = "wn-ag300dgr:amber:notification";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ wlan2g {
+ label = "wn-ag300dgr:green:wlan2g";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "wn-ag300dgr:green:wlan5g";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ eco {
+ label = "eco";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ debounce-interval = <60>;
+ };
+
+ router {
+ label = "router";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ debounce-interval = <60>;
+ };
+
+ auto {
+ label = "auto";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ children {
+ label = "children";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&ref {
+ clock-frequency = <25000000>;
+};
+
+&spi {
+ num-cs = <1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x030000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x030000 0x010000>;
+ read-only;
+ };
+
+ partition@40000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x040000 0xf10000>;
+ };
+
+ partition@f50000 {
+ label = "manufacture";
+ reg = <0xf50000 0x40000>;
+ read-only;
+ };
+
+ partition@f90000 {
+ label = "backup";
+ reg = <0xf90000 0x10000>;
+ read-only;
+ };
+
+ partition@fa0000 {
+ label = "storage";
+ reg = <0xfa0000 0x50000>;
+ read-only;
+ };
+
+ partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ phy-mode = "rgmii";
+
+ qca,ar8327-initvals = <
+ 0x04 0x07a00000 /* PORT0 PAD MODE CTRL */
+ 0x7c 0x000000fe /* PORT0_STATUS */
+ >;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ pll-data = <0x06000000 0x00000101 0x00001616>;
+
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-gmac0 = <1>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+ qca,no-eeprom;
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 74d185ea63..df91c91826 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -222,6 +222,18 @@ define Device/iodata_wn-ac1600dgr2
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
+define Device/iodata_wn-ag300dgr
+ ATH_SOC := ar1022
+ DEVICE_TITLE := I-O DATA WN-AG300DGR
+ IMAGE_SIZE := 15424k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
+ senao-header -r 0x30a -p 0x47 -t 2
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2
+endef
+TARGET_DEVICES += iodata_wn-ag300dgr
+
define Device/ocedo_koala
ATH_SOC := qca9558
DEVICE_TITLE := OCEDO Koala