aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/patches-4.4/0074-mtd-mediatek-device-tree-docs-for-MTK-Smart-Device-G.patch
blob: 27572c1e1913e02af0344bcae45730e20eaccda3 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
From 5e1c00983efeca4522ac2e8574e3e3997d26a203 Mon Sep 17 00:00:00 2001
From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Date: Fri, 29 Apr 2016 12:17:21 -0400
Subject: [PATCH 074/102] mtd: mediatek: device tree docs for MTK Smart Device
 Gen1 NAND

This patch adds documentation support for Smart Device Gen1 type of
NAND controllers.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 Documentation/devicetree/bindings/mtd/mtk-nand.txt |  161 ++++++++++++++++++++
 1 file changed, 161 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
new file mode 100644
index 0000000..175767d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
@@ -0,0 +1,161 @@
+MTK SoCs NAND FLASH controller (NFC) DT binding
+
+This file documents the device tree bindings for MTK SoCs NAND controllers.
+The functional split of the controller requires two drivers to operate:
+the nand controller interface driver and the ECC engine driver.
+
+The hardware description for both devices must be captured as device
+tree nodes.
+
+1) NFC NAND Controller Interface (NFI):
+=======================================
+
+The first part of NFC is NAND Controller Interface (NFI) HW.
+Required NFI properties:
+- compatible:			Should be "mediatek,mtxxxx-nfc".
+- reg:				Base physical address and size of NFI.
+- interrupts:			Interrupts of NFI.
+- clocks:			NFI required clocks.
+- clock-names:			NFI clocks internal name.
+- status:			Disabled default. Then set "okay" by platform.
+- ecc-engine:			Required ECC Engine node.
+- #address-cells:		NAND chip index, should be 1.
+- #size-cells:			Should be 0.
+
+Example:
+
+	nandc: nfi@1100d000 {
+		compatible = "mediatek,mt2701-nfc";
+		reg = <0 0x1100d000 0 0x1000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI>,
+			 <&pericfg CLK_PERI_NFI_PAD>;
+		clock-names = "nfi_clk", "pad_clk";
+		status = "disabled";
+		ecc-engine = <&bch>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+        };
+
+Platform related properties, should be set in {platform_name}.dts:
+- children nodes:	NAND chips.
+
+Children nodes properties:
+- reg:			Chip Select Signal, default 0.
+			Set as reg = <0>, <1> when need 2 CS.
+Optional:
+- nand-on-flash-bbt:	Store BBT on NAND Flash.
+- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
+- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
+			The controller only supports 512 and 1024.
+			For large page NANDs ther recommended value is 1024.
+- nand-ecc-strength:	Number of bits to correct per ECC step.
+			The valid values that the controller supports are: 4, 6,
+			8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44,
+			48, 52, 56, 60.
+			The strength should be calculated as follows:
+			E = (S - F) * 8 / 14
+			S = O / (P / Q)
+				E :nand-ecc-strength;
+				S :spare size per sector;
+				F : FDM size, should be in the range [1,8].
+				    It is used to store free oob data.
+				O : oob size;
+				P : page size;
+				Q :nand-ecc-step-size
+			If the result does not match any one of the listed
+			choices above, please select the smaller valid value from
+			the list.
+			(otherwise the driver will do the clamping at runtime).
+- vmch-supply:		NAND power supply.
+- pinctrl-names:	Default NAND pin GPIO setting name.
+- pinctrl-0:		GPIO setting node.
+
+Example:
+	&pio {
+		nand_pins_default: nanddefault {
+			pins_dat {
+				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
+					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
+					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
+					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
+					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
+					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
+					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
+					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
+					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
+				input-enable;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up;
+			};
+
+			pins_we {
+				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+			};
+
+			pins_ale {
+				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+			};
+		};
+	};
+
+	&nandc {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&nand_pins_default>;
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <24>;
+			nand-ecc-step-size = <1024>;
+		};
+	};
+
+NAND chip optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			preloader@0 {
+				label = "pl";
+				read-only;
+				reg = <0x00000000 0x00400000>;
+			};
+			android@0x00400000 {
+				label = "android";
+				reg = <0x00400000 0x12c00000>;
+			};
+		};
+	};
+
+2) ECC Engine:
+==============
+
+Required BCH properties:
+- compatible:	Should be "mediatek,mtxxxx-ecc".
+- reg:		Base physical address and size of ECC.
+- interrupts:	Interrupts of ECC.
+- clocks:	ECC required clocks.
+- clock-names:	ECC clocks internal name.
+- status:	Disabled default. Then set "okay" by platform.
+
+Example:
+
+	bch: ecc@1100e000 {
+		compatible = "mediatek,mt2701-ecc";
+		reg = <0 0x1100e000 0 0x1000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI_ECC>;
+		clock-names = "nfiecc_clk";
+		status = "disabled";
+	};
-- 
1.7.10.4