aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch')
-rw-r--r--target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch123
1 files changed, 123 insertions, 0 deletions
diff --git a/target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch
new file mode 100644
index 0000000000..783770e548
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.14/511-board_V2500V.patch
@@ -0,0 +1,123 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -927,6 +927,65 @@ static struct board_info __initdata boar
+ },
+ },
+ };
++
++static struct board_info __initdata board_V2500V_BB = {
++ .name = "V2500V_BB",
++ .expected_cpu_id = 0x6348,
++
++ .has_uart0 = 1,
++ .has_enet0 = 1,
++ .has_enet1 = 1,
++ .has_pci = 1,
++
++ .enet0 = {
++ .has_phy = 1,
++ .use_internal_phy = 1,
++ },
++ .enet1 = {
++ .has_phy = 1,
++ .phy_id = 0,
++ .force_speed_100 = 1,
++ .force_duplex_full = 1,
++ },
++
++ .leds = {
++ {
++ .name = "V2500V_BB:green:power",
++ .gpio = 0,
++ .active_low = 1,
++ .default_trigger = "default-on",
++ },
++ {
++ .name = "V2500V_BB:red:power",
++ .gpio = 1,
++ .active_low = 1,
++ },
++ {
++ .name = "V2500V_BB:green:adsl",
++ .gpio = 2,
++ .active_low = 1,
++ },
++ { .name = "V2500V_BB:green:ppp",
++ .gpio = 3,
++ .active_low = 1,
++ },
++ {
++ .name = "V2500V_BB:green:wireless",
++ .gpio = 6,
++ .active_low = 1,
++ },
++ },
++ .buttons = {
++ {
++ .desc = "reset",
++ .gpio = 31,
++ .active_low = 1,
++ .type = EV_KEY,
++ .code = KEY_RESTART,
++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++ },
++ },
++};
+ #endif
+
+ /*
+@@ -2001,6 +2060,7 @@ static const struct board_info __initcon
+ &board_96348_D4PW,
+ &board_spw500v,
+ &board_96348sv,
++ &board_V2500V_BB,
+ #endif
+
+ #ifdef CONFIG_BCM63XX_CPU_6358
+@@ -2122,6 +2182,22 @@ void __init board_prom_init(void)
+ val &= MPI_CSBASE_BASE_MASK;
+ }
+ boot_addr = (u8 *)KSEG1ADDR(val);
++ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
++
++ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
++ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
++ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
++ /* Do an early check of CFE and then select bank 0 */
++
++ if (boot_addr == (u8 *)0xbf800000) {
++ u8 *tmp_boot_addr = (u8*)0xbfc00000;
++
++ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
++ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
++ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
++ boot_addr = tmp_boot_addr;
++ }
++ }
+
+ /* dump cfe version */
+ cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -19,6 +19,7 @@
+ #include <linux/spi/spi.h>
+ #include <linux/spi/flash.h>
+
++#include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_hsspi.h>
+@@ -207,6 +208,13 @@ int __init bcm63xx_flash_register(int nu
+ val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+ val &= MPI_CSBASE_BASE_MASK;
+
++ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
++ /* Loading from CFE always uses Bank 0 */
++ if (!strcmp(board_get_name(), "V2500V_BB")) {
++ pr_info("V2500V: Start in Bank 0\n");
++ val = val + 0x400000; // Select Bank 0 start address
++ }
++
+ mtd_resources[0].start = val;
+ mtd_resources[0].end = 0x1FFFFFFF;
+