diff options
Diffstat (limited to 'include/linux/regulator/consumer.h')
| -rw-r--r-- | include/linux/regulator/consumer.h | 303 |
1 files changed, 303 insertions, 0 deletions
diff --git a/include/linux/regulator/consumer.h b/include/linux/regulator/consumer.h new file mode 100644 index 00000000..9e87c1cb --- /dev/null +++ b/include/linux/regulator/consumer.h @@ -0,0 +1,303 @@ +/* + * consumer.h -- SoC Regulator consumer support. + * + * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. + * + * Author: Liam Girdwood <lrg@slimlogic.co.uk> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Regulator Consumer Interface. + * + * A Power Management Regulator framework for SoC based devices. + * Features:- + * o Voltage and current level control. + * o Operating mode control. + * o Regulator status. + * o sysfs entries for showing client devices and status + * + * EXPERIMENTAL FEATURES: + * Dynamic Regulator operating Mode Switching (DRMS) - allows regulators + * to use most efficient operating mode depending upon voltage and load and + * is transparent to client drivers. + * + * e.g. Devices x,y,z share regulator r. Device x and y draw 20mA each during + * IO and 1mA at idle. Device z draws 100mA when under load and 5mA when + * idling. Regulator r has > 90% efficiency in NORMAL mode at loads > 100mA + * but this drops rapidly to 60% when below 100mA. Regulator r has > 90% + * efficiency in IDLE mode at loads < 10mA. Thus regulator r will operate + * in normal mode for loads > 10mA and in IDLE mode for load <= 10mA. + * + */ + +#ifndef __LINUX_REGULATOR_CONSUMER_H_ +#define __LINUX_REGULATOR_CONSUMER_H_ + +#include <linux/device.h> + +/* + * Regulator operating modes. + * + * Regulators can run in a variety of different operating modes depending on + * output load. This allows further system power savings by selecting the + * best (and most efficient) regulator mode for a desired load. + * + * Most drivers will only care about NORMAL. The modes below are generic and + * will probably not match the naming convention of your regulator data sheet + * but should match the use cases in the datasheet. + * + * In order of power efficiency (least efficient at top). + * + * Mode Description + * FAST Regulator can handle fast changes in it's load. + * e.g. useful in CPU voltage & frequency scaling where + * load can quickly increase with CPU frequency increases. + * + * NORMAL Normal regulator power supply mode. Most drivers will + * use this mode. + * + * IDLE Regulator runs in a more efficient mode for light + * loads. Can be used for devices that have a low power + * requirement during periods of inactivity. This mode + * may be more noisy than NORMAL and may not be able + * to handle fast load switching. + * + * STANDBY Regulator runs in the most efficient mode for very + * light loads. Can be used by devices when they are + * in a sleep/standby state. This mode is likely to be + * the most noisy and may not be able to handle fast load + * switching. + * + * NOTE: Most regulators will only support a subset of these modes. Some + * will only just support NORMAL. + * + * These modes can be OR'ed together to make up a mask of valid register modes. + */ + +#define REGULATOR_MODE_FAST 0x1 +#define REGULATOR_MODE_NORMAL 0x2 +#define REGULATOR_MODE_IDLE 0x4 +#define REGULATOR_MODE_STANDBY 0x8 + +/* + * Regulator notifier events. + * + * UNDER_VOLTAGE Regulator output is under voltage. + * OVER_CURRENT Regulator output current is too high. + * REGULATION_OUT Regulator output is out of regulation. + * FAIL Regulator output has failed. + * OVER_TEMP Regulator over temp. + * FORCE_DISABLE Regulator forcibly shut down by software. + * VOLTAGE_CHANGE Regulator voltage changed. + * DISABLE Regulator was disabled. + * + * NOTE: These events can be OR'ed together when passed into handler. + */ + +#define REGULATOR_EVENT_UNDER_VOLTAGE 0x01 +#define REGULATOR_EVENT_OVER_CURRENT 0x02 +#define REGULATOR_EVENT_REGULATION_OUT 0x04 +#define REGULATOR_EVENT_FAIL 0x08 +#define REGULATOR_EVENT_OVER_TEMP 0x10 +#define REGULATOR_EVENT_FORCE_DISABLE 0x20 +#define REGULATOR_EVENT_VOLTAGE_CHANGE 0x40 +#define REGULATOR_EVENT_DISABLE 0x80 + +struct regulator; + +/** + * struct regulator_bulk_data - Data used for bulk regulator operations. + * + * @supply: The name of the supply. Initialised by the user before + * using the bulk regulator APIs. + * @consumer: The regulator consumer for the supply. This will be managed + * by the bulk API. + * + * The regulator APIs provide a series of regulator_bulk_() API calls as + * a convenience to consumers which require multiple supplies. This + * structure is used to manage data for these calls. + */ +struct regulator_bulk_data { + const char *supply; + struct regulator *consumer; +}; + +#if defined(CONFIG_REGULATOR) + +/* regulator get and put */ +struct regulator *__must_check regulator_get(struct device *dev, + const char *id); +struct regulator *__must_check regulator_get_exclusive(struct device *dev, + const char *id); +void regulator_put(struct regulator *regulator); + +/* regulator output control and status */ +int regulator_enable(struct regulator *regulator); +int regulator_disable(struct regulator *regulator); +int regulator_force_disable(struct regulator *regulator); +int regulator_is_enabled(struct regulator *regulator); + +int regulator_bulk_get(struct device *dev, int num_consumers, + struct regulator_bulk_data *consumers); +int regulator_bulk_enable(int num_consumers, + struct regulator_bulk_data *consumers); +int regulator_bulk_disable(int num_consumers, + struct regulator_bulk_data *consumers); +void regulator_bulk_free(int num_consumers, + struct regulator_bulk_data *consumers); + +int regulator_count_voltages(struct regulator *regulator); +int regulator_list_voltage(struct regulator *regulator, unsigned selector); +int regulator_is_supported_voltage(struct regulator *regulator, + int min_uV, int max_uV); +int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV); +int regulator_set_voltage_time(struct regulator *regulator, + int old_uV, int new_uV); +int regulator_get_voltage(struct regulator *regulator); +int regulator_sync_voltage(struct regulator *regulator); +int regulator_set_current_limit(struct regulator *regulator, + int min_uA, int max_uA); +int regulator_get_current_limit(struct regulator *regulator); + +int regulator_set_mode(struct regulator *regulator, unsigned int mode); +unsigned int regulator_get_mode(struct regulator *regulator); +int regulator_set_optimum_mode(struct regulator *regulator, int load_uA); + +/* regulator notifier block */ +int regulator_register_notifier(struct regulator *regulator, + struct notifier_block *nb); +int regulator_unregister_notifier(struct regulator *regulator, + struct notifier_block *nb); + +/* driver data - core doesn't touch */ +void *regulator_get_drvdata(struct regulator *regulator); +void regulator_set_drvdata(struct regulator *regulator, void *data); + +#else + +/* + * Make sure client drivers will still build on systems with no software + * controllable voltage or current regulators. + */ +static inline struct regulator *__must_check regulator_get(struct device *dev, + const char *id) +{ + /* Nothing except the stubbed out regulator API should be + * looking at the value except to check if it is an error + * value. Drivers are free to handle NULL specifically by + * skipping all regulator API calls, but they don't have to. + * Drivers which don't, should make sure they properly handle + * corner cases of the API, such as regulator_get_voltage() + * returning 0. + */ + return NULL; +} +static inline void regulator_put(struct regulator *regulator) +{ +} + +static inline int regulator_enable(struct regulator *regulator) +{ + return 0; +} + +static inline int regulator_disable(struct regulator *regulator) +{ + return 0; +} + +static inline int regulator_is_enabled(struct regulator *regulator) +{ + return 1; +} + +static inline int regulator_bulk_get(struct device *dev, + int num_consumers, + struct regulator_bulk_data *consumers) +{ + return 0; +} + +static inline int regulator_bulk_enable(int num_consumers, + struct regulator_bulk_data *consumers) +{ + return 0; +} + +static inline int regulator_bulk_disable(int num_consumers, + struct regulator_bulk_data *consumers) +{ + return 0; +} + +static inline void regulator_bulk_free(int num_consumers, + struct regulator_bulk_data *consumers) +{ +} + +static inline int regulator_set_voltage(struct regulator *regulator, + int min_uV, int max_uV) +{ + return 0; +} + +static inline int regulator_get_voltage(struct regulator *regulator) +{ + return 0; +} + +static inline int regulator_set_current_limit(struct regulator *regulator, + int min_uA, int max_uA) +{ + return 0; +} + +static inline int regulator_get_current_limit(struct regulator *regulator) +{ + return 0; +} + +static inline int regulator_set_mode(struct regulator *regulator, + unsigned int mode) +{ + return 0; +} + +static inline unsigned int regulator_get_mode(struct regulator *regulator) +{ + return REGULATOR_MODE_NORMAL; +} + +static inline int regulator_set_optimum_mode(struct regulator *regulator, + int load_uA) +{ + return REGULATOR_MODE_NORMAL; +} + +static inline int regulator_register_notifier(struct regulator *regulator, + struct notifier_block *nb) +{ + return 0; +} + +static inline int regulator_unregister_notifier(struct regulator *regulator, + struct notifier_block *nb) +{ + return 0; +} + +static inline void *regulator_get_drvdata(struct regulator *regulator) +{ + return NULL; +} + +static inline void regulator_set_drvdata(struct regulator *regulator, + void *data) +{ +} + +#endif + +#endif |