diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
4 files changed, 126 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt new file mode 100644 index 00000000..777abd73 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -0,0 +1,53 @@ +* SPI (Serial Peripheral Interface) + +Required properties: +- cell-index : QE SPI subblock index. + 0: QE subblock SPI1 + 1: QE subblock SPI2 +- compatible : should be "fsl,spi". +- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + +Example: + spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> + }; + + +* eSPI (Enhanced Serial Peripheral Interface) + +Required properties: +- compatible : should be "fsl,mpc8536-espi". +- reg : Offset and length of the register set for the device. +- interrupts : should contain eSPI interrupt, the device has one interrupt. +- fsl,espi-num-chipselects : the number of the chipselect signals. + +Example: + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2>; + interrupt-parent = <&mpic>; + fsl,espi-num-chipselects = <4>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt new file mode 100644 index 00000000..e782add2 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -0,0 +1,57 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi_altera.txt b/Documentation/devicetree/bindings/spi/spi_altera.txt new file mode 100644 index 00000000..dda37594 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_altera.txt @@ -0,0 +1,4 @@ +Altera SPI + +Required properties: +- compatible : should be "ALTR,spi-1.0". diff --git a/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt new file mode 100644 index 00000000..d95c0b36 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt @@ -0,0 +1,12 @@ +OpenCores tiny SPI + +Required properties: +- compatible : should be "opencores,tiny-spi-rtlsvn2". +- gpios : should specify GPIOs used for chipselect. +Optional properties: +- clock-frequency : input clock frequency to the core. +- baud-width: width, in bits, of the programmable divider used to scale + the input clock to SCLK. + +The clock-frequency and baud-width properties are needed only if the divider +is programmable. They are not needed if the divider is fixed. |