diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 4383 |
1 files changed, 4383 insertions, 0 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h new file mode 100644 index 0000000..e96b92f --- /dev/null +++ b/include/net/mac80211.h @@ -0,0 +1,4383 @@ +/* + * mac80211 <-> driver interface + * + * Copyright 2002-2005, Devicescape Software, Inc. + * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz> + * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef MAC80211_H +#define MAC80211_H + +#include <linux/bug.h> +#include <linux/kernel.h> +#include <linux/if_ether.h> +#include <linux/skbuff.h> +#include <linux/ieee80211.h> +#include <net/cfg80211.h> +#include <asm/unaligned.h> + +/** + * DOC: Introduction + * + * mac80211 is the Linux stack for 802.11 hardware that implements + * only partial functionality in hard- or firmware. This document + * defines the interface between mac80211 and low-level hardware + * drivers. + */ + +/** + * DOC: Calling mac80211 from interrupts + * + * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be + * called in hardware interrupt context. The low-level driver must not call any + * other functions in hardware interrupt context. If there is a need for such + * call, the low-level driver should first ACK the interrupt and perform the + * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even + * tasklet function. + * + * NOTE: If the driver opts to use the _irqsafe() functions, it may not also + * use the non-IRQ-safe functions! + */ + +/** + * DOC: Warning + * + * If you're reading this document and not the header file itself, it will + * be incomplete because not all documentation has been converted yet. + */ + +/** + * DOC: Frame format + * + * As a general rule, when frames are passed between mac80211 and the driver, + * they start with the IEEE 802.11 header and include the same octets that are + * sent over the air except for the FCS which should be calculated by the + * hardware. + * + * There are, however, various exceptions to this rule for advanced features: + * + * The first exception is for hardware encryption and decryption offload + * where the IV/ICV may or may not be generated in hardware. + * + * Secondly, when the hardware handles fragmentation, the frame handed to + * the driver from mac80211 is the MSDU, not the MPDU. + * + * Finally, for received frames, the driver is able to indicate that it has + * filled a radiotap header and put that in front of the frame; if it does + * not do so then mac80211 may add this under certain circumstances. + */ + +/** + * DOC: mac80211 workqueue + * + * mac80211 provides its own workqueue for drivers and internal mac80211 use. + * The workqueue is a single threaded workqueue and can only be accessed by + * helpers for sanity checking. Drivers must ensure all work added onto the + * mac80211 workqueue should be cancelled on the driver stop() callback. + * + * mac80211 will flushed the workqueue upon interface removal and during + * suspend. + * + * All work performed on the mac80211 workqueue must not acquire the RTNL lock. + * + */ + +struct device; + +/** + * enum ieee80211_max_queues - maximum number of queues + * + * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues. + * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set + */ +enum ieee80211_max_queues { + IEEE80211_MAX_QUEUES = 16, + IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1, +}; + +#define IEEE80211_INVAL_HW_QUEUE 0xff + +/** + * enum ieee80211_ac_numbers - AC numbers as used in mac80211 + * @IEEE80211_AC_VO: voice + * @IEEE80211_AC_VI: video + * @IEEE80211_AC_BE: best effort + * @IEEE80211_AC_BK: background + */ +enum ieee80211_ac_numbers { + IEEE80211_AC_VO = 0, + IEEE80211_AC_VI = 1, + IEEE80211_AC_BE = 2, + IEEE80211_AC_BK = 3, +}; +#define IEEE80211_NUM_ACS 4 + +/** + * struct ieee80211_tx_queue_params - transmit queue configuration + * + * The information provided in this structure is required for QoS + * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29. + * + * @aifs: arbitration interframe space [0..255] + * @cw_min: minimum contention window [a value of the form + * 2^n-1 in the range 1..32767] + * @cw_max: maximum contention window [like @cw_min] + * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled + * @acm: is mandatory admission control required for the access category + * @uapsd: is U-APSD mode enabled for the queue + */ +struct ieee80211_tx_queue_params { + u16 txop; + u16 cw_min; + u16 cw_max; + u8 aifs; + bool acm; + bool uapsd; +}; + +struct ieee80211_low_level_stats { + unsigned int dot11ACKFailureCount; + unsigned int dot11RTSFailureCount; + unsigned int dot11FCSErrorCount; + unsigned int dot11RTSSuccessCount; +}; + +/** + * enum ieee80211_chanctx_change - change flag for channel context + * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed + * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed + * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed + */ +enum ieee80211_chanctx_change { + IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), + IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), + IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), +}; + +/** + * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to + * + * This is the driver-visible part. The ieee80211_chanctx + * that contains it is visible in mac80211 only. + * + * @def: the channel definition + * @rx_chains_static: The number of RX chains that must always be + * active on the channel to receive MIMO transmissions + * @rx_chains_dynamic: The number of RX chains that must be enabled + * after RTS/CTS handshake to receive SMPS MIMO transmissions; + * this will always be >= @rx_chains_static. + * @radar_enabled: whether radar detection is enabled on this channel. + * @drv_priv: data area for driver use, will always be aligned to + * sizeof(void *), size is determined in hw information. + */ +struct ieee80211_chanctx_conf { + struct cfg80211_chan_def def; + + u8 rx_chains_static, rx_chains_dynamic; + + bool radar_enabled; + + u8 drv_priv[0] __aligned(sizeof(void *)); +}; + +/** + * enum ieee80211_bss_change - BSS change notification flags + * + * These flags are used with the bss_info_changed() callback + * to indicate which BSS parameter changed. + * + * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated), + * also implies a change in the AID. + * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed + * @BSS_CHANGED_ERP_PREAMBLE: preamble changed + * @BSS_CHANGED_ERP_SLOT: slot timing changed + * @BSS_CHANGED_HT: 802.11n parameters changed + * @BSS_CHANGED_BASIC_RATES: Basic rateset changed + * @BSS_CHANGED_BEACON_INT: Beacon interval changed + * @BSS_CHANGED_BSSID: BSSID changed, for whatever + * reason (IBSS and managed mode) + * @BSS_CHANGED_BEACON: Beacon data changed, retrieve + * new beacon (beaconing modes) + * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be + * enabled/disabled (beaconing modes) + * @BSS_CHANGED_CQM: Connection quality monitor config changed + * @BSS_CHANGED_IBSS: IBSS join status changed + * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed. + * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note + * that it is only ever disabled for station mode. + * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. + * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode) + * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode) + * @BSS_CHANGED_PS: PS changed for this BSS (STA mode) + * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface + * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS) + * changed (currently only in P2P client mode, GO mode will be later) + * @BSS_CHANGED_DTIM_PERIOD: the DTIM period value was changed (set when + * it becomes valid, managed mode only) + * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, + * note that this is only called when it changes after the channel + * context had been assigned. + */ +enum ieee80211_bss_change { + BSS_CHANGED_ASSOC = 1<<0, + BSS_CHANGED_ERP_CTS_PROT = 1<<1, + BSS_CHANGED_ERP_PREAMBLE = 1<<2, + BSS_CHANGED_ERP_SLOT = 1<<3, + BSS_CHANGED_HT = 1<<4, + BSS_CHANGED_BASIC_RATES = 1<<5, + BSS_CHANGED_BEACON_INT = 1<<6, + BSS_CHANGED_BSSID = 1<<7, + BSS_CHANGED_BEACON = 1<<8, + BSS_CHANGED_BEACON_ENABLED = 1<<9, + BSS_CHANGED_CQM = 1<<10, + BSS_CHANGED_IBSS = 1<<11, + BSS_CHANGED_ARP_FILTER = 1<<12, + BSS_CHANGED_QOS = 1<<13, + BSS_CHANGED_IDLE = 1<<14, + BSS_CHANGED_SSID = 1<<15, + BSS_CHANGED_AP_PROBE_RESP = 1<<16, + BSS_CHANGED_PS = 1<<17, + BSS_CHANGED_TXPOWER = 1<<18, + BSS_CHANGED_P2P_PS = 1<<19, + BSS_CHANGED_DTIM_PERIOD = 1<<20, + BSS_CHANGED_BANDWIDTH = 1<<21, + + /* when adding here, make sure to change ieee80211_reconfig */ +}; + +/* + * The maximum number of IPv4 addresses listed for ARP filtering. If the number + * of addresses for an interface increase beyond this value, hardware ARP + * filtering will be disabled. + */ +#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4 + +/** + * enum ieee80211_rssi_event - RSSI threshold event + * An indicator for when RSSI goes below/above a certain threshold. + * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver. + * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver. + */ +enum ieee80211_rssi_event { + RSSI_EVENT_HIGH, + RSSI_EVENT_LOW, +}; + +/** + * struct ieee80211_bss_conf - holds the BSS's changing parameters + * + * This structure keeps information about a BSS (and an association + * to that BSS) that can change during the lifetime of the BSS. + * + * @assoc: association status + * @ibss_joined: indicates whether this station is part of an IBSS + * or not + * @ibss_creator: indicates if a new IBSS network is being created + * @aid: association ID number, valid only when @assoc is true + * @use_cts_prot: use CTS protection + * @use_short_preamble: use 802.11b short preamble; + * if the hardware cannot handle this it must set the + * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag + * @use_short_slot: use short slot time (only relevant for ERP); + * if the hardware cannot handle this it must set the + * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag + * @dtim_period: num of beacons before the next DTIM, for beaconing, + * valid in station mode only if after the driver was notified + * with the %BSS_CHANGED_DTIM_PERIOD flag, will be non-zero then. + * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old + * as it may have been received during scanning long ago). If the + * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can + * only come from a beacon, but might not become valid until after + * association when a beacon is received (which is notified with the + * %BSS_CHANGED_DTIM flag.) + * @sync_device_ts: the device timestamp corresponding to the sync_tsf, + * the driver/device can use this to calculate synchronisation + * (see @sync_tsf) + * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY + * is requested, see @sync_tsf/@sync_device_ts. + * @beacon_int: beacon interval + * @assoc_capability: capabilities taken from assoc resp + * @basic_rates: bitmap of basic rates, each bit stands for an + * index into the rate table configured by the driver in + * the current band. + * @mcast_rate: per-band multicast rate index + 1 (0: disabled) + * @bssid: The BSSID for this BSS + * @enable_beacon: whether beaconing should be enabled or not + * @chandef: Channel definition for this BSS -- the hardware might be + * configured a higher bandwidth than this BSS uses, for example. + * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation. + * This field is only valid when the channel type is one of the HT types. + * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value + * implies disabled + * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis + * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The + * may filter ARP queries targeted for other addresses than listed here. + * The driver must allow ARP queries targeted for all address listed here + * to pass through. An empty list implies no ARP queries need to pass. + * @arp_addr_cnt: Number of addresses currently on the list. Note that this + * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list + * array size), it's up to the driver what to do in that case. + * @qos: This is a QoS-enabled BSS. + * @idle: This interface is idle. There's also a global idle flag in the + * hardware config which may be more appropriate depending on what + * your driver/device needs to do. + * @ps: power-save mode (STA only). This flag is NOT affected by + * offchannel/dynamic_ps operations. + * @ssid: The SSID of the current vif. Valid in AP and IBSS mode. + * @ssid_len: Length of SSID given in @ssid. + * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode. + * @txpower: TX power in dBm + * @p2p_noa_attr: P2P NoA attribute for P2P powersave + */ +struct ieee80211_bss_conf { + const u8 *bssid; + /* association related data */ + bool assoc, ibss_joined; + bool ibss_creator; + u16 aid; + /* erp related data */ + bool use_cts_prot; + bool use_short_preamble; + bool use_short_slot; + bool enable_beacon; + u8 dtim_period; + u16 beacon_int; + u16 assoc_capability; + u64 sync_tsf; + u32 sync_device_ts; + u8 sync_dtim_count; + u32 basic_rates; + int mcast_rate[IEEE80211_NUM_BANDS]; + u16 ht_operation_mode; + s32 cqm_rssi_thold; + u32 cqm_rssi_hyst; + struct cfg80211_chan_def chandef; + __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN]; + int arp_addr_cnt; + bool qos; + bool idle; + bool ps; + u8 ssid[IEEE80211_MAX_SSID_LEN]; + size_t ssid_len; + bool hidden_ssid; + int txpower; + struct ieee80211_p2p_noa_attr p2p_noa_attr; +}; + +/** + * enum mac80211_tx_control_flags - flags to describe transmission information/status + * + * These flags are used with the @flags member of &ieee80211_tx_info. + * + * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame. + * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence + * number to this frame, taking care of not overwriting the fragment + * number and increasing the sequence number only when the + * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly + * assign sequence numbers to QoS-data frames but cannot do so correctly + * for non-QoS-data and management frames because beacons need them from + * that counter as well and mac80211 cannot guarantee proper sequencing. + * If this flag is set, the driver should instruct the hardware to + * assign a sequence number to the frame or assign one itself. Cf. IEEE + * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for + * beacons and always be clear for frames without a sequence number field. + * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack + * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination + * station + * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame + * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon + * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU + * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211. + * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted + * because the destination STA was in powersave mode. Note that to + * avoid race conditions, the filter must be set by the hardware or + * firmware upon receiving a frame that indicates that the station + * went to sleep (must be done on device to filter frames already on + * the queue) and may only be unset after mac80211 gives the OK for + * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above), + * since only then is it guaranteed that no more frames are in the + * hardware queue. + * @IEEE80211_TX_STAT_ACK: Frame was acknowledged + * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status + * is for the whole aggregation. + * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned, + * so consider using block ack request (BAR). + * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be + * set by rate control algorithms to indicate probe rate, will + * be cleared for fragmented frames (except on the last fragment) + * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate + * that a frame can be transmitted while the queues are stopped for + * off-channel operation. + * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211, + * used to indicate that a pending frame requires TX processing before + * it can be sent out. + * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211, + * used to indicate that a frame was already retried due to PS + * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211, + * used to indicate frame should not be encrypted + * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll + * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must + * be sent although the station is in powersave mode. + * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the + * transmit function after the current frame, this can be used + * by drivers to kick the DMA queue only if unset or when the + * queue gets full. + * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted + * after TX status because the destination was asleep, it must not + * be modified again (no seqno assignment, crypto, etc.) + * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME + * code for connection establishment, this indicates that its status + * should kick the MLME state machine. + * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 + * MLME command (internal to mac80211 to figure out whether to send TX + * status to user space) + * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame + * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this + * frame and selects the maximum number of streams that it can use. + * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on + * the off-channel channel when a remain-on-channel offload is done + * in hardware -- normal packets still flow and are expected to be + * handled properly by the device. + * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP + * testing. It will be sent out with incorrect Michael MIC key to allow + * TKIP countermeasures to be tested. + * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate. + * This flag is actually used for management frame especially for P2P + * frames not being sent at CCK rate in 2GHz band. + * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period, + * when its status is reported the service period ends. For frames in + * an SP that mac80211 transmits, it is already set; for driver frames + * the driver may set this flag. It is also used to do the same for + * PS-Poll responses. + * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate. + * This flag is used to send nullfunc frame at minimum rate when + * the nullfunc is used for connection monitoring purpose. + * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it + * would be fragmented by size (this is optional, only used for + * monitor injection). + * + * Note: If you have to add new flags to the enumeration, then don't + * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. + */ +enum mac80211_tx_control_flags { + IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), + IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1), + IEEE80211_TX_CTL_NO_ACK = BIT(2), + IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3), + IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4), + IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5), + IEEE80211_TX_CTL_AMPDU = BIT(6), + IEEE80211_TX_CTL_INJECTED = BIT(7), + IEEE80211_TX_STAT_TX_FILTERED = BIT(8), + IEEE80211_TX_STAT_ACK = BIT(9), + IEEE80211_TX_STAT_AMPDU = BIT(10), + IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), + IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), + IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13), + IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14), + IEEE80211_TX_INTFL_RETRIED = BIT(15), + IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), + IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17), + IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), + IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), + IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20), + IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), + IEEE80211_TX_CTL_LDPC = BIT(22), + IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), + IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25), + IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26), + IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27), + IEEE80211_TX_STATUS_EOSP = BIT(28), + IEEE80211_TX_CTL_USE_MINRATE = BIT(29), + IEEE80211_TX_CTL_DONTFRAG = BIT(30), +}; + +#define IEEE80211_TX_CTL_STBC_SHIFT 23 + +/* + * This definition is used as a mask to clear all temporary flags, which are + * set by the tx handlers for each transmission attempt by the mac80211 stack. + */ +#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \ + IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \ + IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \ + IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \ + IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \ + IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \ + IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \ + IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP) + +/** + * enum mac80211_rate_control_flags - per-rate flags set by the + * Rate Control algorithm. + * + * These flags are set by the Rate control algorithm for each rate during tx, + * in the @flags member of struct ieee80211_tx_rate. + * + * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate. + * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required. + * This is set if the current BSS requires ERP protection. + * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble. + * @IEEE80211_TX_RC_MCS: HT rate. + * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split + * into a higher 4 bits (Nss) and lower 4 bits (MCS number) + * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in + * Greenfield mode. + * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz. + * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission + * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission + * (80+80 isn't supported yet) + * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the + * adjacent 20 MHz channels, if the current channel type is + * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS. + * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate. + */ +enum mac80211_rate_control_flags { + IEEE80211_TX_RC_USE_RTS_CTS = BIT(0), + IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1), + IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2), + + /* rate index is an HT/VHT MCS instead of an index */ + IEEE80211_TX_RC_MCS = BIT(3), + IEEE80211_TX_RC_GREEN_FIELD = BIT(4), + IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5), + IEEE80211_TX_RC_DUP_DATA = BIT(6), + IEEE80211_TX_RC_SHORT_GI = BIT(7), + IEEE80211_TX_RC_VHT_MCS = BIT(8), + IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9), + IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10), +}; + + +/* there are 40 bytes if you don't need the rateset to be kept */ +#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40 + +/* if you do need the rateset, then you have less space */ +#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24 + +/* maximum number of rate stages */ +#define IEEE80211_TX_MAX_RATES 4 + +/* maximum number of rate table entries */ +#define IEEE80211_TX_RATE_TABLE_SIZE 4 + +/** + * struct ieee80211_tx_rate - rate selection/status + * + * @idx: rate index to attempt to send with + * @flags: rate control flags (&enum mac80211_rate_control_flags) + * @count: number of tries in this rate before going to the next rate + * + * A value of -1 for @idx indicates an invalid rate and, if used + * in an array of retry rates, that no more rates should be tried. + * + * When used for transmit status reporting, the driver should + * always report the rate along with the flags it used. + * + * &struct ieee80211_tx_info contains an array of these structs + * in the control information, and it will be filled by the rate + * control algorithm according to what should be sent. For example, + * if this array contains, in the format { <idx>, <count> } the + * information + * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 } + * then this means that the frame should be transmitted + * up to twice at rate 3, up to twice at rate 2, and up to four + * times at rate 1 if it doesn't get acknowledged. Say it gets + * acknowledged by the peer after the fifth attempt, the status + * information should then contain + * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ... + * since it was transmitted twice at rate 3, twice at rate 2 + * and once at rate 1 after which we received an acknowledgement. + */ +struct ieee80211_tx_rate { + s8 idx; + u16 count:5, + flags:11; +} __packed; + +#define IEEE80211_MAX_TX_RETRY 31 + +static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate, + u8 mcs, u8 nss) +{ + WARN_ON(mcs & ~0xF); + WARN_ON((nss - 1) & ~0x7); + rate->idx = ((nss - 1) << 4) | mcs; +} + +static inline u8 +ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate) +{ + return rate->idx & 0xF; +} + +static inline u8 +ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate) +{ + return (rate->idx >> 4) + 1; +} + +/** + * struct ieee80211_tx_info - skb transmit information + * + * This structure is placed in skb->cb for three uses: + * (1) mac80211 TX control - mac80211 tells the driver what to do + * (2) driver internal use (if applicable) + * (3) TX status information - driver tells mac80211 what happened + * + * @flags: transmit info flags, defined above + * @band: the band to transmit on (use for checking for races) + * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC + * @ack_frame_id: internal frame ID for TX status, used internally + * @control: union for control data + * @status: union for status data + * @driver_data: array of driver_data pointers + * @ampdu_ack_len: number of acked aggregated frames. + * relevant only if IEEE80211_TX_STAT_AMPDU was set. + * @ampdu_len: number of aggregated frames. + * relevant only if IEEE80211_TX_STAT_AMPDU was set. + * @ack_signal: signal strength of the ACK frame + */ +struct ieee80211_tx_info { + /* common information */ + u32 flags; + u8 band; + + u8 hw_queue; + + u16 ack_frame_id; + + union { + struct { + union { + /* rate control */ + struct { + struct ieee80211_tx_rate rates[ + IEEE80211_TX_MAX_RATES]; + s8 rts_cts_rate_idx; + u8 use_rts:1; + u8 use_cts_prot:1; + u8 short_preamble:1; + u8 skip_table:1; + /* 2 bytes free */ + }; + /* only needed before rate control */ + unsigned long jiffies; + }; + /* NB: vif can be NULL for injected frames */ + struct ieee80211_vif *vif; + struct ieee80211_key_conf *hw_key; + /* 8 bytes free */ + } control; + struct { + struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; + int ack_signal; + u8 ampdu_ack_len; + u8 ampdu_len; + u8 antenna; + /* 21 bytes free */ + } status; + struct { + struct ieee80211_tx_rate driver_rates[ + IEEE80211_TX_MAX_RATES]; + u8 pad[4]; + + void *rate_driver_data[ + IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)]; + }; + void *driver_data[ + IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)]; + }; +}; + +/** + * struct ieee80211_sched_scan_ies - scheduled scan IEs + * + * This structure is used to pass the appropriate IEs to be used in scheduled + * scans for all bands. It contains both the IEs passed from the userspace + * and the ones generated by mac80211. + * + * @ie: array with the IEs for each supported band + * @len: array with the total length of the IEs for each band + */ +struct ieee80211_sched_scan_ies { + u8 *ie[IEEE80211_NUM_BANDS]; + size_t len[IEEE80211_NUM_BANDS]; +}; + +static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb) +{ + return (struct ieee80211_tx_info *)skb->cb; +} + +static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb) +{ + return (struct ieee80211_rx_status *)skb->cb; +} + +/** + * ieee80211_tx_info_clear_status - clear TX status + * + * @info: The &struct ieee80211_tx_info to be cleared. + * + * When the driver passes an skb back to mac80211, it must report + * a number of things in TX status. This function clears everything + * in the TX status but the rate control information (it does clear + * the count since you need to fill that in anyway). + * + * NOTE: You can only use this function if you do NOT use + * info->driver_data! Use info->rate_driver_data + * instead if you need only the less space that allows. + */ +static inline void +ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) +{ + int i; + + BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != + offsetof(struct ieee80211_tx_info, control.rates)); + BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != + offsetof(struct ieee80211_tx_info, driver_rates)); + BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8); + /* clear the rate counts */ + for (i = 0; i < IEEE80211_TX_MAX_RATES; i++) + info->status.rates[i].count = 0; + + BUILD_BUG_ON( + offsetof(struct ieee80211_tx_info, status.ack_signal) != 20); + memset(&info->status.ampdu_ack_len, 0, + sizeof(struct ieee80211_tx_info) - + offsetof(struct ieee80211_tx_info, status.ampdu_ack_len)); +} + + +/** + * enum mac80211_rx_flags - receive flags + * + * These flags are used with the @flag member of &struct ieee80211_rx_status. + * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. + * Use together with %RX_FLAG_MMIC_STRIPPED. + * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. + * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, + * verification has been done by the hardware. + * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. + * If this flag is set, the stack cannot do any replay detection + * hence the driver or hardware will have to do that. + * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on + * the frame. + * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on + * the frame. + * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime + * field) is valid and contains the time the first symbol of the MPDU + * was received. This is useful in monitor mode and for proper IBSS + * merging. + * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime + * field) is valid and contains the time the last symbol of the MPDU + * (including FCS) was received. + * @RX_FLAG_SHORTPRE: Short preamble was used for this frame + * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index + * @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index + * @RX_FLAG_40MHZ: HT40 (40 MHz) was used + * @RX_FLAG_80MHZ: 80 MHz was used + * @RX_FLAG_80P80MHZ: 80+80 MHz was used + * @RX_FLAG_160MHZ: 160 MHz was used + * @RX_FLAG_SHORT_GI: Short guard interval was used + * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present. + * Valid only for data frames (mainly A-MPDU) + * @RX_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, if + * the driver fills this value it should add %IEEE80211_RADIOTAP_MCS_HAVE_FMT + * to hw.radiotap_mcs_details to advertise that fact + * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference + * number (@ampdu_reference) must be populated and be a distinct number for + * each A-MPDU + * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes + * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for + * monitoring purposes only + * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all + * subframes of a single A-MPDU + * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU + * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected + * on this subframe + * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC + * is stored in the @ampdu_delimiter_crc field) + */ +enum mac80211_rx_flags { + RX_FLAG_MMIC_ERROR = BIT(0), + RX_FLAG_DECRYPTED = BIT(1), + RX_FLAG_MMIC_STRIPPED = BIT(3), + RX_FLAG_IV_STRIPPED = BIT(4), + RX_FLAG_FAILED_FCS_CRC = BIT(5), + RX_FLAG_FAILED_PLCP_CRC = BIT(6), + RX_FLAG_MACTIME_START = BIT(7), + RX_FLAG_SHORTPRE = BIT(8), + RX_FLAG_HT = BIT(9), + RX_FLAG_40MHZ = BIT(10), + RX_FLAG_SHORT_GI = BIT(11), + RX_FLAG_NO_SIGNAL_VAL = BIT(12), + RX_FLAG_HT_GF = BIT(13), + RX_FLAG_AMPDU_DETAILS = BIT(14), + RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15), + RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16), + RX_FLAG_AMPDU_LAST_KNOWN = BIT(17), + RX_FLAG_AMPDU_IS_LAST = BIT(18), + RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19), + RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20), + RX_FLAG_MACTIME_END = BIT(21), + RX_FLAG_VHT = BIT(22), + RX_FLAG_80MHZ = BIT(23), + RX_FLAG_80P80MHZ = BIT(24), + RX_FLAG_160MHZ = BIT(25), +}; + +/** + * struct ieee80211_rx_status - receive status + * + * The low-level driver should provide this information (the subset + * supported by hardware) to the 802.11 code with each received + * frame, in the skb's control buffer (cb). + * + * @mactime: value in microseconds of the 64-bit Time Synchronization Function + * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. + * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use + * it but can store it and pass it back to the driver for synchronisation + * @band: the active band when this frame was received + * @freq: frequency the radio was tuned to when receiving this frame, in MHz + * @signal: signal strength when receiving this frame, either in dBm, in dB or + * unspecified depending on the hardware capabilities flags + * @IEEE80211_HW_SIGNAL_* + * @antenna: antenna used + * @rate_idx: index of data rate into band's supported rates or MCS index if + * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT) + * @vht_nss: number of streams (VHT only) + * @flag: %RX_FLAG_* + * @rx_flags: internal RX flags for mac80211 + * @ampdu_reference: A-MPDU reference number, must be a different value for + * each A-MPDU but the same for each subframe within one A-MPDU + * @ampdu_delimiter_crc: A-MPDU delimiter CRC + * @vendor_radiotap_bitmap: radiotap vendor namespace presence bitmap + * @vendor_radiotap_len: radiotap vendor namespace length + * @vendor_radiotap_align: radiotap vendor namespace alignment. Note + * that the actual data must be at the start of the SKB data + * already. + * @vendor_radiotap_oui: radiotap vendor namespace OUI + * @vendor_radiotap_subns: radiotap vendor sub namespace + */ +struct ieee80211_rx_status { + u64 mactime; + u32 device_timestamp; + u32 ampdu_reference; + u32 flag; + u32 vendor_radiotap_bitmap; + u16 vendor_radiotap_len; + u16 freq; + u8 rate_idx; + u8 vht_nss; + u8 rx_flags; + u8 band; + u8 antenna; + s8 signal; + u8 ampdu_delimiter_crc; + u8 vendor_radiotap_align; + u8 vendor_radiotap_oui[3]; + u8 vendor_radiotap_subns; +}; + +/** + * enum ieee80211_conf_flags - configuration flags + * + * Flags to define PHY configuration options + * + * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this + * to determine for example whether to calculate timestamps for packets + * or not, do not use instead of filter flags! + * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only). + * This is the power save mode defined by IEEE 802.11-2007 section 11.2, + * meaning that the hardware still wakes up for beacons, is able to + * transmit frames and receive the possible acknowledgment frames. + * Not to be confused with hardware specific wakeup/sleep states, + * driver is responsible for that. See the section "Powersave support" + * for more. + * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set + * the driver should be prepared to handle configuration requests but + * may turn the device off as much as possible. Typically, this flag will + * be set when an interface is set UP but not associated or scanning, but + * it can also be unset in that case when monitor interfaces are active. + * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main + * operating channel. + */ +enum ieee80211_conf_flags { + IEEE80211_CONF_MONITOR = (1<<0), + IEEE80211_CONF_PS = (1<<1), + IEEE80211_CONF_IDLE = (1<<2), + IEEE80211_CONF_OFFCHANNEL = (1<<3), +}; + + +/** + * enum ieee80211_conf_changed - denotes which configuration changed + * + * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed + * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed + * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed + * @IEEE80211_CONF_CHANGE_POWER: the TX power changed + * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed + * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed + * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed + * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed + * Note that this is only valid if channel contexts are not used, + * otherwise each channel context has the number of chains listed. + */ +enum ieee80211_conf_changed { + IEEE80211_CONF_CHANGE_SMPS = BIT(1), + IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), + IEEE80211_CONF_CHANGE_MONITOR = BIT(3), + IEEE80211_CONF_CHANGE_PS = BIT(4), + IEEE80211_CONF_CHANGE_POWER = BIT(5), + IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), + IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7), + IEEE80211_CONF_CHANGE_IDLE = BIT(8), +}; + +/** + * enum ieee80211_smps_mode - spatial multiplexing power save mode + * + * @IEEE80211_SMPS_AUTOMATIC: automatic + * @IEEE80211_SMPS_OFF: off + * @IEEE80211_SMPS_STATIC: static + * @IEEE80211_SMPS_DYNAMIC: dynamic + * @IEEE80211_SMPS_NUM_MODES: internal, don't use + */ +enum ieee80211_smps_mode { + IEEE80211_SMPS_AUTOMATIC, + IEEE80211_SMPS_OFF, + IEEE80211_SMPS_STATIC, + IEEE80211_SMPS_DYNAMIC, + + /* keep last */ + IEEE80211_SMPS_NUM_MODES, +}; + +/** + * struct ieee80211_conf - configuration of the device + * + * This struct indicates how the driver shall configure the hardware. + * + * @flags: configuration flags defined above + * + * @listen_interval: listen interval in units of beacon interval + * @max_sleep_period: the maximum number of beacon intervals to sleep for + * before checking the beacon for a TIM bit (managed mode only); this + * value will be only achievable between DTIM frames, the hardware + * needs to check for the multicast traffic bit in DTIM beacons. + * This variable is valid only when the CONF_PS flag is set. + * @ps_dtim_period: The DTIM period of the AP we're connected to, for use + * in power saving. Power saving will not be enabled until a beacon + * has been received and the DTIM period is known. + * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the + * powersave documentation below. This variable is valid only when + * the CONF_PS flag is set. + * + * @power_level: requested transmit power (in dBm), backward compatibility + * value only that is set to the minimum of all interfaces + * + * @chandef: the channel definition to tune to + * @radar_enabled: whether radar detection is enabled + * + * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame + * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, + * but actually means the number of transmissions not the number of retries + * @short_frame_max_tx_count: Maximum number of transmissions for a "short" + * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the + * number of transmissions not the number of retries + * + * @smps_mode: spatial multiplexing powersave mode; note that + * %IEEE80211_SMPS_STATIC is used when the device is not + * configured for an HT channel. + * Note that this is only valid if channel contexts are not used, + * otherwise each channel context has the number of chains listed. + */ +struct ieee80211_conf { + u32 flags; + int power_level, dynamic_ps_timeout; + int max_sleep_period; + + u16 listen_interval; + u8 ps_dtim_period; + + u8 long_frame_max_tx_count, short_frame_max_tx_count; + + struct cfg80211_chan_def chandef; + bool radar_enabled; + enum ieee80211_smps_mode smps_mode; +}; + +/** + * struct ieee80211_channel_switch - holds the channel switch data + * + * The information provided in this structure is required for channel switch + * operation. + * + * @timestamp: value in microseconds of the 64-bit Time Synchronization + * Function (TSF) timer when the frame containing the channel switch + * announcement was received. This is simply the rx.mactime parameter + * the driver passed into mac80211. + * @block_tx: Indicates whether transmission must be blocked before the + * scheduled channel switch, as indicated by the AP. + * @chandef: the new channel to switch to + * @count: the number of TBTT's until the channel switch event + */ +struct ieee80211_channel_switch { + u64 timestamp; + bool block_tx; + struct cfg80211_chan_def chandef; + u8 count; +}; + +/** + * enum ieee80211_vif_flags - virtual interface flags + * + * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering + * on this virtual interface to avoid unnecessary CPU wakeups + * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality + * monitoring on this virtual interface -- i.e. it can monitor + * connection quality related parameters, such as the RSSI level and + * provide notifications if configured trigger levels are reached. + */ +enum ieee80211_vif_flags { + IEEE80211_VIF_BEACON_FILTER = BIT(0), + IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1), +}; + +/** + * struct ieee80211_vif - per-interface data + * + * Data in this structure is continually present for driver + * use during the life of a virtual interface. + * + * @type: type of this virtual interface + * @bss_conf: BSS configuration for this interface, either our own + * or the BSS we're associated to + * @addr: address of this interface + * @p2p: indicates whether this AP or STA interface is a p2p + * interface, i.e. a GO or p2p-sta respectively + * @driver_flags: flags/capabilities the driver has for this interface, + * these need to be set (or cleared) when the interface is added + * or, if supported by the driver, the interface type is changed + * at runtime, mac80211 will never touch this field + * @hw_queue: hardware queue for each AC + * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only + * @chanctx_conf: The channel context this interface is assigned to, or %NULL + * when it is not assigned. This pointer is RCU-protected due to the TX + * path needing to access it; even though the netdev carrier will always + * be off when it is %NULL there can still be races and packets could be + * processed after it switches back to %NULL. + * @debugfs_dir: debugfs dentry, can be used by drivers to create own per + * interface debug files. Note that it will be NULL for the virtual + * monitor interface (if that is requested.) + * @drv_priv: data area for driver use, will always be aligned to + * sizeof(void *). + */ +struct ieee80211_vif { + enum nl80211_iftype type; + struct ieee80211_bss_conf bss_conf; + u8 addr[ETH_ALEN]; + bool p2p; + + u8 cab_queue; + u8 hw_queue[IEEE80211_NUM_ACS]; + + struct ieee80211_chanctx_conf __rcu *chanctx_conf; + + u32 driver_flags; + +#ifdef CPTCFG_MAC80211_DEBUGFS + struct dentry *debugfs_dir; +#endif + + /* must be last */ + u8 drv_priv[0] __aligned(sizeof(void *)); +}; + +static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) +{ +#ifdef CPTCFG_MAC80211_MESH + return vif->type == NL80211_IFTYPE_MESH_POINT; +#endif + return false; +} + +/** + * enum ieee80211_key_flags - key flags + * + * These flags are used for communication about keys between the driver + * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. + * + * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the + * driver to indicate that it requires IV generation for this + * particular key. + * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by + * the driver for a TKIP key if it requires Michael MIC + * generation in software. + * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates + * that the key is pairwise rather then a shared key. + * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a + * CCMP key if it requires CCMP encryption of management frames (MFP) to + * be done in software. + * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver + * if space should be prepared for the IV, but the IV + * itself should not be generated. Do not set together with + * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. + * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received + * management frames. The flag can help drivers that have a hardware + * crypto implementation that doesn't deal with management frames + * properly by allowing them to not upload the keys to hardware and + * fall back to software crypto. Note that this flag deals only with + * RX, if your crypto engine can't deal with TX you can also set the + * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW. + */ +enum ieee80211_key_flags { + IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, + IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, + IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, + IEEE80211_KEY_FLAG_SW_MGMT_TX = 1<<4, + IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5, + IEEE80211_KEY_FLAG_RX_MGMT = 1<<6, +}; + +/** + * struct ieee80211_key_conf - key information + * + * This key information is given by mac80211 to the driver by + * the set_key() callback in &struct ieee80211_ops. + * + * @hw_key_idx: To be set by the driver, this is the key index the driver + * wants to be given when a frame is transmitted and needs to be + * encrypted in hardware. + * @cipher: The key's cipher suite selector. + * @flags: key flags, see &enum ieee80211_key_flags. + * @keyidx: the key index (0-3) + * @keylen: key material length + * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte) + * data block: + * - Temporal Encryption Key (128 bits) + * - Temporal Authenticator Tx MIC Key (64 bits) + * - Temporal Authenticator Rx MIC Key (64 bits) + * @icv_len: The ICV length for this key type + * @iv_len: The IV length for this key type + */ +struct ieee80211_key_conf { + u32 cipher; + u8 icv_len; + u8 iv_len; + u8 hw_key_idx; + u8 flags; + s8 keyidx; + u8 keylen; + u8 key[0]; +}; + +/** + * enum set_key_cmd - key command + * + * Used with the set_key() callback in &struct ieee80211_ops, this + * indicates whether a key is being removed or added. + * + * @SET_KEY: a key is set + * @DISABLE_KEY: a key must be disabled + */ +enum set_key_cmd { + SET_KEY, DISABLE_KEY, +}; + +/** + * enum ieee80211_sta_state - station state + * + * @IEEE80211_STA_NOTEXIST: station doesn't exist at all, + * this is a special state for add/remove transitions + * @IEEE80211_STA_NONE: station exists without special state + * @IEEE80211_STA_AUTH: station is authenticated + * @IEEE80211_STA_ASSOC: station is associated + * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X) + */ +enum ieee80211_sta_state { + /* NOTE: These need to be ordered correctly! */ + IEEE80211_STA_NOTEXIST, + IEEE80211_STA_NONE, + IEEE80211_STA_AUTH, + IEEE80211_STA_ASSOC, + IEEE80211_STA_AUTHORIZED, +}; + +/** + * enum ieee80211_sta_rx_bandwidth - station RX bandwidth + * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz + * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz + * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz + * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz + * (including 80+80 MHz) + * + * Implementation note: 20 must be zero to be initialized + * correctly, the values must be sorted. + */ +enum ieee80211_sta_rx_bandwidth { + IEEE80211_STA_RX_BW_20 = 0, + IEEE80211_STA_RX_BW_40, + IEEE80211_STA_RX_BW_80, + IEEE80211_STA_RX_BW_160, +}; + +/** + * struct ieee80211_sta_rates - station rate selection table + * + * @rcu_head: RCU head used for freeing the table on update + * @rates: transmit rates/flags to be used by default. + * Overriding entries per-packet is possible by using cb tx control. + */ +struct ieee80211_sta_rates { + struct rcu_head rcu_head; + struct { + s8 idx; + u8 count; + u8 count_cts; + u8 count_rts; + u16 flags; + } rate[IEEE80211_TX_RATE_TABLE_SIZE]; +}; + +/** + * struct ieee80211_sta - station table entry + * + * A station table entry represents a station we are possibly + * communicating with. Since stations are RCU-managed in + * mac80211, any ieee80211_sta pointer you get access to must + * either be protected by rcu_read_lock() explicitly or implicitly, + * or you must take good care to not use such a pointer after a + * call to your sta_remove callback that removed it. + * + * @addr: MAC address + * @aid: AID we assigned to the station if we're an AP + * @supp_rates: Bitmap of supported rates (per band) + * @ht_cap: HT capabilities of this STA; restricted to our own capabilities + * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities + * @wme: indicates whether the STA supports WME. Only valid during AP-mode. + * @drv_priv: data area for driver use, will always be aligned to + * sizeof(void *), size is determined in hw information. + * @uapsd_queues: bitmap of queues configured for uapsd. Only valid + * if wme is supported. + * @max_sp: max Service Period. Only valid if wme is supported. + * @bandwidth: current bandwidth the station can receive with + * @rx_nss: in HT/VHT, the maximum number of spatial streams the + * station can receive at the moment, changed by operating mode + * notifications and capabilities. The value is only valid after + * the station moves to associated state. + * @smps_mode: current SMPS mode (off, static or dynamic) + * @tx_rates: rate control selection table + */ +struct ieee80211_sta { + u32 supp_rates[IEEE80211_NUM_BANDS]; + u8 addr[ETH_ALEN]; + u16 aid; + struct ieee80211_sta_ht_cap ht_cap; + struct ieee80211_sta_vht_cap vht_cap; + bool wme; + u8 uapsd_queues; + u8 max_sp; + u8 rx_nss; + enum ieee80211_sta_rx_bandwidth bandwidth; + enum ieee80211_smps_mode smps_mode; + struct ieee80211_sta_rates __rcu *rates; + + /* must be last */ + u8 drv_priv[0] __aligned(sizeof(void *)); +}; + +/** + * enum sta_notify_cmd - sta notify command + * + * Used with the sta_notify() callback in &struct ieee80211_ops, this + * indicates if an associated station made a power state transition. + * + * @STA_NOTIFY_SLEEP: a station is now sleeping + * @STA_NOTIFY_AWAKE: a sleeping station woke up + */ +enum sta_notify_cmd { + STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE, +}; + +/** + * struct ieee80211_tx_control - TX control data + * + * @sta: station table entry, this sta pointer may be NULL and + * it is not allowed to copy the pointer, due to RCU. + */ +struct ieee80211_tx_control { + struct ieee80211_sta *sta; +}; + +/** + * enum ieee80211_hw_flags - hardware flags + * + * These flags are used to indicate hardware capabilities to + * the stack. Generally, flags here should have their meaning + * done in a way that the simplest hardware doesn't need setting + * any particular flags. There are some exceptions to this rule, + * however, so you are advised to review these flags carefully. + * + * @IEEE80211_HW_HAS_RATE_CONTROL: + * The hardware or firmware includes rate control, and cannot be + * controlled by the stack. As such, no rate control algorithm + * should be instantiated, and the TX rate reported to userspace + * will be taken from the TX status instead of the rate control + * algorithm. + * Note that this requires that the driver implement a number of + * callbacks so it has the correct information, it needs to have + * the @set_rts_threshold callback and must look at the BSS config + * @use_cts_prot for G/N protection, @use_short_slot for slot + * timing in 2.4 GHz and @use_short_preamble for preambles for + * CCK frames. + * + * @IEEE80211_HW_RX_INCLUDES_FCS: + * Indicates that received frames passed to the stack include + * the FCS at the end. + * + * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING: + * Some wireless LAN chipsets buffer broadcast/multicast frames + * for power saving stations in the hardware/firmware and others + * rely on the host system for such buffering. This option is used + * to configure the IEEE 802.11 upper layer to buffer broadcast and + * multicast frames when there are power saving stations so that + * the driver can fetch them with ieee80211_get_buffered_bc(). + * + * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: + * Hardware is not capable of short slot operation on the 2.4 GHz band. + * + * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: + * Hardware is not capable of receiving frames with short preamble on + * the 2.4 GHz band. + * + * @IEEE80211_HW_SIGNAL_UNSPEC: + * Hardware can provide signal values but we don't know its units. We + * expect values between 0 and @max_signal. + * If possible please provide dB or dBm instead. + * + * @IEEE80211_HW_SIGNAL_DBM: + * Hardware gives signal values in dBm, decibel difference from + * one milliwatt. This is the preferred method since it is standardized + * between different devices. @max_signal does not need to be set. + * + * @IEEE80211_HW_SPECTRUM_MGMT: + * Hardware supports spectrum management defined in 802.11h + * Measurement, Channel Switch, Quieting, TPC + * + * @IEEE80211_HW_AMPDU_AGGREGATION: + * Hardware supports 11n A-MPDU aggregation. + * + * @IEEE80211_HW_SUPPORTS_PS: + * Hardware has power save support (i.e. can go to sleep). + * + * @IEEE80211_HW_PS_NULLFUNC_STACK: + * Hardware requires nullfunc frame handling in stack, implies + * stack support for dynamic PS. + * + * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS: + * Hardware has support for dynamic PS. + * + * @IEEE80211_HW_MFP_CAPABLE: + * Hardware supports management frame protection (MFP, IEEE 802.11w). + * + * @IEEE80211_HW_SUPPORTS_STATIC_SMPS: + * Hardware supports static spatial multiplexing powersave, + * ie. can turn off all but one chain even on HT connections + * that should be using more chains. + * + * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS: + * Hardware supports dynamic spatial multiplexing powersave, + * ie. can turn off all but one chain and then wake the rest + * up as required after, for example, rts/cts handshake. + * + * @IEEE80211_HW_SUPPORTS_UAPSD: + * Hardware supports Unscheduled Automatic Power Save Delivery + * (U-APSD) in managed mode. The mode is configured with + * conf_tx() operation. + * + * @IEEE80211_HW_REPORTS_TX_ACK_STATUS: + * Hardware can provide ack status reports of Tx frames to + * the stack. + * + * @IEEE80211_HW_CONNECTION_MONITOR: + * The hardware performs its own connection monitoring, including + * periodic keep-alives to the AP and probing the AP on beacon loss. + * When this flag is set, signaling beacon-loss will cause an immediate + * change to disassociated state. + * + * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: + * This device needs to get data from beacon before association (i.e. + * dtim_period). + * + * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports + * per-station GTKs as used by IBSS RSN or during fast transition. If + * the device doesn't support per-station GTKs, but can be asked not + * to decrypt group addressed frames, then IBSS RSN support is still + * possible but software crypto will be used. Advertise the wiphy flag + * only in that case. + * + * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device + * autonomously manages the PS status of connected stations. When + * this flag is set mac80211 will not trigger PS mode for connected + * stations based on the PM bit of incoming frames. + * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure + * the PS mode of connected stations. + * + * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session + * setup strictly in HW. mac80211 should not attempt to do this in + * software. + * + * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of + * a virtual monitor interface when monitor interfaces are the only + * active interfaces. + * + * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface + * queue mapping in order to use different queues (not just one per AC) + * for different virtual interfaces. See the doc section on HW queue + * control for more details. + * + * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate + * selection table provided by the rate control algorithm. + * + * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any + * P2P Interface. This will be honoured even if more than one interface + * is supported. + * + * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames + * only, to allow getting TBTT of a DTIM beacon. + */ +enum ieee80211_hw_flags { + IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, + IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, + IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, + IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, + IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, + IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, + IEEE80211_HW_SIGNAL_DBM = 1<<6, + IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7, + IEEE80211_HW_SPECTRUM_MGMT = 1<<8, + IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, + IEEE80211_HW_SUPPORTS_PS = 1<<10, + IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11, + IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, + IEEE80211_HW_MFP_CAPABLE = 1<<13, + IEEE80211_HW_WANT_MONITOR_VIF = 1<<14, + IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15, + IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16, + IEEE80211_HW_SUPPORTS_UAPSD = 1<<17, + IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, + IEEE80211_HW_CONNECTION_MONITOR = 1<<19, + IEEE80211_HW_QUEUE_CONTROL = 1<<20, + IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, + IEEE80211_HW_AP_LINK_PS = 1<<22, + IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23, + IEEE80211_HW_SUPPORTS_RC_TABLE = 1<<24, + IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, + IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, + IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27, +}; + +/** + * struct ieee80211_hw - hardware information and state + * + * This structure contains the configuration and hardware + * information for an 802.11 PHY. + * + * @wiphy: This points to the &struct wiphy allocated for this + * 802.11 PHY. You must fill in the @perm_addr and @dev + * members of this structure using SET_IEEE80211_DEV() + * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported + * bands (with channels, bitrates) are registered here. + * + * @conf: &struct ieee80211_conf, device configuration, don't use. + * + * @priv: pointer to private area that was allocated for driver use + * along with this structure. + * + * @flags: hardware flags, see &enum ieee80211_hw_flags. + * + * @extra_tx_headroom: headroom to reserve in each transmit skb + * for use by the driver (e.g. for transmit headers.) + * + * @channel_change_time: time (in microseconds) it takes to change channels. + * + * @max_signal: Maximum value for signal (rssi) in RX information, used + * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB + * + * @max_listen_interval: max listen interval in units of beacon interval + * that HW supports + * + * @queues: number of available hardware transmit queues for + * data packets. WMM/QoS requires at least four, these + * queues need to have configurable access parameters. + * + * @rate_control_algorithm: rate control algorithm for this hardware. + * If unset (NULL), the default algorithm will be used. Must be + * set before calling ieee80211_register_hw(). + * + * @vif_data_size: size (in bytes) of the drv_priv data area + * within &struct ieee80211_vif. + * @sta_data_size: size (in bytes) of the drv_priv data area + * within &struct ieee80211_sta. + * @chanctx_data_size: size (in bytes) of the drv_priv data area + * within &struct ieee80211_chanctx_conf. + * + * @max_rates: maximum number of alternate rate retry stages the hw + * can handle. + * @max_report_rates: maximum number of alternate rate retry stages + * the hw can report back. + * @max_rate_tries: maximum number of tries for each stage + * + * @napi_weight: weight used for NAPI polling. You must specify an + * appropriate value here if a napi_poll operation is provided + * by your driver. + * + * @max_rx_aggregation_subframes: maximum buffer size (number of + * sub-frames) to be used for A-MPDU block ack receiver + * aggregation. + * This is only relevant if the device has restrictions on the + * number of subframes, if it relies on mac80211 to do reordering + * it shouldn't be set. + * + * @max_tx_aggregation_subframes: maximum number of subframes in an + * aggregate an HT driver will transmit, used by the peer as a + * hint to size its reorder buffer. + * + * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX + * (if %IEEE80211_HW_QUEUE_CONTROL is set) + * + * @radiotap_mcs_details: lists which MCS information can the HW + * reports, by default it is set to _MCS, _GI and _BW but doesn't + * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_* values, only + * adding _BW is supported today. + * + * @radiotap_vht_details: lists which VHT MCS information the HW reports, + * the default is _GI | _BANDWIDTH. + * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_* values. + * + * @netdev_features: netdev features to be set in each netdev created + * from this HW. Note only HW checksum features are currently + * compatible with mac80211. Other feature bits will be rejected. + * + * @uapsd_queues: This bitmap is included in (re)association frame to indicate + * for each access category if it is uAPSD trigger-enabled and delivery- + * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap. + * Each bit corresponds to different AC. Value '1' in specific bit means + * that corresponding AC is both trigger- and delivery-enabled. '0' means + * neither enabled. + * + * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may + * deliver to a WMM STA during any Service Period triggered by the WMM STA. + * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values. + */ +struct ieee80211_hw { + struct ieee80211_conf conf; + struct wiphy *wiphy; + const char *rate_control_algorithm; + void *priv; + u32 flags; + unsigned int extra_tx_headroom; + int channel_change_time; + int vif_data_size; + int sta_data_size; + int chanctx_data_size; + int napi_weight; + u16 queues; + u16 max_listen_interval; + s8 max_signal; + u8 max_rates; + u8 max_report_rates; + u8 max_rate_tries; + u8 max_rx_aggregation_subframes; + u8 max_tx_aggregation_subframes; + u8 offchannel_tx_hw_queue; + u8 radiotap_mcs_details; + u16 radiotap_vht_details; + netdev_features_t netdev_features; + u8 uapsd_queues; + u8 uapsd_max_sp_len; +}; + +/** + * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy + * + * @wiphy: the &struct wiphy which we want to query + * + * mac80211 drivers can use this to get to their respective + * &struct ieee80211_hw. Drivers wishing to get to their own private + * structure can then access it via hw->priv. Note that mac802111 drivers should + * not use wiphy_priv() to try to get their private driver structure as this + * is already used internally by mac80211. + * + * Return: The mac80211 driver hw struct of @wiphy. + */ +struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); + +/** + * SET_IEEE80211_DEV - set device for 802.11 hardware + * + * @hw: the &struct ieee80211_hw to set the device for + * @dev: the &struct device of this 802.11 device + */ +static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev) +{ + set_wiphy_dev(hw->wiphy, dev); +} + +/** + * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware + * + * @hw: the &struct ieee80211_hw to set the MAC address for + * @addr: the address to set + */ +static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) +{ + memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); +} + +static inline struct ieee80211_rate * +ieee80211_get_tx_rate(const struct ieee80211_hw *hw, + const struct ieee80211_tx_info *c) +{ + if (WARN_ON_ONCE(c->control.rates[0].idx < 0)) + return NULL; + return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx]; +} + +static inline struct ieee80211_rate * +ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw, + const struct ieee80211_tx_info *c) +{ + if (c->control.rts_cts_rate_idx < 0) + return NULL; + return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx]; +} + +static inline struct ieee80211_rate * +ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, + const struct ieee80211_tx_info *c, int idx) +{ + if (c->control.rates[idx + 1].idx < 0) + return NULL; + return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx]; +} + +/** + * ieee80211_free_txskb - free TX skb + * @hw: the hardware + * @skb: the skb + * + * Free a transmit skb. Use this funtion when some failure + * to transmit happened and thus status cannot be reported. + */ +void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); + +/** + * DOC: Hardware crypto acceleration + * + * mac80211 is capable of taking advantage of many hardware + * acceleration designs for encryption and decryption operations. + * + * The set_key() callback in the &struct ieee80211_ops for a given + * device is called to enable hardware acceleration of encryption and + * decryption. The callback takes a @sta parameter that will be NULL + * for default keys or keys used for transmission only, or point to + * the station information for the peer for individual keys. + * Multiple transmission keys with the same key index may be used when + * VLANs are configured for an access point. + * + * When transmitting, the TX control data will use the @hw_key_idx + * selected by the driver by modifying the &struct ieee80211_key_conf + * pointed to by the @key parameter to the set_key() function. + * + * The set_key() call for the %SET_KEY command should return 0 if + * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be + * added; if you return 0 then hw_key_idx must be assigned to the + * hardware key index, you are free to use the full u8 range. + * + * When the cmd is %DISABLE_KEY then it must succeed. + * + * Note that it is permissible to not decrypt a frame even if a key + * for it has been uploaded to hardware, the stack will not make any + * decision based on whether a key has been uploaded or not but rather + * based on the receive flags. + * + * The &struct ieee80211_key_conf structure pointed to by the @key + * parameter is guaranteed to be valid until another call to set_key() + * removes it, but it can only be used as a cookie to differentiate + * keys. + * + * In TKIP some HW need to be provided a phase 1 key, for RX decryption + * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key + * handler. + * The update_tkip_key() call updates the driver with the new phase 1 key. + * This happens every time the iv16 wraps around (every 65536 packets). The + * set_key() call will happen only once for each key (unless the AP did + * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is + * provided by update_tkip_key only. The trigger that makes mac80211 call this + * handler is software decryption with wrap around of iv16. + * + * The set_default_unicast_key() call updates the default WEP key index + * configured to the hardware for WEP encryption type. This is required + * for devices that support offload of data packets (e.g. ARP responses). + */ + +/** + * DOC: Powersave support + * + * mac80211 has support for various powersave implementations. + * + * First, it can support hardware that handles all powersaving by itself, + * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware + * flag. In that case, it will be told about the desired powersave mode + * with the %IEEE80211_CONF_PS flag depending on the association status. + * The hardware must take care of sending nullfunc frames when necessary, + * i.e. when entering and leaving powersave mode. The hardware is required + * to look at the AID in beacons and signal to the AP that it woke up when + * it finds traffic directed to it. + * + * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in + * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused + * with hardware wakeup and sleep states. Driver is responsible for waking + * up the hardware before issuing commands to the hardware and putting it + * back to sleep at appropriate times. + * + * When PS is enabled, hardware needs to wakeup for beacons and receive the + * buffered multicast/broadcast frames after the beacon. Also it must be + * possible to send frames and receive the acknowledment frame. + * + * Other hardware designs cannot send nullfunc frames by themselves and also + * need software support for parsing the TIM bitmap. This is also supported + * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and + * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still + * required to pass up beacons. The hardware is still required to handle + * waking up for multicast traffic; if it cannot the driver must handle that + * as best as it can, mac80211 is too slow to do that. + * + * Dynamic powersave is an extension to normal powersave in which the + * hardware stays awake for a user-specified period of time after sending a + * frame so that reply frames need not be buffered and therefore delayed to + * the next wakeup. It's compromise of getting good enough latency when + * there's data traffic and still saving significantly power in idle + * periods. + * + * Dynamic powersave is simply supported by mac80211 enabling and disabling + * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS + * flag and mac80211 will handle everything automatically. Additionally, + * hardware having support for the dynamic PS feature may set the + * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support + * dynamic PS mode itself. The driver needs to look at the + * @dynamic_ps_timeout hardware configuration value and use it that value + * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable + * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS + * enabled whenever user has enabled powersave. + * + * Driver informs U-APSD client support by enabling + * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the + * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS + * Nullfunc frames and stay awake until the service period has ended. To + * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames + * from that AC are transmitted with powersave enabled. + * + * Note: U-APSD client mode is not yet supported with + * %IEEE80211_HW_PS_NULLFUNC_STACK. + */ + +/** + * DOC: Beacon filter support + * + * Some hardware have beacon filter support to reduce host cpu wakeups + * which will reduce system power consumption. It usually works so that + * the firmware creates a checksum of the beacon but omits all constantly + * changing elements (TSF, TIM etc). Whenever the checksum changes the + * beacon is forwarded to the host, otherwise it will be just dropped. That + * way the host will only receive beacons where some relevant information + * (for example ERP protection or WMM settings) have changed. + * + * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER + * interface capability. The driver needs to enable beacon filter support + * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When + * power save is enabled, the stack will not check for beacon loss and the + * driver needs to notify about loss of beacons with ieee80211_beacon_loss(). + * + * The time (or number of beacons missed) until the firmware notifies the + * driver of a beacon loss event (which in turn causes the driver to call + * ieee80211_beacon_loss()) should be configurable and will be controlled + * by mac80211 and the roaming algorithm in the future. + * + * Since there may be constantly changing information elements that nothing + * in the software stack cares about, we will, in the future, have mac80211 + * tell the driver which information elements are interesting in the sense + * that we want to see changes in them. This will include + * - a list of information element IDs + * - a list of OUIs for the vendor information element + * + * Ideally, the hardware would filter out any beacons without changes in the + * requested elements, but if it cannot support that it may, at the expense + * of some efficiency, filter out only a subset. For example, if the device + * doesn't support checking for OUIs it should pass up all changes in all + * vendor information elements. + * + * Note that change, for the sake of simplification, also includes information + * elements appearing or disappearing from the beacon. + * + * Some hardware supports an "ignore list" instead, just make sure nothing + * that was requested is on the ignore list, and include commonly changing + * information element IDs in the ignore list, for example 11 (BSS load) and + * the various vendor-assigned IEs with unknown contents (128, 129, 133-136, + * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility + * it could also include some currently unused IDs. + * + * + * In addition to these capabilities, hardware should support notifying the + * host of changes in the beacon RSSI. This is relevant to implement roaming + * when no traffic is flowing (when traffic is flowing we see the RSSI of + * the received data packets). This can consist in notifying the host when + * the RSSI changes significantly or when it drops below or rises above + * configurable thresholds. In the future these thresholds will also be + * configured by mac80211 (which gets them from userspace) to implement + * them as the roaming algorithm requires. + * + * If the hardware cannot implement this, the driver should ask it to + * periodically pass beacon frames to the host so that software can do the + * signal strength threshold checking. + */ + +/** + * DOC: Spatial multiplexing power save + * + * SMPS (Spatial multiplexing power save) is a mechanism to conserve + * power in an 802.11n implementation. For details on the mechanism + * and rationale, please refer to 802.11 (as amended by 802.11n-2009) + * "11.2.3 SM power save". + * + * The mac80211 implementation is capable of sending action frames + * to update the AP about the station's SMPS mode, and will instruct + * the driver to enter the specific mode. It will also announce the + * requested SMPS mode during the association handshake. Hardware + * support for this feature is required, and can be indicated by + * hardware flags. + * + * The default mode will be "automatic", which nl80211/cfg80211 + * defines to be dynamic SMPS in (regular) powersave, and SMPS + * turned off otherwise. + * + * To support this feature, the driver must set the appropriate + * hardware support flags, and handle the SMPS flag to the config() + * operation. It will then with this mechanism be instructed to + * enter the requested SMPS mode while associated to an HT AP. + */ + +/** + * DOC: Frame filtering + * + * mac80211 requires to see many management frames for proper + * operation, and users may want to see many more frames when + * in monitor mode. However, for best CPU usage and power consumption, + * having as few frames as possible percolate through the stack is + * desirable. Hence, the hardware should filter as much as possible. + * + * To achieve this, mac80211 uses filter flags (see below) to tell + * the driver's configure_filter() function which frames should be + * passed to mac80211 and which should be filtered out. + * + * Before configure_filter() is invoked, the prepare_multicast() + * callback is invoked with the parameters @mc_count and @mc_list + * for the combined multicast address list of all virtual interfaces. + * It's use is optional, and it returns a u64 that is passed to + * configure_filter(). Additionally, configure_filter() has the + * arguments @changed_flags telling which flags were changed and + * @total_flags with the new flag states. + * + * If your device has no multicast address filters your driver will + * need to check both the %FIF_ALLMULTI flag and the @mc_count + * parameter to see whether multicast frames should be accepted + * or dropped. + * + * All unsupported flags in @total_flags must be cleared. + * Hardware does not support a flag if it is incapable of _passing_ + * the frame to the stack. Otherwise the driver must ignore + * the flag, but not clear it. + * You must _only_ clear the flag (announce no support for the + * flag to mac80211) if you are not able to pass the packet type + * to the stack (so the hardware always filters it). + * So for example, you should clear @FIF_CONTROL, if your hardware + * always filters control frames. If your hardware always passes + * control frames to the kernel and is incapable of filtering them, + * you do _not_ clear the @FIF_CONTROL flag. + * This rule applies to all other FIF flags as well. + */ + +/** + * DOC: AP support for powersaving clients + * + * In order to implement AP and P2P GO modes, mac80211 has support for + * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD. + * There currently is no support for sAPSD. + * + * There is one assumption that mac80211 makes, namely that a client + * will not poll with PS-Poll and trigger with uAPSD at the same time. + * Both are supported, and both can be used by the same client, but + * they can't be used concurrently by the same client. This simplifies + * the driver code. + * + * The first thing to keep in mind is that there is a flag for complete + * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set, + * mac80211 expects the driver to handle most of the state machine for + * powersaving clients and will ignore the PM bit in incoming frames. + * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of + * stations' powersave transitions. In this mode, mac80211 also doesn't + * handle PS-Poll/uAPSD. + * + * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the + * PM bit in incoming frames for client powersave transitions. When a + * station goes to sleep, we will stop transmitting to it. There is, + * however, a race condition: a station might go to sleep while there is + * data buffered on hardware queues. If the device has support for this + * it will reject frames, and the driver should give the frames back to + * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will + * cause mac80211 to retry the frame when the station wakes up. The + * driver is also notified of powersave transitions by calling its + * @sta_notify callback. + * + * When the station is asleep, it has three choices: it can wake up, + * it can PS-Poll, or it can possibly start a uAPSD service period. + * Waking up is implemented by simply transmitting all buffered (and + * filtered) frames to the station. This is the easiest case. When + * the station sends a PS-Poll or a uAPSD trigger frame, mac80211 + * will inform the driver of this with the @allow_buffered_frames + * callback; this callback is optional. mac80211 will then transmit + * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER + * on each frame. The last frame in the service period (or the only + * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to + * indicate that it ends the service period; as this frame must have + * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS. + * When TX status is reported for this frame, the service period is + * marked has having ended and a new one can be started by the peer. + * + * Additionally, non-bufferable MMPDUs can also be transmitted by + * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them. + * + * Another race condition can happen on some devices like iwlwifi + * when there are frames queued for the station and it wakes up + * or polls; the frames that are already queued could end up being + * transmitted first instead, causing reordering and/or wrong + * processing of the EOSP. The cause is that allowing frames to be + * transmitted to a certain station is out-of-band communication to + * the device. To allow this problem to be solved, the driver can + * call ieee80211_sta_block_awake() if frames are buffered when it + * is notified that the station went to sleep. When all these frames + * have been filtered (see above), it must call the function again + * to indicate that the station is no longer blocked. + * + * If the driver buffers frames in the driver for aggregation in any + * way, it must use the ieee80211_sta_set_buffered() call when it is + * notified of the station going to sleep to inform mac80211 of any + * TIDs that have frames buffered. Note that when a station wakes up + * this information is reset (hence the requirement to call it when + * informed of the station going to sleep). Then, when a service + * period starts for any reason, @release_buffered_frames is called + * with the number of frames to be released and which TIDs they are + * to come from. In this case, the driver is responsible for setting + * the EOSP (for uAPSD) and MORE_DATA bits in the released frames, + * to help the @more_data paramter is passed to tell the driver if + * there is more data on other TIDs -- the TIDs to release frames + * from are ignored since mac80211 doesn't know how many frames the + * buffers for those TIDs contain. + * + * If the driver also implement GO mode, where absence periods may + * shorten service periods (or abort PS-Poll responses), it must + * filter those response frames except in the case of frames that + * are buffered in the driver -- those must remain buffered to avoid + * reordering. Because it is possible that no frames are released + * in this case, the driver must call ieee80211_sta_eosp() + * to indicate to mac80211 that the service period ended anyway. + * + * Finally, if frames from multiple TIDs are released from mac80211 + * but the driver might reorder them, it must clear & set the flags + * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP) + * and also take care of the EOSP and MORE_DATA bits in the frame. + * The driver may also use ieee80211_sta_eosp() in this case. + */ + +/** + * DOC: HW queue control + * + * Before HW queue control was introduced, mac80211 only had a single static + * assignment of per-interface AC software queues to hardware queues. This + * was problematic for a few reasons: + * 1) off-channel transmissions might get stuck behind other frames + * 2) multiple virtual interfaces couldn't be handled correctly + * 3) after-DTIM frames could get stuck behind other frames + * + * To solve this, hardware typically uses multiple different queues for all + * the different usages, and this needs to be propagated into mac80211 so it + * won't have the same problem with the software queues. + * + * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability + * flag that tells it that the driver implements its own queue control. To do + * so, the driver will set up the various queues in each &struct ieee80211_vif + * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will + * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and + * if necessary will queue the frame on the right software queue that mirrors + * the hardware queue. + * Additionally, the driver has to then use these HW queue IDs for the queue + * management functions (ieee80211_stop_queue() et al.) + * + * The driver is free to set up the queue mappings as needed, multiple virtual + * interfaces may map to the same hardware queues if needed. The setup has to + * happen during add_interface or change_interface callbacks. For example, a + * driver supporting station+station and station+AP modes might decide to have + * 10 hardware queues to handle different scenarios: + * + * 4 AC HW queues for 1st vif: 0, 1, 2, 3 + * 4 AC HW queues for 2nd vif: 4, 5, 6, 7 + * after-DTIM queue for AP: 8 + * off-channel queue: 9 + * + * It would then set up the hardware like this: + * hw.offchannel_tx_hw_queue = 9 + * + * and the first virtual interface that is added as follows: + * vif.hw_queue[IEEE80211_AC_VO] = 0 + * vif.hw_queue[IEEE80211_AC_VI] = 1 + * vif.hw_queue[IEEE80211_AC_BE] = 2 + * vif.hw_queue[IEEE80211_AC_BK] = 3 + * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE + * and the second virtual interface with 4-7. + * + * If queue 6 gets full, for example, mac80211 would only stop the second + * virtual interface's BE queue since virtual interface queues are per AC. + * + * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE + * whenever the queue is not used (i.e. the interface is not in AP mode) if the + * queue could potentially be shared since mac80211 will look at cab_queue when + * a queue is stopped/woken even if the interface is not in AP mode. + */ + +/** + * enum ieee80211_filter_flags - hardware filter flags + * + * These flags determine what the filter in hardware should be + * programmed to let through and what should not be passed to the + * stack. It is always safe to pass more frames than requested, + * but this has negative impact on power consumption. + * + * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS, + * think of the BSS as your network segment and then this corresponds + * to the regular ethernet device promiscuous mode. + * + * @FIF_ALLMULTI: pass all multicast frames, this is used if requested + * by the user or if the hardware is not capable of filtering by + * multicast address. + * + * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the + * %RX_FLAG_FAILED_FCS_CRC for them) + * + * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set + * the %RX_FLAG_FAILED_PLCP_CRC for them + * + * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate + * to the hardware that it should not filter beacons or probe responses + * by BSSID. Filtering them can greatly reduce the amount of processing + * mac80211 needs to do and the amount of CPU wakeups, so you should + * honour this flag if possible. + * + * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS + * is not set then only those addressed to this station. + * + * @FIF_OTHER_BSS: pass frames destined to other BSSes + * + * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only + * those addressed to this station. + * + * @FIF_PROBE_REQ: pass probe request frames + */ +enum ieee80211_filter_flags { + FIF_PROMISC_IN_BSS = 1<<0, + FIF_ALLMULTI = 1<<1, + FIF_FCSFAIL = 1<<2, + FIF_PLCPFAIL = 1<<3, + FIF_BCN_PRBRESP_PROMISC = 1<<4, + FIF_CONTROL = 1<<5, + FIF_OTHER_BSS = 1<<6, + FIF_PSPOLL = 1<<7, + FIF_PROBE_REQ = 1<<8, +}; + +/** + * enum ieee80211_ampdu_mlme_action - A-MPDU actions + * + * These flags are used with the ampdu_action() callback in + * &struct ieee80211_ops to indicate which action is needed. + * + * Note that drivers MUST be able to deal with a TX aggregation + * session being stopped even before they OK'ed starting it by + * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer + * might receive the addBA frame and send a delBA right away! + * + * @IEEE80211_AMPDU_RX_START: start RX aggregation + * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation + * @IEEE80211_AMPDU_TX_START: start TX aggregation + * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational + * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting + * queued packets, now unaggregated. After all packets are transmitted the + * driver has to call ieee80211_stop_tx_ba_cb_irqsafe(). + * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets, + * called when the station is removed. There's no need or reason to call + * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the + * session is gone and removes the station. + * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped + * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and + * now the connection is dropped and the station will be removed. Drivers + * should clean up and drop remaining packets when this is called. + */ +enum ieee80211_ampdu_mlme_action { + IEEE80211_AMPDU_RX_START, + IEEE80211_AMPDU_RX_STOP, + IEEE80211_AMPDU_TX_START, + IEEE80211_AMPDU_TX_STOP_CONT, + IEEE80211_AMPDU_TX_STOP_FLUSH, + IEEE80211_AMPDU_TX_STOP_FLUSH_CONT, + IEEE80211_AMPDU_TX_OPERATIONAL, +}; + +/** + * enum ieee80211_frame_release_type - frame release reason + * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll + * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to + * frame received on trigger-enabled AC + */ +enum ieee80211_frame_release_type { + IEEE80211_FRAME_RELEASE_PSPOLL, + IEEE80211_FRAME_RELEASE_UAPSD, +}; + +/** + * enum ieee80211_rate_control_changed - flags to indicate what changed + * + * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit + * to this station changed. The actual bandwidth is in the station + * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40 + * flag changes, for HT and VHT the bandwidth field changes. + * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed. + * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer + * changed (in IBSS mode) due to discovering more information about + * the peer. + * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed + * by the peer + */ +enum ieee80211_rate_control_changed { + IEEE80211_RC_BW_CHANGED = BIT(0), + IEEE80211_RC_SMPS_CHANGED = BIT(1), + IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2), + IEEE80211_RC_NSS_CHANGED = BIT(3), +}; + +/** + * enum ieee80211_roc_type - remain on channel type + * + * With the support for multi channel contexts and multi channel operations, + * remain on channel operations might be limited/deferred/aborted by other + * flows/operations which have higher priority (and vise versa). + * Specifying the ROC type can be used by devices to prioritize the ROC + * operations compared to other operations/flows. + * + * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC. + * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required + * for sending managment frames offchannel. + */ +enum ieee80211_roc_type { + IEEE80211_ROC_TYPE_NORMAL = 0, + IEEE80211_ROC_TYPE_MGMT_TX, +}; + +/** + * struct ieee80211_ops - callbacks from mac80211 to the driver + * + * This structure contains various callbacks that the driver may + * handle or, in some cases, must handle, for example to configure + * the hardware to a new channel or to transmit a frame. + * + * @tx: Handler that 802.11 module calls for each transmitted frame. + * skb contains the buffer starting from the IEEE 802.11 header. + * The low-level driver should send the frame out based on + * configuration in the TX control data. This handler should, + * preferably, never fail and stop queues appropriately. + * Must be atomic. + * + * @start: Called before the first netdevice attached to the hardware + * is enabled. This should turn on the hardware and must turn on + * frame reception (for possibly enabled monitor interfaces.) + * Returns negative error codes, these may be seen in userspace, + * or zero. + * When the device is started it should not have a MAC address + * to avoid acknowledging frames before a non-monitor device + * is added. + * Must be implemented and can sleep. + * + * @stop: Called after last netdevice attached to the hardware + * is disabled. This should turn off the hardware (at least + * it must turn off frame reception.) + * May be called right after add_interface if that rejects + * an interface. If you added any work onto the mac80211 workqueue + * you should ensure to cancel it on this callback. + * Must be implemented and can sleep. + * + * @suspend: Suspend the device; mac80211 itself will quiesce before and + * stop transmitting and doing any other configuration, and then + * ask the device to suspend. This is only invoked when WoWLAN is + * configured, otherwise the device is deconfigured completely and + * reconfigured at resume time. + * The driver may also impose special conditions under which it + * wants to use the "normal" suspend (deconfigure), say if it only + * supports WoWLAN when the device is associated. In this case, it + * must return 1 from this function. + * + * @resume: If WoWLAN was configured, this indicates that mac80211 is + * now resuming its operation, after this the device must be fully + * functional again. If this returns an error, the only way out is + * to also unregister the device. If it returns 1, then mac80211 + * will also go through the regular complete restart on resume. + * + * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is + * modified. The reason is that device_set_wakeup_enable() is + * supposed to be called when the configuration changes, not only + * in suspend(). + * + * @add_interface: Called when a netdevice attached to the hardware is + * enabled. Because it is not called for monitor mode devices, @start + * and @stop must be implemented. + * The driver should perform any initialization it needs before + * the device can be enabled. The initial configuration for the + * interface is given in the conf parameter. + * The callback may refuse to add an interface by returning a + * negative error code (which will be seen in userspace.) + * Must be implemented and can sleep. + * + * @change_interface: Called when a netdevice changes type. This callback + * is optional, but only if it is supported can interface types be + * switched while the interface is UP. The callback may sleep. + * Note that while an interface is being switched, it will not be + * found by the interface iteration callbacks. + * + * @remove_interface: Notifies a driver that an interface is going down. + * The @stop callback is called after this if it is the last interface + * and no monitor interfaces are present. + * When all interfaces are removed, the MAC address in the hardware + * must be cleared so the device no longer acknowledges packets, + * the mac_addr member of the conf structure is, however, set to the + * MAC address of the device going away. + * Hence, this callback must be implemented. It can sleep. + * + * @config: Handler for configuration requests. IEEE 802.11 code calls this + * function to change hardware configuration, e.g., channel. + * This function should never fail but returns a negative error code + * if it does. The callback can sleep. + * + * @bss_info_changed: Handler for configuration requests related to BSS + * parameters that may vary during BSS's lifespan, and may affect low + * level driver (e.g. assoc/disassoc status, erp parameters). + * This function should not be used if no BSS has been set, unless + * for association indication. The @changed parameter indicates which + * of the bss parameters has changed when a call is made. The callback + * can sleep. + * + * @prepare_multicast: Prepare for multicast filter configuration. + * This callback is optional, and its return value is passed + * to configure_filter(). This callback must be atomic. + * + * @configure_filter: Configure the device's RX filter. + * See the section "Frame filtering" for more information. + * This callback must be implemented and can sleep. + * + * @set_multicast_list: Configure the device's interface specific RX multicast + * filter. This callback is optional. This callback must be atomic. + * + * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit + * must be set or cleared for a given STA. Must be atomic. + * + * @set_key: See the section "Hardware crypto acceleration" + * This callback is only called between add_interface and + * remove_interface calls, i.e. while the given virtual interface + * is enabled. + * Returns a negative error code if the key can't be added. + * The callback can sleep. + * + * @update_tkip_key: See the section "Hardware crypto acceleration" + * This callback will be called in the context of Rx. Called for drivers + * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. + * The callback must be atomic. + * + * @set_rekey_data: If the device supports GTK rekeying, for example while the + * host is suspended, it can assign this callback to retrieve the data + * necessary to do GTK rekeying, this is the KEK, KCK and replay counter. + * After rekeying was done it should (for example during resume) notify + * userspace of the new replay counter using ieee80211_gtk_rekey_notify(). + * + * @set_default_unicast_key: Set the default (unicast) key index, useful for + * WEP when the device sends data packets autonomously, e.g. for ARP + * offloading. The index can be 0-3, or -1 for unsetting it. + * + * @hw_scan: Ask the hardware to service the scan request, no need to start + * the scan state machine in stack. The scan must honour the channel + * configuration done by the regulatory agent in the wiphy's + * registered bands. The hardware (or the driver) needs to make sure + * that power save is disabled. + * The @req ie/ie_len members are rewritten by mac80211 to contain the + * entire IEs after the SSID, so that drivers need not look at these + * at all but just send them after the SSID -- mac80211 includes the + * (extended) supported rates and HT information (where applicable). + * When the scan finishes, ieee80211_scan_completed() must be called; + * note that it also must be called when the scan cannot finish due to + * any error unless this callback returned a negative error code. + * The callback can sleep. + * + * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan. + * The driver should ask the hardware to cancel the scan (if possible), + * but the scan will be completed only after the driver will call + * ieee80211_scan_completed(). + * This callback is needed for wowlan, to prevent enqueueing a new + * scan_work after the low-level driver was already suspended. + * The callback can sleep. + * + * @sched_scan_start: Ask the hardware to start scanning repeatedly at + * specific intervals. The driver must call the + * ieee80211_sched_scan_results() function whenever it finds results. + * This process will continue until sched_scan_stop is called. + * + * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan. + * + * @sw_scan_start: Notifier function that is called just before a software scan + * is started. Can be NULL, if the driver doesn't need this notification. + * The callback can sleep. + * + * @sw_scan_complete: Notifier function that is called just after a + * software scan finished. Can be NULL, if the driver doesn't need + * this notification. + * The callback can sleep. + * + * @get_stats: Return low-level statistics. + * Returns zero if statistics are available. + * The callback can sleep. + * + * @get_tkip_seq: If your device implements TKIP encryption in hardware this + * callback should be provided to read the TKIP transmit IVs (both IV32 + * and IV16) for the given key from hardware. + * The callback must be atomic. + * + * @set_frag_threshold: Configuration of fragmentation threshold. Assign this + * if the device does fragmentation by itself; if this callback is + * implemented then the stack will not do fragmentation. + * The callback can sleep. + * + * @set_rts_threshold: Configuration of RTS threshold (if device needs it) + * The callback can sleep. + * + * @sta_add: Notifies low level driver about addition of an associated station, + * AP, IBSS/WDS/mesh peer etc. This callback can sleep. + * + * @sta_remove: Notifies low level driver about removal of an associated + * station, AP, IBSS/WDS/mesh peer etc. This callback can sleep. + * + * @sta_add_debugfs: Drivers can use this callback to add debugfs files + * when a station is added to mac80211's station list. This callback + * and @sta_remove_debugfs should be within a CPTCFG_MAC80211_DEBUGFS + * conditional. This callback can sleep. + * + * @sta_remove_debugfs: Remove the debugfs files which were added using + * @sta_add_debugfs. This callback can sleep. + * + * @sta_notify: Notifies low level driver about power state transition of an + * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating + * in AP mode, this callback will not be called when the flag + * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic. + * + * @sta_state: Notifies low level driver about state transition of a + * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.) + * This callback is mutually exclusive with @sta_add/@sta_remove. + * It must not fail for down transitions but may fail for transitions + * up the list of states. + * The callback can sleep. + * + * @sta_rc_update: Notifies the driver of changes to the bitrates that can be + * used to transmit to the station. The changes are advertised with bits + * from &enum ieee80211_rate_control_changed and the values are reflected + * in the station data. This callback should only be used when the driver + * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since + * otherwise the rate control algorithm is notified directly. + * Must be atomic. + * + * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), + * bursting) for a hardware TX queue. + * Returns a negative error code on failure. + * The callback can sleep. + * + * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, + * this is only used for IBSS mode BSSID merging and debugging. Is not a + * required function. + * The callback can sleep. + * + * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. + * Currently, this is only used for IBSS mode debugging. Is not a + * required function. + * The callback can sleep. + * + * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize + * with other STAs in the IBSS. This is only used in IBSS mode. This + * function is optional if the firmware/hardware takes full care of + * TSF synchronization. + * The callback can sleep. + * + * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. + * This is needed only for IBSS mode and the result of this function is + * used to determine whether to reply to Probe Requests. + * Returns non-zero if this device sent the last beacon. + * The callback can sleep. + * + * @ampdu_action: Perform a certain A-MPDU action + * The RA/TID combination determines the destination and TID we want + * the ampdu action to be performed for. The action is defined through + * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) + * is the first frame we expect to perform the action on. Notice + * that TX/RX_STOP can pass NULL for this parameter. + * The @buf_size parameter is only valid when the action is set to + * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder + * buffer size (number of subframes) for this session -- the driver + * may neither send aggregates containing more subframes than this + * nor send aggregates in a way that lost frames would exceed the + * buffer size. If just limiting the aggregate size, this would be + * possible with a buf_size of 8: + * - TX: 1.....7 + * - RX: 2....7 (lost frame #1) + * - TX: 8..1... + * which is invalid since #1 was now re-transmitted well past the + * buffer size of 8. Correct ways to retransmit #1 would be: + * - TX: 1 or 18 or 81 + * Even "189" would be wrong since 1 could be lost again. + * + * Returns a negative error code on failure. + * The callback can sleep. + * + * @get_survey: Return per-channel survey information + * + * @rfkill_poll: Poll rfkill hardware state. If you need this, you also + * need to set wiphy->rfkill_poll to %true before registration, + * and need to call wiphy_rfkill_set_hw_state() in the callback. + * The callback can sleep. + * + * @set_coverage_class: Set slot time for given coverage class as specified + * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout + * accordingly. This callback is not required and may sleep. + * + * @testmode_cmd: Implement a cfg80211 test mode command. + * The callback can sleep. + * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep. + * + * @flush: Flush all pending frames from the hardware queue, making sure + * that the hardware queues are empty. The @queues parameter is a bitmap + * of queues to flush, which is useful if different virtual interfaces + * use different hardware queues; it may also indicate all queues. + * If the parameter @drop is set to %true, pending frames may be dropped. + * The callback can sleep. + * + * @channel_switch: Drivers that need (or want) to offload the channel + * switch operation for CSAs received from the AP may implement this + * callback. They must then call ieee80211_chswitch_done() to indicate + * completion of the channel switch. + * + * @napi_poll: Poll Rx queue for incoming data frames. + * + * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. + * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may + * reject TX/RX mask combinations they cannot support by returning -EINVAL + * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX). + * + * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant). + * + * @remain_on_channel: Starts an off-channel period on the given channel, must + * call back to ieee80211_ready_on_channel() when on that channel. Note + * that normal channel traffic is not stopped as this is intended for hw + * offload. Frames to transmit on the off-channel channel are transmitted + * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the + * duration (which will always be non-zero) expires, the driver must call + * ieee80211_remain_on_channel_expired(). + * Note that this callback may be called while the device is in IDLE and + * must be accepted in this case. + * This callback may sleep. + * @cancel_remain_on_channel: Requests that an ongoing off-channel period is + * aborted before it expires. This callback may sleep. + * + * @set_ringparam: Set tx and rx ring sizes. + * + * @get_ringparam: Get tx and rx ring current and maximum sizes. + * + * @tx_frames_pending: Check if there is any pending frame in the hardware + * queues before entering power save. + * + * @set_bitrate_mask: Set a mask of rates to be used for rate control selection + * when transmitting a frame. Currently only legacy rates are handled. + * The callback can sleep. + * @rssi_callback: Notify driver when the average RSSI goes above/below + * thresholds that were registered previously. The callback can sleep. + * + * @release_buffered_frames: Release buffered frames according to the given + * parameters. In the case where the driver buffers some frames for + * sleeping stations mac80211 will use this callback to tell the driver + * to release some frames, either for PS-poll or uAPSD. + * Note that if the @more_data paramter is %false the driver must check + * if there are more frames on the given TIDs, and if there are more than + * the frames being released then it must still set the more-data bit in + * the frame. If the @more_data parameter is %true, then of course the + * more-data bit must always be set. + * The @tids parameter tells the driver which TIDs to release frames + * from, for PS-poll it will always have only a single bit set. + * In the case this is used for a PS-poll initiated release, the + * @num_frames parameter will always be 1 so code can be shared. In + * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag + * on the TX status (and must report TX status) so that the PS-poll + * period is properly ended. This is used to avoid sending multiple + * responses for a retried PS-poll frame. + * In the case this is used for uAPSD, the @num_frames parameter may be + * bigger than one, but the driver may send fewer frames (it must send + * at least one, however). In this case it is also responsible for + * setting the EOSP flag in the QoS header of the frames. Also, when the + * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP + * on the last frame in the SP. Alternatively, it may call the function + * ieee80211_sta_eosp() to inform mac80211 of the end of the SP. + * This callback must be atomic. + * @allow_buffered_frames: Prepare device to allow the given number of frames + * to go out to the given station. The frames will be sent by mac80211 + * via the usual TX path after this call. The TX information for frames + * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set + * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case + * frames from multiple TIDs are released and the driver might reorder + * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag + * on the last frame and clear it on all others and also handle the EOSP + * bit in the QoS header correctly. Alternatively, it can also call the + * ieee80211_sta_eosp() function. + * The @tids parameter is a bitmap and tells the driver which TIDs the + * frames will be on; it will at most have two bits set. + * This callback must be atomic. + * + * @get_et_sset_count: Ethtool API to get string-set count. + * + * @get_et_stats: Ethtool API to get a set of u64 stats. + * + * @get_et_strings: Ethtool API to get a set of strings to describe stats + * and perhaps other supported types of ethtool data-sets. + * + * @get_rssi: Get current signal strength in dBm, the function is optional + * and can sleep. + * + * @mgd_prepare_tx: Prepare for transmitting a management frame for association + * before associated. In multi-channel scenarios, a virtual interface is + * bound to a channel before it is associated, but as it isn't associated + * yet it need not necessarily be given airtime, in particular since any + * transmission to a P2P GO needs to be synchronized against the GO's + * powersave state. mac80211 will call this function before transmitting a + * management frame prior to having successfully associated to allow the + * driver to give it channel time for the transmission, to get a response + * and to be able to synchronize with the GO. + * The callback will be called before each transmission and upon return + * mac80211 will transmit the frame right away. + * The callback is optional and can (should!) sleep. + * + * @add_chanctx: Notifies device driver about new channel context creation. + * @remove_chanctx: Notifies device driver about channel context destruction. + * @change_chanctx: Notifies device driver about channel context changes that + * may happen when combining different virtual interfaces on the same + * channel context with different settings + * @assign_vif_chanctx: Notifies device driver about channel context being bound + * to vif. Possible use is for hw queue remapping. + * @unassign_vif_chanctx: Notifies device driver about channel context being + * unbound from vif. + * @start_ap: Start operation on the AP interface, this is called after all the + * information in bss_conf is set and beacon can be retrieved. A channel + * context is bound before this is called. Note that if the driver uses + * software scan or ROC, this (and @stop_ap) isn't called when the AP is + * just "paused" for scanning/ROC, which is indicated by the beacon being + * disabled/enabled via @bss_info_changed. + * @stop_ap: Stop operation on the AP interface. + * + * @restart_complete: Called after a call to ieee80211_restart_hw(), when the + * reconfiguration has completed. This can help the driver implement the + * reconfiguration step. Also called when reconfiguring because the + * driver's resume function returned 1, as this is just like an "inline" + * hardware restart. This callback may sleep. + * + * @ipv6_addr_change: IPv6 address assignment on the given interface changed. + * Currently, this is only called for managed or P2P client interfaces. + * This callback is optional; it must not sleep. + */ +struct ieee80211_ops { + void (*tx)(struct ieee80211_hw *hw, + struct ieee80211_tx_control *control, + struct sk_buff *skb); + int (*start)(struct ieee80211_hw *hw); + void (*stop)(struct ieee80211_hw *hw); +#ifdef CONFIG_PM + int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan); + int (*resume)(struct ieee80211_hw *hw); + void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled); +#endif + int (*add_interface)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + int (*change_interface)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum nl80211_iftype new_type, bool p2p); + void (*remove_interface)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + int (*config)(struct ieee80211_hw *hw, u32 changed); + void (*bss_info_changed)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_bss_conf *info, + u32 changed); + + int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + + u64 (*prepare_multicast)(struct ieee80211_hw *hw, +#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,35)) + struct netdev_hw_addr_list *mc_list); +#else + int mc_count, struct dev_addr_list *mc_list); +#endif + void (*configure_filter)(struct ieee80211_hw *hw, + unsigned int changed_flags, + unsigned int *total_flags, + u64 multicast); +#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,35)) + void (*set_multicast_list)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, bool allmulti, + struct netdev_hw_addr_list *mc_list); +#else + void (*set_multicast_list)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, bool allmulti, + int mc_count, struct dev_addr_list *ha); +#endif + + int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, + bool set); + int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, + struct ieee80211_vif *vif, struct ieee80211_sta *sta, + struct ieee80211_key_conf *key); + void (*update_tkip_key)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_key_conf *conf, + struct ieee80211_sta *sta, + u32 iv32, u16 *phase1key); + void (*set_rekey_data)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_gtk_rekey_data *data); + void (*set_default_unicast_key)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, int idx); + int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct cfg80211_scan_request *req); + void (*cancel_hw_scan)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + int (*sched_scan_start)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_sched_scan_request *req, + struct ieee80211_sched_scan_ies *ies); + void (*sched_scan_stop)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + void (*sw_scan_start)(struct ieee80211_hw *hw); + void (*sw_scan_complete)(struct ieee80211_hw *hw); + int (*get_stats)(struct ieee80211_hw *hw, + struct ieee80211_low_level_stats *stats); + void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, + u32 *iv32, u16 *iv16); + int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); + int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); + int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta); + int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta); +#ifdef CPTCFG_MAC80211_DEBUGFS + void (*sta_add_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct dentry *dir); + void (*sta_remove_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct dentry *dir); +#endif + void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + enum sta_notify_cmd, struct ieee80211_sta *sta); + int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + enum ieee80211_sta_state old_state, + enum ieee80211_sta_state new_state); + void (*sta_rc_update)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + u32 changed); + int (*conf_tx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, u16 ac, + const struct ieee80211_tx_queue_params *params); + u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + u64 tsf); + void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + int (*tx_last_beacon)(struct ieee80211_hw *hw); + int (*ampdu_action)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum ieee80211_ampdu_mlme_action action, + struct ieee80211_sta *sta, u16 tid, u16 *ssn, + u8 buf_size); + int (*get_survey)(struct ieee80211_hw *hw, int idx, + struct survey_info *survey); + void (*rfkill_poll)(struct ieee80211_hw *hw); + void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class); +#ifdef CPTCFG_NL80211_TESTMODE + int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len); + int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb, + struct netlink_callback *cb, + void *data, int len); +#endif + void (*flush)(struct ieee80211_hw *hw, u32 queues, bool drop); + void (*channel_switch)(struct ieee80211_hw *hw, + struct ieee80211_channel_switch *ch_switch); + int (*napi_poll)(struct ieee80211_hw *hw, int budget); + int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); + int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); + + int (*remain_on_channel)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_channel *chan, + int duration, + enum ieee80211_roc_type type); + int (*cancel_remain_on_channel)(struct ieee80211_hw *hw); + int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx); + void (*get_ringparam)(struct ieee80211_hw *hw, + u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max); + bool (*tx_frames_pending)(struct ieee80211_hw *hw); + int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + const struct cfg80211_bitrate_mask *mask); + void (*rssi_callback)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum ieee80211_rssi_event rssi_event); + + void (*allow_buffered_frames)(struct ieee80211_hw *hw, + struct ieee80211_sta *sta, + u16 tids, int num_frames, + enum ieee80211_frame_release_type reason, + bool more_data); + void (*release_buffered_frames)(struct ieee80211_hw *hw, + struct ieee80211_sta *sta, + u16 tids, int num_frames, + enum ieee80211_frame_release_type reason, + bool more_data); + + int (*get_et_sset_count)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, int sset); + void (*get_et_stats)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ethtool_stats *stats, u64 *data); + void (*get_et_strings)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + u32 sset, u8 *data); + int (*get_rssi)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta, s8 *rssi_dbm); + + void (*mgd_prepare_tx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + + int (*add_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx); + void (*remove_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx); + void (*change_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx, + u32 changed); + int (*assign_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_chanctx_conf *ctx); + void (*unassign_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_chanctx_conf *ctx); + + void (*restart_complete)(struct ieee80211_hw *hw); + +#if IS_ENABLED(CONFIG_IPV6) + void (*ipv6_addr_change)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct inet6_dev *idev); +#endif +}; + +/** + * ieee80211_alloc_hw - Allocate a new hardware device + * + * This must be called once for each hardware device. The returned pointer + * must be used to refer to this device when calling other functions. + * mac80211 allocates a private data area for the driver pointed to by + * @priv in &struct ieee80211_hw, the size of this area is given as + * @priv_data_len. + * + * @priv_data_len: length of private data + * @ops: callbacks for this device + * + * Return: A pointer to the new hardware device, or %NULL on error. + */ +struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, + const struct ieee80211_ops *ops); + +/** + * ieee80211_register_hw - Register hardware device + * + * You must call this function before any other functions in + * mac80211. Note that before a hardware can be registered, you + * need to fill the contained wiphy's information. + * + * @hw: the device to register as returned by ieee80211_alloc_hw() + * + * Return: 0 on success. An error code otherwise. + */ +int ieee80211_register_hw(struct ieee80211_hw *hw); + +/** + * struct ieee80211_tpt_blink - throughput blink description + * @throughput: throughput in Kbit/sec + * @blink_time: blink time in milliseconds + * (full cycle, ie. one off + one on period) + */ +struct ieee80211_tpt_blink { + int throughput; + int blink_time; +}; + +/** + * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags + * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio + * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working + * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one + * interface is connected in some way, including being an AP + */ +enum ieee80211_tpt_led_trigger_flags { + IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0), + IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1), + IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2), +}; + +#ifdef CPTCFG_MAC80211_LEDS +extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); +extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); +extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); +extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); +extern char *__ieee80211_create_tpt_led_trigger( + struct ieee80211_hw *hw, unsigned int flags, + const struct ieee80211_tpt_blink *blink_table, + unsigned int blink_table_len); +#endif +/** + * ieee80211_get_tx_led_name - get name of TX LED + * + * mac80211 creates a transmit LED trigger for each wireless hardware + * that can be used to drive LEDs if your driver registers a LED device. + * This function returns the name (or %NULL if not configured for LEDs) + * of the trigger so you can automatically link the LED device. + * + * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. + */ +static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) +{ +#ifdef CPTCFG_MAC80211_LEDS + return __ieee80211_get_tx_led_name(hw); +#else + return NULL; +#endif +} + +/** + * ieee80211_get_rx_led_name - get name of RX LED + * + * mac80211 creates a receive LED trigger for each wireless hardware + * that can be used to drive LEDs if your driver registers a LED device. + * This function returns the name (or %NULL if not configured for LEDs) + * of the trigger so you can automatically link the LED device. + * + * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. + */ +static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) +{ +#ifdef CPTCFG_MAC80211_LEDS + return __ieee80211_get_rx_led_name(hw); +#else + return NULL; +#endif +} + +/** + * ieee80211_get_assoc_led_name - get name of association LED + * + * mac80211 creates a association LED trigger for each wireless hardware + * that can be used to drive LEDs if your driver registers a LED device. + * This function returns the name (or %NULL if not configured for LEDs) + * of the trigger so you can automatically link the LED device. + * + * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. + */ +static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) +{ +#ifdef CPTCFG_MAC80211_LEDS + return __ieee80211_get_assoc_led_name(hw); +#else + return NULL; +#endif +} + +/** + * ieee80211_get_radio_led_name - get name of radio LED + * + * mac80211 creates a radio change LED trigger for each wireless hardware + * that can be used to drive LEDs if your driver registers a LED device. + * This function returns the name (or %NULL if not configured for LEDs) + * of the trigger so you can automatically link the LED device. + * + * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. + */ +static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) +{ +#ifdef CPTCFG_MAC80211_LEDS + return __ieee80211_get_radio_led_name(hw); +#else + return NULL; +#endif +} + +/** + * ieee80211_create_tpt_led_trigger - create throughput LED trigger + * @hw: the hardware to create the trigger for + * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags + * @blink_table: the blink table -- needs to be ordered by throughput + * @blink_table_len: size of the blink table + * + * Return: %NULL (in case of error, or if no LED triggers are + * configured) or the name of the new trigger. + * + * Note: This function must be called before ieee80211_register_hw(). + */ +static inline char * +ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, + const struct ieee80211_tpt_blink *blink_table, + unsigned int blink_table_len) +{ +#ifdef CPTCFG_MAC80211_LEDS + return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table, + blink_table_len); +#else + return NULL; +#endif +} + +/** + * ieee80211_unregister_hw - Unregister a hardware device + * + * This function instructs mac80211 to free allocated resources + * and unregister netdevices from the networking subsystem. + * + * @hw: the hardware to unregister + */ +void ieee80211_unregister_hw(struct ieee80211_hw *hw); + +/** + * ieee80211_free_hw - free hardware descriptor + * + * This function frees everything that was allocated, including the + * private data for the driver. You must call ieee80211_unregister_hw() + * before calling this function. + * + * @hw: the hardware to free + */ +void ieee80211_free_hw(struct ieee80211_hw *hw); + +/** + * ieee80211_restart_hw - restart hardware completely + * + * Call this function when the hardware was restarted for some reason + * (hardware error, ...) and the driver is unable to restore its state + * by itself. mac80211 assumes that at this point the driver/hardware + * is completely uninitialised and stopped, it starts the process by + * calling the ->start() operation. The driver will need to reset all + * internal state that it has prior to calling this function. + * + * @hw: the hardware to restart + */ +void ieee80211_restart_hw(struct ieee80211_hw *hw); + +/** ieee80211_napi_schedule - schedule NAPI poll + * + * Use this function to schedule NAPI polling on a device. + * + * @hw: the hardware to start polling + */ +void ieee80211_napi_schedule(struct ieee80211_hw *hw); + +/** ieee80211_napi_complete - complete NAPI polling + * + * Use this function to finish NAPI polling on a device. + * + * @hw: the hardware to stop polling + */ +void ieee80211_napi_complete(struct ieee80211_hw *hw); + +/** + * ieee80211_rx - receive frame + * + * Use this function to hand received frames to mac80211. The receive + * buffer in @skb must start with an IEEE 802.11 header. In case of a + * paged @skb is used, the driver is recommended to put the ieee80211 + * header of the frame on the linear part of the @skb to avoid memory + * allocation and/or memcpy by the stack. + * + * This function may not be called in IRQ context. Calls to this function + * for a single hardware must be synchronized against each other. Calls to + * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be + * mixed for a single hardware. Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). + * + * In process context use instead ieee80211_rx_ni(). + * + * @hw: the hardware this frame came in on + * @skb: the buffer to receive, owned by mac80211 after this call + */ +void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb); + +/** + * ieee80211_rx_irqsafe - receive frame + * + * Like ieee80211_rx() but can be called in IRQ context + * (internally defers to a tasklet.) + * + * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not + * be mixed for a single hardware.Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). + * + * @hw: the hardware this frame came in on + * @skb: the buffer to receive, owned by mac80211 after this call + */ +void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb); + +/** + * ieee80211_rx_ni - receive frame (in process context) + * + * Like ieee80211_rx() but can be called in process context + * (internally disables bottom halves). + * + * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may + * not be mixed for a single hardware. Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). + * + * @hw: the hardware this frame came in on + * @skb: the buffer to receive, owned by mac80211 after this call + */ +static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, + struct sk_buff *skb) +{ + local_bh_disable(); + ieee80211_rx(hw, skb); + local_bh_enable(); +} + +/** + * ieee80211_sta_ps_transition - PS transition for connected sta + * + * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS + * flag set, use this function to inform mac80211 about a connected station + * entering/leaving PS mode. + * + * This function may not be called in IRQ context or with softirqs enabled. + * + * Calls to this function for a single hardware must be synchronized against + * each other. + * + * @sta: currently connected sta + * @start: start or stop PS + * + * Return: 0 on success. -EINVAL when the requested PS mode is already set. + */ +int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); + +/** + * ieee80211_sta_ps_transition_ni - PS transition for connected sta + * (in process context) + * + * Like ieee80211_sta_ps_transition() but can be called in process context + * (internally disables bottom halves). Concurrent call restriction still + * applies. + * + * @sta: currently connected sta + * @start: start or stop PS + * + * Return: Like ieee80211_sta_ps_transition(). + */ +static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta, + bool start) +{ + int ret; + + local_bh_disable(); + ret = ieee80211_sta_ps_transition(sta, start); + local_bh_enable(); + + return ret; +} + +/* + * The TX headroom reserved by mac80211 for its own tx_status functions. + * This is enough for the radiotap header. + */ +#define IEEE80211_TX_STATUS_HEADROOM 14 + +/** + * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames + * @sta: &struct ieee80211_sta pointer for the sleeping station + * @tid: the TID that has buffered frames + * @buffered: indicates whether or not frames are buffered for this TID + * + * If a driver buffers frames for a powersave station instead of passing + * them back to mac80211 for retransmission, the station may still need + * to be told that there are buffered frames via the TIM bit. + * + * This function informs mac80211 whether or not there are frames that are + * buffered in the driver for a given TID; mac80211 can then use this data + * to set the TIM bit (NOTE: This may call back into the driver's set_tim + * call! Beware of the locking!) + * + * If all frames are released to the station (due to PS-poll or uAPSD) + * then the driver needs to inform mac80211 that there no longer are + * frames buffered. However, when the station wakes up mac80211 assumes + * that all buffered frames will be transmitted and clears this data, + * drivers need to make sure they inform mac80211 about all buffered + * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP). + * + * Note that technically mac80211 only needs to know this per AC, not per + * TID, but since driver buffering will inevitably happen per TID (since + * it is related to aggregation) it is easier to make mac80211 map the + * TID to the AC as required instead of keeping track in all drivers that + * use this API. + */ +void ieee80211_sta_set_buffered(struct ieee80211_sta *sta, + u8 tid, bool buffered); + +/** + * ieee80211_get_tx_rates - get the selected transmit rates for a packet + * + * Call this function in a driver with per-packet rate selection support + * to combine the rate info in the packet tx info with the most recent + * rate selection table for the station entry. + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @sta: the receiver station to which this packet is sent. + * @skb: the frame to be transmitted. + * @dest: buffer for extracted rate/retry information + * @max_rates: maximum number of rates to fetch + */ +void ieee80211_get_tx_rates(struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct sk_buff *skb, + struct ieee80211_tx_rate *dest, + int max_rates); + +/** + * ieee80211_tx_status - transmit status callback + * + * Call this function for all transmitted frames after they have been + * transmitted. It is permissible to not call this function for + * multicast frames but this can affect statistics. + * + * This function may not be called in IRQ context. Calls to this function + * for a single hardware must be synchronized against each other. Calls + * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe() + * may not be mixed for a single hardware. Must not run concurrently with + * ieee80211_rx() or ieee80211_rx_ni(). + * + * @hw: the hardware the frame was transmitted by + * @skb: the frame that was transmitted, owned by mac80211 after this call + */ +void ieee80211_tx_status(struct ieee80211_hw *hw, + struct sk_buff *skb); + +/** + * ieee80211_tx_status_ni - transmit status callback (in process context) + * + * Like ieee80211_tx_status() but can be called in process context. + * + * Calls to this function, ieee80211_tx_status() and + * ieee80211_tx_status_irqsafe() may not be mixed + * for a single hardware. + * + * @hw: the hardware the frame was transmitted by + * @skb: the frame that was transmitted, owned by mac80211 after this call + */ +static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw, + struct sk_buff *skb) +{ + local_bh_disable(); + ieee80211_tx_status(hw, skb); + local_bh_enable(); +} + +/** + * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback + * + * Like ieee80211_tx_status() but can be called in IRQ context + * (internally defers to a tasklet.) + * + * Calls to this function, ieee80211_tx_status() and + * ieee80211_tx_status_ni() may not be mixed for a single hardware. + * + * @hw: the hardware the frame was transmitted by + * @skb: the frame that was transmitted, owned by mac80211 after this call + */ +void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, + struct sk_buff *skb); + +/** + * ieee80211_report_low_ack - report non-responding station + * + * When operating in AP-mode, call this function to report a non-responding + * connected STA. + * + * @sta: the non-responding connected sta + * @num_packets: number of packets sent to @sta without a response + */ +void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); + +/** + * ieee80211_beacon_get_tim - beacon generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @tim_offset: pointer to variable that will receive the TIM IE offset. + * Set to 0 if invalid (in non-AP modes). + * @tim_length: pointer to variable that will receive the TIM IE length, + * (including the ID and length bytes!). + * Set to 0 if invalid (in non-AP modes). + * + * If the driver implements beaconing modes, it must use this function to + * obtain the beacon frame/template. + * + * If the beacon frames are generated by the host system (i.e., not in + * hardware/firmware), the driver uses this function to get each beacon + * frame from mac80211 -- it is responsible for calling this function + * before the beacon is needed (e.g. based on hardware interrupt). + * + * If the beacon frames are generated by the device, then the driver + * must use the returned beacon as the template and change the TIM IE + * according to the current DTIM parameters/TIM bitmap. + * + * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. + */ +struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + u16 *tim_offset, u16 *tim_length); + +/** + * ieee80211_beacon_get - beacon generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * See ieee80211_beacon_get_tim(). + * + * Return: See ieee80211_beacon_get_tim(). + */ +static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif) +{ + return ieee80211_beacon_get_tim(hw, vif, NULL, NULL); +} + +/** + * ieee80211_proberesp_get - retrieve a Probe Response template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Creates a Probe Response template which can, for example, be uploaded to + * hardware. The destination address should be set by the caller. + * + * Can only be called in AP mode. + * + * Return: The Probe Response template. %NULL on error. + */ +struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** + * ieee80211_pspoll_get - retrieve a PS Poll template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Creates a PS Poll a template which can, for example, uploaded to + * hardware. The template must be updated after association so that correct + * AID, BSSID and MAC address is used. + * + * Note: Caller (or hardware) is responsible for setting the + * &IEEE80211_FCTL_PM bit. + * + * Return: The PS Poll template. %NULL on error. + */ +struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** + * ieee80211_nullfunc_get - retrieve a nullfunc template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Creates a Nullfunc template which can, for example, uploaded to + * hardware. The template must be updated after association so that correct + * BSSID and address is used. + * + * Note: Caller (or hardware) is responsible for setting the + * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields. + * + * Return: The nullfunc template. %NULL on error. + */ +struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** + * ieee80211_probereq_get - retrieve a Probe Request template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ssid: SSID buffer + * @ssid_len: length of SSID + * @tailroom: tailroom to reserve at end of SKB for IEs + * + * Creates a Probe Request template which can, for example, be uploaded to + * hardware. + * + * Return: The Probe Request template. %NULL on error. + */ +struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + const u8 *ssid, size_t ssid_len, + size_t tailroom); + +/** + * ieee80211_rts_get - RTS frame generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @frame: pointer to the frame that is going to be protected by the RTS. + * @frame_len: the frame length (in octets). + * @frame_txctl: &struct ieee80211_tx_info of the frame. + * @rts: The buffer where to store the RTS frame. + * + * If the RTS frames are generated by the host system (i.e., not in + * hardware/firmware), the low-level driver uses this function to receive + * the next RTS frame from the 802.11 code. The low-level is responsible + * for calling this function before and RTS frame is needed. + */ +void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + const void *frame, size_t frame_len, + const struct ieee80211_tx_info *frame_txctl, + struct ieee80211_rts *rts); + +/** + * ieee80211_rts_duration - Get the duration field for an RTS frame + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @frame_len: the length of the frame that is going to be protected by the RTS. + * @frame_txctl: &struct ieee80211_tx_info of the frame. + * + * If the RTS is generated in firmware, but the host system must provide + * the duration field, the low-level driver uses this function to receive + * the duration field value in little-endian byteorder. + * + * Return: The duration. + */ +__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, size_t frame_len, + const struct ieee80211_tx_info *frame_txctl); + +/** + * ieee80211_ctstoself_get - CTS-to-self frame generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @frame: pointer to the frame that is going to be protected by the CTS-to-self. + * @frame_len: the frame length (in octets). + * @frame_txctl: &struct ieee80211_tx_info of the frame. + * @cts: The buffer where to store the CTS-to-self frame. + * + * If the CTS-to-self frames are generated by the host system (i.e., not in + * hardware/firmware), the low-level driver uses this function to receive + * the next CTS-to-self frame from the 802.11 code. The low-level is responsible + * for calling this function before and CTS-to-self frame is needed. + */ +void ieee80211_ctstoself_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + const void *frame, size_t frame_len, + const struct ieee80211_tx_info *frame_txctl, + struct ieee80211_cts *cts); + +/** + * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @frame_len: the length of the frame that is going to be protected by the CTS-to-self. + * @frame_txctl: &struct ieee80211_tx_info of the frame. + * + * If the CTS-to-self is generated in firmware, but the host system must provide + * the duration field, the low-level driver uses this function to receive + * the duration field value in little-endian byteorder. + * + * Return: The duration. + */ +__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + size_t frame_len, + const struct ieee80211_tx_info *frame_txctl); + +/** + * ieee80211_generic_frame_duration - Calculate the duration field for a frame + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @band: the band to calculate the frame duration on + * @frame_len: the length of the frame. + * @rate: the rate at which the frame is going to be transmitted. + * + * Calculate the duration field of some generic frame, given its + * length and transmission rate (in 100kbps). + * + * Return: The duration. + */ +__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum ieee80211_band band, + size_t frame_len, + struct ieee80211_rate *rate); + +/** + * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Function for accessing buffered broadcast and multicast frames. If + * hardware/firmware does not implement buffering of broadcast/multicast + * frames when power saving is used, 802.11 code buffers them in the host + * memory. The low-level driver uses this function to fetch next buffered + * frame. In most cases, this is used when generating beacon frame. + * + * Return: A pointer to the next buffered skb or NULL if no more buffered + * frames are available. + * + * Note: buffered frames are returned only after DTIM beacon frame was + * generated with ieee80211_beacon_get() and the low-level driver must thus + * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns + * NULL if the previous generated beacon was not DTIM, so the low-level driver + * does not need to check for DTIM beacons separately and should be able to + * use common code for all beacons. + */ +struct sk_buff * +ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + +/** + * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32 + * + * This function returns the TKIP phase 1 key for the given IV32. + * + * @keyconf: the parameter passed with the set key + * @iv32: IV32 to get the P1K for + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf, + u32 iv32, u16 *p1k); + +/** + * ieee80211_get_tkip_p1k - get a TKIP phase 1 key + * + * This function returns the TKIP phase 1 key for the IV32 taken + * from the given packet. + * + * @keyconf: the parameter passed with the set key + * @skb: the packet to take the IV32 value from that will be encrypted + * with this P1K + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf, + struct sk_buff *skb, u16 *p1k) +{ + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; + const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control); + u32 iv32 = get_unaligned_le32(&data[4]); + + ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k); +} + +/** + * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX + * + * This function returns the TKIP phase 1 key for the given IV32 + * and transmitter address. + * + * @keyconf: the parameter passed with the set key + * @ta: TA that will be used with the key + * @iv32: IV32 to get the P1K for + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf, + const u8 *ta, u32 iv32, u16 *p1k); + +/** + * ieee80211_get_tkip_p2k - get a TKIP phase 2 key + * + * This function computes the TKIP RC4 key for the IV values + * in the packet. + * + * @keyconf: the parameter passed with the set key + * @skb: the packet to take the IV32/IV16 values from that will be + * encrypted with this key + * @p2k: a buffer to which the key will be written, 16 bytes + */ +void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf, + struct sk_buff *skb, u8 *p2k); + +/** + * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys + * + * This function computes the two AES-CMAC sub-keys, based on the + * previously installed master key. + * + * @keyconf: the parameter passed with the set key + * @k1: a buffer to be filled with the 1st sub-key + * @k2: a buffer to be filled with the 2nd sub-key + */ +void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf, + u8 *k1, u8 *k2); + +/** + * struct ieee80211_key_seq - key sequence counter + * + * @tkip: TKIP data, containing IV32 and IV16 in host byte order + * @ccmp: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @aes_cmac: PN data, most significant byte first (big endian, + * reverse order than in packet) + */ +struct ieee80211_key_seq { + union { + struct { + u32 iv32; + u16 iv16; + } tkip; + struct { + u8 pn[6]; + } ccmp; + struct { + u8 pn[6]; + } aes_cmac; + }; +}; + +/** + * ieee80211_get_key_tx_seq - get key TX sequence counter + * + * @keyconf: the parameter passed with the set key + * @seq: buffer to receive the sequence data + * + * This function allows a driver to retrieve the current TX IV/PN + * for the given key. It must not be called if IV generation is + * offloaded to the device. + * + * Note that this function may only be called when no TX processing + * can be done concurrently, for example when queues are stopped + * and the stop has been synchronized. + */ +void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf, + struct ieee80211_key_seq *seq); + +/** + * ieee80211_get_key_rx_seq - get key RX sequence counter + * + * @keyconf: the parameter passed with the set key + * @tid: The TID, or -1 for the management frame value (CCMP only); + * the value on TID 0 is also used for non-QoS frames. For + * CMAC, only TID 0 is valid. + * @seq: buffer to receive the sequence data + * + * This function allows a driver to retrieve the current RX IV/PNs + * for the given key. It must not be called if IV checking is done + * by the device and not by mac80211. + * + * Note that this function may only be called when no RX processing + * can be done concurrently. + */ +void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf, + int tid, struct ieee80211_key_seq *seq); + +/** + * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying + * @vif: virtual interface the rekeying was done on + * @bssid: The BSSID of the AP, for checking association + * @replay_ctr: the new replay counter after GTK rekeying + * @gfp: allocation flags + */ +void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid, + const u8 *replay_ctr, gfp_t gfp); + +/** + * ieee80211_wake_queue - wake specific queue + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @queue: queue number (counted from zero). + * + * Drivers should use this function instead of netif_wake_queue. + */ +void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); + +/** + * ieee80211_stop_queue - stop specific queue + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @queue: queue number (counted from zero). + * + * Drivers should use this function instead of netif_stop_queue. + */ +void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); + +/** + * ieee80211_queue_stopped - test status of the queue + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @queue: queue number (counted from zero). + * + * Drivers should use this function instead of netif_stop_queue. + * + * Return: %true if the queue is stopped. %false otherwise. + */ + +int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue); + +/** + * ieee80211_stop_queues - stop all queues + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * + * Drivers should use this function instead of netif_stop_queue. + */ +void ieee80211_stop_queues(struct ieee80211_hw *hw); + +/** + * ieee80211_wake_queues - wake all queues + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * + * Drivers should use this function instead of netif_wake_queue. + */ +void ieee80211_wake_queues(struct ieee80211_hw *hw); + +/** + * ieee80211_scan_completed - completed hardware scan + * + * When hardware scan offload is used (i.e. the hw_scan() callback is + * assigned) this function needs to be called by the driver to notify + * mac80211 that the scan finished. This function can be called from + * any context, including hardirq context. + * + * @hw: the hardware that finished the scan + * @aborted: set to true if scan was aborted + */ +void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); + +/** + * ieee80211_sched_scan_results - got results from scheduled scan + * + * When a scheduled scan is running, this function needs to be called by the + * driver whenever there are new scan results available. + * + * @hw: the hardware that is performing scheduled scans + */ +void ieee80211_sched_scan_results(struct ieee80211_hw *hw); + +/** + * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped + * + * When a scheduled scan is running, this function can be called by + * the driver if it needs to stop the scan to perform another task. + * Usual scenarios are drivers that cannot continue the scheduled scan + * while associating, for instance. + * + * @hw: the hardware that is performing scheduled scans + */ +void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); + +/** + * enum ieee80211_interface_iteration_flags - interface iteration flags + * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have + * been added to the driver; However, note that during hardware + * reconfiguration (after restart_hw) it will iterate over a new + * interface and over all the existing interfaces even if they + * haven't been re-added to the driver yet. + * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all + * interfaces, even if they haven't been re-added to the driver yet. + */ +enum ieee80211_interface_iteration_flags { + IEEE80211_IFACE_ITER_NORMAL = 0, + IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0), +}; + +/** + * ieee80211_iterate_active_interfaces - iterate active interfaces + * + * This function iterates over the interfaces associated with a given + * hardware that are currently active and calls the callback for them. + * This function allows the iterator function to sleep, when the iterator + * function is atomic @ieee80211_iterate_active_interfaces_atomic can + * be used. + * Does not iterate over a new interface during add_interface(). + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call + * @data: first argument of the iterator function + */ +void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, + u32 iter_flags, + void (*iterator)(void *data, u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** + * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces + * + * This function iterates over the interfaces associated with a given + * hardware that are currently active and calls the callback for them. + * This function requires the iterator callback function to be atomic, + * if that is not desired, use @ieee80211_iterate_active_interfaces instead. + * Does not iterate over a new interface during add_interface(). + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call, cannot sleep + * @data: first argument of the iterator function + */ +void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, + u32 iter_flags, + void (*iterator)(void *data, + u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** + * ieee80211_queue_work - add work onto the mac80211 workqueue + * + * Drivers and mac80211 use this to add work onto the mac80211 workqueue. + * This helper ensures drivers are not queueing work when they should not be. + * + * @hw: the hardware struct for the interface we are adding work for + * @work: the work we want to add onto the mac80211 workqueue + */ +void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work); + +/** + * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue + * + * Drivers and mac80211 use this to queue delayed work onto the mac80211 + * workqueue. + * + * @hw: the hardware struct for the interface we are adding work for + * @dwork: delayable work to queue onto the mac80211 workqueue + * @delay: number of jiffies to wait before queueing + */ +void ieee80211_queue_delayed_work(struct ieee80211_hw *hw, + struct delayed_work *dwork, + unsigned long delay); + +/** + * ieee80211_start_tx_ba_session - Start a tx Block Ack session. + * @sta: the station for which to start a BA session + * @tid: the TID to BA on. + * @timeout: session timeout value (in TUs) + * + * Return: success if addBA request was sent, failure otherwise + * + * Although mac80211/low level driver/user space application can estimate + * the need to start aggregation on a certain RA/TID, the session level + * will be managed by the mac80211. + */ +int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid, + u16 timeout); + +/** + * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. + * @vif: &struct ieee80211_vif pointer from the add_interface callback + * @ra: receiver address of the BA session recipient. + * @tid: the TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session. It can be called + * from any context. + */ +void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, + u16 tid); + +/** + * ieee80211_stop_tx_ba_session - Stop a Block Ack session. + * @sta: the station whose BA session to stop + * @tid: the TID to stop BA. + * + * Return: negative error if the TID is invalid, or no aggregation active + * + * Although mac80211/low level driver/user space application can estimate + * the need to stop aggregation on a certain RA/TID, the session level + * will be managed by the mac80211. + */ +int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid); + +/** + * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. + * @vif: &struct ieee80211_vif pointer from the add_interface callback + * @ra: receiver address of the BA session recipient. + * @tid: the desired TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session tear down. It + * can be called from any context. + */ +void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, + u16 tid); + +/** + * ieee80211_find_sta - find a station + * + * @vif: virtual interface to look for station on + * @addr: station's address + * + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the + * resulting pointer is only valid under RCU lock as well. + */ +struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, + const u8 *addr); + +/** + * ieee80211_find_sta_by_ifaddr - find a station on hardware + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @addr: remote station's address + * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. + * + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the + * resulting pointer is only valid under RCU lock as well. + * + * NOTE: You may pass NULL for localaddr, but then you will just get + * the first STA that matches the remote address 'addr'. + * We can have multiple STA associated with multiple + * logical stations (e.g. consider a station connecting to another + * BSSID on the same AP hardware without disconnecting first). + * In this case, the result of this method with localaddr NULL + * is not reliable. + * + * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible. + */ +struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw, + const u8 *addr, + const u8 *localaddr); + +/** + * ieee80211_sta_block_awake - block station from waking up + * @hw: the hardware + * @pubsta: the station + * @block: whether to block or unblock + * + * Some devices require that all frames that are on the queues + * for a specific station that went to sleep are flushed before + * a poll response or frames after the station woke up can be + * delivered to that it. Note that such frames must be rejected + * by the driver as filtered, with the appropriate status flag. + * + * This function allows implementing this mode in a race-free + * manner. + * + * To do this, a driver must keep track of the number of frames + * still enqueued for a specific station. If this number is not + * zero when the station goes to sleep, the driver must call + * this function to force mac80211 to consider the station to + * be asleep regardless of the station's actual state. Once the + * number of outstanding frames reaches zero, the driver must + * call this function again to unblock the station. That will + * cause mac80211 to be able to send ps-poll responses, and if + * the station queried in the meantime then frames will also + * be sent out as a result of this. Additionally, the driver + * will be notified that the station woke up some time after + * it is unblocked, regardless of whether the station actually + * woke up while blocked or not. + */ +void ieee80211_sta_block_awake(struct ieee80211_hw *hw, + struct ieee80211_sta *pubsta, bool block); + +/** + * ieee80211_sta_eosp - notify mac80211 about end of SP + * @pubsta: the station + * + * When a device transmits frames in a way that it can't tell + * mac80211 in the TX status about the EOSP, it must clear the + * %IEEE80211_TX_STATUS_EOSP bit and call this function instead. + * This applies for PS-Poll as well as uAPSD. + * + * Note that just like with _tx_status() and _rx() drivers must + * not mix calls to irqsafe/non-irqsafe versions, this function + * must not be mixed with those either. Use the all irqsafe, or + * all non-irqsafe, don't mix! + * + * NB: the _irqsafe version of this function doesn't exist, no + * driver needs it right now. Don't call this function if + * you'd need the _irqsafe version, look at the git history + * and restore the _irqsafe version! + */ +void ieee80211_sta_eosp(struct ieee80211_sta *pubsta); + +/** + * ieee80211_iter_keys - iterate keys programmed into the device + * @hw: pointer obtained from ieee80211_alloc_hw() + * @vif: virtual interface to iterate, may be %NULL for all + * @iter: iterator function that will be called for each key + * @iter_data: custom data to pass to the iterator function + * + * This function can be used to iterate all the keys known to + * mac80211, even those that weren't previously programmed into + * the device. This is intended for use in WoWLAN if the device + * needs reprogramming of the keys during suspend. Note that due + * to locking reasons, it is also only safe to call this at few + * spots since it must hold the RTNL and be able to sleep. + * + * The order in which the keys are iterated matches the order + * in which they were originally installed and handed to the + * set_key callback. + */ +void ieee80211_iter_keys(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + void (*iter)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct ieee80211_key_conf *key, + void *data), + void *iter_data); + +/** + * ieee80211_iter_chan_contexts_atomic - iterate channel contexts + * @hw: pointre obtained from ieee80211_alloc_hw(). + * @iter: iterator function + * @iter_data: data passed to iterator function + * + * Iterate all active channel contexts. This function is atomic and + * doesn't acquire any locks internally that might be held in other + * places while calling into the driver. + * + * The iterator will not find a context that's being added (during + * the driver callback to add it) but will find it while it's being + * removed. + * + * Note that during hardware restart, all contexts that existed + * before the restart are considered already present so will be + * found while iterating, whether they've been re-added already + * or not. + */ +void ieee80211_iter_chan_contexts_atomic( + struct ieee80211_hw *hw, + void (*iter)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *chanctx_conf, + void *data), + void *iter_data); + +/** + * ieee80211_ap_probereq_get - retrieve a Probe Request template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Creates a Probe Request template which can, for example, be uploaded to + * hardware. The template is filled with bssid, ssid and supported rate + * information. This function must only be called from within the + * .bss_info_changed callback function and only in managed mode. The function + * is only useful when the interface is associated, otherwise it will return + * %NULL. + * + * Return: The Probe Request template. %NULL on error. + */ +struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** + * ieee80211_beacon_loss - inform hardware does not receive beacons + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and + * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the + * hardware is not receiving beacons with this function. + */ +void ieee80211_beacon_loss(struct ieee80211_vif *vif); + +/** + * ieee80211_connection_loss - inform hardware has lost connection to the AP + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and + * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver + * needs to inform if the connection to the AP has been lost. + * The function may also be called if the connection needs to be terminated + * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set. + * + * This function will cause immediate change to disassociated state, + * without connection recovery attempts. + */ +void ieee80211_connection_loss(struct ieee80211_vif *vif); + +/** + * ieee80211_resume_disconnect - disconnect from AP after resume + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Instructs mac80211 to disconnect from the AP after resume. + * Drivers can use this after WoWLAN if they know that the + * connection cannot be kept up, for example because keys were + * used while the device was asleep but the replay counters or + * similar cannot be retrieved from the device during resume. + * + * Note that due to implementation issues, if the driver uses + * the reconfiguration functionality during resume the interface + * will still be added as associated first during resume and then + * disconnect normally later. + * + * This function can only be called from the resume callback and + * the driver must not be holding any of its own locks while it + * calls this function, or at least not any locks it needs in the + * key configuration paths (if it supports HW crypto). + */ +void ieee80211_resume_disconnect(struct ieee80211_vif *vif); + +/** + * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring + * rssi threshold triggered + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @rssi_event: the RSSI trigger event type + * @gfp: context flags + * + * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality + * monitoring is configured with an rssi threshold, the driver will inform + * whenever the rssi level reaches the threshold. + */ +void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, + enum nl80211_cqm_rssi_threshold_event rssi_event, + gfp_t gfp); + +/** + * ieee80211_radar_detected - inform that a radar was detected + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_radar_detected(struct ieee80211_hw *hw); + +/** + * ieee80211_chswitch_done - Complete channel switch process + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @success: make the channel switch successful or not + * + * Complete the channel switch post-process: set the new operational channel + * and wake up the suspended queues. + */ +void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success); + +/** + * ieee80211_request_smps - request SM PS transition + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @smps_mode: new SM PS mode + * + * This allows the driver to request an SM PS transition in managed + * mode. This is useful when the driver has more information than + * the stack about possible interference, for example by bluetooth. + */ +void ieee80211_request_smps(struct ieee80211_vif *vif, + enum ieee80211_smps_mode smps_mode); + +/** + * ieee80211_ready_on_channel - notification of remain-on-channel start + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_ready_on_channel(struct ieee80211_hw *hw); + +/** + * ieee80211_remain_on_channel_expired - remain_on_channel duration expired + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw); + +/** + * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions + * + * in order not to harm the system performance and user experience, the device + * may request not to allow any rx ba session and tear down existing rx ba + * sessions based on system constraints such as periodic BT activity that needs + * to limit wlan activity (eg.sco or a2dp)." + * in such cases, the intention is to limit the duration of the rx ppdu and + * therefore prevent the peer device to use a-mpdu aggregation. + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ba_rx_bitmap: Bit map of open rx ba per tid + * @addr: & to bssid mac address + */ +void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap, + const u8 *addr); + +/** + * ieee80211_send_bar - send a BlockAckReq frame + * + * can be used to flush pending frames from the peer's aggregation reorder + * buffer. + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ra: the peer's destination address + * @tid: the TID of the aggregation session + * @ssn: the new starting sequence number for the receiver + */ +void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn); + +/* Rate control API */ + +/** + * struct ieee80211_tx_rate_control - rate control information for/from RC algo + * + * @hw: The hardware the algorithm is invoked for. + * @sband: The band this frame is being transmitted on. + * @bss_conf: the current BSS configuration + * @skb: the skb that will be transmitted, the control information in it needs + * to be filled in + * @reported_rate: The rate control algorithm can fill this in to indicate + * which rate should be reported to userspace as the current rate and + * used for rate calculations in the mesh network. + * @rts: whether RTS will be used for this frame because it is longer than the + * RTS threshold + * @short_preamble: whether mac80211 will request short-preamble transmission + * if the selected rate supports it + * @max_rate_idx: user-requested maximum (legacy) rate + * (deprecated; this will be removed once drivers get updated to use + * rate_idx_mask) + * @rate_idx_mask: user-requested (legacy) rate mask + * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use) + * @bss: whether this frame is sent out in AP or IBSS mode + */ +struct ieee80211_tx_rate_control { + struct ieee80211_hw *hw; + struct ieee80211_supported_band *sband; + struct ieee80211_bss_conf *bss_conf; + struct sk_buff *skb; + struct ieee80211_tx_rate reported_rate; + bool rts, short_preamble; + u8 max_rate_idx; + u32 rate_idx_mask; + u8 *rate_idx_mcs_mask; + bool bss; +}; + +struct rate_control_ops { + struct module *module; + const char *name; + void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir); + void (*free)(void *priv); + + void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp); + void (*rate_init)(void *priv, struct ieee80211_supported_band *sband, + struct ieee80211_sta *sta, void *priv_sta); + void (*rate_update)(void *priv, struct ieee80211_supported_band *sband, + struct ieee80211_sta *sta, void *priv_sta, + u32 changed); + void (*free_sta)(void *priv, struct ieee80211_sta *sta, + void *priv_sta); + + void (*tx_status)(void *priv, struct ieee80211_supported_band *sband, + struct ieee80211_sta *sta, void *priv_sta, + struct sk_buff *skb); + void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta, + struct ieee80211_tx_rate_control *txrc); + + void (*add_sta_debugfs)(void *priv, void *priv_sta, + struct dentry *dir); + void (*remove_sta_debugfs)(void *priv, void *priv_sta); +}; + +static inline int rate_supported(struct ieee80211_sta *sta, + enum ieee80211_band band, + int index) +{ + return (sta == NULL || sta->supp_rates[band] & BIT(index)); +} + +/** + * rate_control_send_low - helper for drivers for management/no-ack frames + * + * Rate control algorithms that agree to use the lowest rate to + * send management frames and NO_ACK data with the respective hw + * retries should use this in the beginning of their mac80211 get_rate + * callback. If true is returned the rate control can simply return. + * If false is returned we guarantee that sta and sta and priv_sta is + * not null. + * + * Rate control algorithms wishing to do more intelligent selection of + * rate for multicast/broadcast frames may choose to not use this. + * + * @sta: &struct ieee80211_sta pointer to the target destination. Note + * that this may be null. + * @priv_sta: private rate control structure. This may be null. + * @txrc: rate control information we sholud populate for mac80211. + */ +bool rate_control_send_low(struct ieee80211_sta *sta, + void *priv_sta, + struct ieee80211_tx_rate_control *txrc); + + +static inline s8 +rate_lowest_index(struct ieee80211_supported_band *sband, + struct ieee80211_sta *sta) +{ + int i; + + for (i = 0; i < sband->n_bitrates; i++) + if (rate_supported(sta, sband->band, i)) + return i; + + /* warn when we cannot find a rate. */ + WARN_ON_ONCE(1); + + /* and return 0 (the lowest index) */ + return 0; +} + +static inline +bool rate_usable_index_exists(struct ieee80211_supported_band *sband, + struct ieee80211_sta *sta) +{ + unsigned int i; + + for (i = 0; i < sband->n_bitrates; i++) + if (rate_supported(sta, sband->band, i)) + return true; + return false; +} + +/** + * rate_control_set_rates - pass the sta rate selection to mac80211/driver + * + * When not doing a rate control probe to test rates, rate control should pass + * its rate selection to mac80211. If the driver supports receiving a station + * rate table, it will use it to ensure that frames are always sent based on + * the most recent rate control module decision. + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @pubsta: &struct ieee80211_sta pointer to the target destination. + * @rates: new tx rate set to be used for this station. + */ +int rate_control_set_rates(struct ieee80211_hw *hw, + struct ieee80211_sta *pubsta, + struct ieee80211_sta_rates *rates); + +int ieee80211_rate_control_register(struct rate_control_ops *ops); +void ieee80211_rate_control_unregister(struct rate_control_ops *ops); + +static inline bool +conf_is_ht20(struct ieee80211_conf *conf) +{ + return conf->chandef.width == NL80211_CHAN_WIDTH_20; +} + +static inline bool +conf_is_ht40_minus(struct ieee80211_conf *conf) +{ + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 < conf->chandef.chan->center_freq; +} + +static inline bool +conf_is_ht40_plus(struct ieee80211_conf *conf) +{ + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 > conf->chandef.chan->center_freq; +} + +static inline bool +conf_is_ht40(struct ieee80211_conf *conf) +{ + return conf->chandef.width == NL80211_CHAN_WIDTH_40; +} + +static inline bool +conf_is_ht(struct ieee80211_conf *conf) +{ + return conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT; +} + +static inline enum nl80211_iftype +ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p) +{ + if (p2p) { + switch (type) { + case NL80211_IFTYPE_STATION: + return NL80211_IFTYPE_P2P_CLIENT; + case NL80211_IFTYPE_AP: + return NL80211_IFTYPE_P2P_GO; + default: + break; + } + } + return type; +} + +static inline enum nl80211_iftype +ieee80211_vif_type_p2p(struct ieee80211_vif *vif) +{ + return ieee80211_iftype_p2p(vif->type, vif->p2p); +} + +void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif, + int rssi_min_thold, + int rssi_max_thold); + +void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif); + +/** + * ieee80211_ave_rssi - report the average RSSI for the specified interface + * + * @vif: the specified virtual interface + * + * Note: This function assumes that the given vif is valid. + * + * Return: The average RSSI value for the requested interface, or 0 if not + * applicable. + */ +int ieee80211_ave_rssi(struct ieee80211_vif *vif); + +/** + * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup + * @vif: virtual interface + * @wakeup: wakeup reason(s) + * @gfp: allocation flags + * + * See cfg80211_report_wowlan_wakeup(). + */ +void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif, + struct cfg80211_wowlan_wakeup *wakeup, + gfp_t gfp); + +#endif /* MAC80211_H */ |