diff options
Diffstat (limited to 'include/media/tuner-types.h')
| -rw-r--r-- | include/media/tuner-types.h | 131 |
1 files changed, 131 insertions, 0 deletions
diff --git a/include/media/tuner-types.h b/include/media/tuner-types.h new file mode 100644 index 0000000..ab03c53 --- /dev/null +++ b/include/media/tuner-types.h @@ -0,0 +1,131 @@ +/* + * descriptions for simple tuners. + */ + +#ifndef __TUNER_TYPES_H__ +#define __TUNER_TYPES_H__ + +enum param_type { + TUNER_PARAM_TYPE_RADIO, + TUNER_PARAM_TYPE_PAL, + TUNER_PARAM_TYPE_SECAM, + TUNER_PARAM_TYPE_NTSC, + TUNER_PARAM_TYPE_DIGITAL, +}; + +struct tuner_range { + unsigned short limit; + unsigned char config; + unsigned char cb; +}; + +struct tuner_params { + enum param_type type; + + /* Many Philips based tuners have a comment like this in their + * datasheet: + * + * For channel selection involving band switching, and to ensure + * smooth tuning to the desired channel without causing + * unnecessary charge pump action, it is recommended to consider + * the difference between wanted channel frequency and the + * current channel frequency. Unnecessary charge pump action + * will result in very low tuning voltage which may drive the + * oscillator to extreme conditions. + * + * Set cb_first_if_lower_freq to 1, if this check is + * required for this tuner. + * + * I tested this for PAL by first setting the TV frequency to + * 203 MHz and then switching to 96.6 MHz FM radio. The result was + * static unless the control byte was sent first. + */ + unsigned int cb_first_if_lower_freq:1; + /* Set to 1 if this tuner uses a tda9887 */ + unsigned int has_tda9887:1; + /* Many Philips tuners use tda9887 PORT1 to select the FM radio + sensitivity. If this setting is 1, then set PORT1 to 1 to + get proper FM reception. */ + unsigned int port1_fm_high_sensitivity:1; + /* Some Philips tuners use tda9887 PORT2 to select the FM radio + sensitivity. If this setting is 1, then set PORT2 to 1 to + get proper FM reception. */ + unsigned int port2_fm_high_sensitivity:1; + /* Some Philips tuners use tda9887 cGainNormal to select the FM radio + sensitivity. If this setting is 1, e register will use cGainNormal + instead of cGainLow. */ + unsigned int fm_gain_normal:1; + /* Most tuners with a tda9887 use QSS mode. Some (cheaper) tuners + use Intercarrier mode. If this setting is 1, then the tuner + needs to be set to intercarrier mode. */ + unsigned int intercarrier_mode:1; + /* This setting sets the default value for PORT1. + 0 means inactive, 1 means active. Note: the actual bit + value written to the tda9887 is inverted. So a 0 here + means a 1 in the B6 bit. */ + unsigned int port1_active:1; + /* This setting sets the default value for PORT2. + 0 means inactive, 1 means active. Note: the actual bit + value written to the tda9887 is inverted. So a 0 here + means a 1 in the B7 bit. */ + unsigned int port2_active:1; + /* Sometimes PORT1 is inverted when the SECAM-L' standard is selected. + Set this bit to 1 if this is needed. */ + unsigned int port1_invert_for_secam_lc:1; + /* Sometimes PORT2 is inverted when the SECAM-L' standard is selected. + Set this bit to 1 if this is needed. */ + unsigned int port2_invert_for_secam_lc:1; + /* Some cards require PORT1 to be 1 for mono Radio FM and 0 for stereo. */ + unsigned int port1_set_for_fm_mono:1; + /* Select 18% (or according to datasheet 0%) L standard PLL gating, + vs the driver default of 36%. */ + unsigned int default_pll_gating_18:1; + /* IF to use in radio mode. Tuners with a separate radio IF filter + seem to use 10.7, while those without use 33.3 for PAL/SECAM tuners + and 41.3 for NTSC tuners. 0 = 10.7, 1 = 33.3, 2 = 41.3 */ + unsigned int radio_if:2; + /* Default tda9887 TOP value in dB for the low band. Default is 0. + Range: -16:+15 */ + signed int default_top_low:5; + /* Default tda9887 TOP value in dB for the mid band. Default is 0. + Range: -16:+15 */ + signed int default_top_mid:5; + /* Default tda9887 TOP value in dB for the high band. Default is 0. + Range: -16:+15 */ + signed int default_top_high:5; + /* Default tda9887 TOP value in dB for SECAM-L/L' for the low band. + Default is 0. Several tuners require a different TOP value for + the SECAM-L/L' standards. Range: -16:+15 */ + signed int default_top_secam_low:5; + /* Default tda9887 TOP value in dB for SECAM-L/L' for the mid band. + Default is 0. Several tuners require a different TOP value for + the SECAM-L/L' standards. Range: -16:+15 */ + signed int default_top_secam_mid:5; + /* Default tda9887 TOP value in dB for SECAM-L/L' for the high band. + Default is 0. Several tuners require a different TOP value for + the SECAM-L/L' standards. Range: -16:+15 */ + signed int default_top_secam_high:5; + + u16 iffreq; + + unsigned int count; + struct tuner_range *ranges; +}; + +struct tunertype { + char *name; + unsigned int count; + struct tuner_params *params; + + u16 min; + u16 max; + u32 stepsize; + + u8 *initdata; + u8 *sleepdata; +}; + +extern struct tunertype tuners[]; +extern unsigned const int tuner_count; + +#endif |