diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath9k/pci.c')
| -rw-r--r-- | drivers/net/wireless/ath/ath9k/pci.c | 350 |
1 files changed, 350 insertions, 0 deletions
diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c new file mode 100644 index 0000000..547340b --- /dev/null +++ b/drivers/net/wireless/ath/ath9k/pci.c @@ -0,0 +1,350 @@ +/* + * Copyright (c) 2008-2011 Atheros Communications Inc. + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/nl80211.h> +#include <linux/pci.h> +#include <linux/pci-aspm.h> +#include <linux/ath9k_platform.h> +#include <linux/module.h> +#include "ath9k.h" + +static DEFINE_PCI_DEVICE_TABLE(ath_pci_id_table) = { + { PCI_VDEVICE(ATHEROS, 0x0023) }, /* PCI */ + { PCI_VDEVICE(ATHEROS, 0x0024) }, /* PCI-E */ + { PCI_VDEVICE(ATHEROS, 0x0027) }, /* PCI */ + { PCI_VDEVICE(ATHEROS, 0x0029) }, /* PCI */ + { PCI_VDEVICE(ATHEROS, 0x002A) }, /* PCI-E */ + { PCI_VDEVICE(ATHEROS, 0x002B) }, /* PCI-E */ + { PCI_VDEVICE(ATHEROS, 0x002C) }, /* PCI-E 802.11n bonded out */ + { PCI_VDEVICE(ATHEROS, 0x002D) }, /* PCI */ + { PCI_VDEVICE(ATHEROS, 0x002E) }, /* PCI-E */ + { PCI_VDEVICE(ATHEROS, 0x0030) }, /* PCI-E AR9300 */ + { PCI_VDEVICE(ATHEROS, 0x0032) }, /* PCI-E AR9485 */ + { PCI_VDEVICE(ATHEROS, 0x0033) }, /* PCI-E AR9580 */ + { PCI_VDEVICE(ATHEROS, 0x0034) }, /* PCI-E AR9462 */ + { PCI_VDEVICE(ATHEROS, 0x0037) }, /* PCI-E AR1111/AR9485 */ + { PCI_VDEVICE(ATHEROS, 0x0036) }, /* PCI-E AR9565 */ + { 0 } +}; + + +/* return bus cachesize in 4B word units */ +static void ath_pci_read_cachesize(struct ath_common *common, int *csz) +{ + struct ath_softc *sc = (struct ath_softc *) common->priv; + u8 u8tmp; + + pci_read_config_byte(to_pci_dev(sc->dev), PCI_CACHE_LINE_SIZE, &u8tmp); + *csz = (int)u8tmp; + + /* + * This check was put in to avoid "unpleasant" consequences if + * the bootrom has not fully initialized all PCI devices. + * Sometimes the cache line size register is not set + */ + + if (*csz == 0) + *csz = DEFAULT_CACHELINE >> 2; /* Use the default size */ +} + +static bool ath_pci_eeprom_read(struct ath_common *common, u32 off, u16 *data) +{ + struct ath_softc *sc = (struct ath_softc *) common->priv; + struct ath9k_platform_data *pdata = sc->dev->platform_data; + + if (pdata) { + if (off >= (ARRAY_SIZE(pdata->eeprom_data))) { + ath_err(common, + "%s: eeprom read failed, offset %08x is out of range\n", + __func__, off); + } + + *data = pdata->eeprom_data[off]; + } else { + struct ath_hw *ah = (struct ath_hw *) common->ah; + + common->ops->read(ah, AR5416_EEPROM_OFFSET + + (off << AR5416_EEPROM_S)); + + if (!ath9k_hw_wait(ah, + AR_EEPROM_STATUS_DATA, + AR_EEPROM_STATUS_DATA_BUSY | + AR_EEPROM_STATUS_DATA_PROT_ACCESS, 0, + AH_WAIT_TIMEOUT)) { + return false; + } + + *data = MS(common->ops->read(ah, AR_EEPROM_STATUS_DATA), + AR_EEPROM_STATUS_DATA_VAL); + } + + return true; +} + +/* Need to be called after we discover btcoex capabilities */ +static void ath_pci_aspm_init(struct ath_common *common) +{ + struct ath_softc *sc = (struct ath_softc *) common->priv; + struct ath_hw *ah = sc->sc_ah; + struct pci_dev *pdev = to_pci_dev(sc->dev); + struct pci_dev *parent; + u16 aspm; + + if (!ah->is_pciexpress) + return; + + parent = pdev->bus->self; + if (!parent) + return; + + if ((ath9k_hw_get_btcoex_scheme(ah) != ATH_BTCOEX_CFG_NONE) && + (AR_SREV_9285(ah))) { + /* Bluetooth coexistence requires disabling ASPM. */ + pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, + PCI_EXP_LNKCTL_ASPM_L0S | PCI_EXP_LNKCTL_ASPM_L1); + + /* + * Both upstream and downstream PCIe components should + * have the same ASPM settings. + */ + pcie_capability_clear_word(parent, PCI_EXP_LNKCTL, + PCI_EXP_LNKCTL_ASPM_L0S | PCI_EXP_LNKCTL_ASPM_L1); + + ath_info(common, "Disabling ASPM since BTCOEX is enabled\n"); + return; + } + + pcie_capability_read_word(parent, PCI_EXP_LNKCTL, &aspm); + if (aspm & (PCI_EXP_LNKCTL_ASPM_L0S | PCI_EXP_LNKCTL_ASPM_L1)) { + ah->aspm_enabled = true; + /* Initialize PCIe PM and SERDES registers. */ + ath9k_hw_configpcipowersave(ah, false); + ath_info(common, "ASPM enabled: 0x%x\n", aspm); + } +} + +static const struct ath_bus_ops ath_pci_bus_ops = { + .ath_bus_type = ATH_PCI, + .read_cachesize = ath_pci_read_cachesize, + .eeprom_read = ath_pci_eeprom_read, + .aspm_init = ath_pci_aspm_init, +}; + +static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) +{ + struct ath_softc *sc; + struct ieee80211_hw *hw; + u8 csz; + u32 val; + int ret = 0; + char hw_name[64]; + + if (pcim_enable_device(pdev)) + return -EIO; + + ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); + if (ret) { + pr_err("32-bit DMA not available\n"); + return ret; + } + + ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); + if (ret) { + pr_err("32-bit DMA consistent DMA enable failed\n"); + return ret; + } + + /* + * Cache line size is used to size and align various + * structures used to communicate with the hardware. + */ + pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz); + if (csz == 0) { + /* + * Linux 2.4.18 (at least) writes the cache line size + * register as a 16-bit wide register which is wrong. + * We must have this setup properly for rx buffer + * DMA to work so force a reasonable value here if it + * comes up zero. + */ + csz = L1_CACHE_BYTES / sizeof(u32); + pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz); + } + /* + * The default setting of latency timer yields poor results, + * set it to the value used by other systems. It may be worth + * tweaking this setting more. + */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8); + + pci_set_master(pdev); + + /* + * Disable the RETRY_TIMEOUT register (0x41) to keep + * PCI Tx retries from interfering with C3 CPU state. + */ + pci_read_config_dword(pdev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); + + ret = pcim_iomap_regions(pdev, BIT(0), "ath9k"); + if (ret) { + dev_err(&pdev->dev, "PCI memory region reserve error\n"); + return -ENODEV; + } + + hw = ieee80211_alloc_hw(sizeof(struct ath_softc), &ath9k_ops); + if (!hw) { + dev_err(&pdev->dev, "No memory for ieee80211_hw\n"); + return -ENOMEM; + } + + SET_IEEE80211_DEV(hw, &pdev->dev); + pci_set_drvdata(pdev, hw); + + sc = hw->priv; + sc->hw = hw; + sc->dev = &pdev->dev; + sc->mem = pcim_iomap_table(pdev)[0]; + + /* Will be cleared in ath9k_start() */ + set_bit(SC_OP_INVALID, &sc->sc_flags); + + ret = request_irq(pdev->irq, ath_isr, IRQF_SHARED, "ath9k", sc); + if (ret) { + dev_err(&pdev->dev, "request_irq failed\n"); + goto err_irq; + } + + sc->irq = pdev->irq; + + ret = ath9k_init_device(id->device, sc, &ath_pci_bus_ops); + if (ret) { + dev_err(&pdev->dev, "Failed to initialize device\n"); + goto err_init; + } + + ath9k_hw_name(sc->sc_ah, hw_name, sizeof(hw_name)); + wiphy_info(hw->wiphy, "%s mem=0x%lx, irq=%d\n", + hw_name, (unsigned long)sc->mem, pdev->irq); + + return 0; + +err_init: + free_irq(sc->irq, sc); +err_irq: + ieee80211_free_hw(hw); + return ret; +} + +static void ath_pci_remove(struct pci_dev *pdev) +{ + struct ieee80211_hw *hw = pci_get_drvdata(pdev); + struct ath_softc *sc = hw->priv; + + if (!is_ath9k_unloaded) + sc->sc_ah->ah_flags |= AH_UNPLUGGED; + ath9k_deinit_device(sc); + free_irq(sc->irq, sc); + ieee80211_free_hw(sc->hw); +} + +#ifdef CONFIG_PM_SLEEP + +static int ath_pci_suspend(struct device *device) +{ + struct pci_dev *pdev = to_pci_dev(device); + struct ieee80211_hw *hw = pci_get_drvdata(pdev); + struct ath_softc *sc = hw->priv; + + if (sc->wow_enabled) + return 0; + + /* The device has to be moved to FULLSLEEP forcibly. + * Otherwise the chip never moved to full sleep, + * when no interface is up. + */ + ath9k_stop_btcoex(sc); + ath9k_hw_disable(sc->sc_ah); + ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_FULL_SLEEP); + + return 0; +} + +static int ath_pci_resume(struct device *device) +{ + struct pci_dev *pdev = to_pci_dev(device); + struct ieee80211_hw *hw = pci_get_drvdata(pdev); + struct ath_softc *sc = hw->priv; + struct ath_hw *ah = sc->sc_ah; + struct ath_common *common = ath9k_hw_common(ah); + u32 val; + + /* + * Suspend/Resume resets the PCI configuration space, so we have to + * re-disable the RETRY_TIMEOUT register (0x41) to keep + * PCI Tx retries from interfering with C3 CPU state + */ + pci_read_config_dword(pdev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); + + ath_pci_aspm_init(common); + ah->reset_power_on = false; + + return 0; +} + +compat_pci_suspend(ath_pci_suspend); +compat_pci_resume(ath_pci_resume); + +static SIMPLE_DEV_PM_OPS(ath9k_pm_ops, ath_pci_suspend, ath_pci_resume); + +#define ATH9K_PM_OPS (&ath9k_pm_ops) + +#else /* !CONFIG_PM_SLEEP */ + +#define ATH9K_PM_OPS NULL + +#endif /* !CONFIG_PM_SLEEP */ + + +MODULE_DEVICE_TABLE(pci, ath_pci_id_table); + +static struct pci_driver ath_pci_driver = { + .name = "ath9k", + .id_table = ath_pci_id_table, + .probe = ath_pci_probe, + .remove = ath_pci_remove, +#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,29)) + .driver.pm = ATH9K_PM_OPS, +#elif defined(CONFIG_PM_SLEEP) + .suspend = ath_pci_suspend_compat, + .resume = ath_pci_resume_compat, +#endif +}; + +int ath_pci_init(void) +{ + return pci_register_driver(&ath_pci_driver); +} + +void ath_pci_exit(void) +{ + pci_unregister_driver(&ath_pci_driver); +} |