diff options
Diffstat (limited to 'drivers/media/platform/marvell-ccic/mcam-core.c')
| -rw-r--r-- | drivers/media/platform/marvell-ccic/mcam-core.c | 1838 |
1 files changed, 1838 insertions, 0 deletions
diff --git a/drivers/media/platform/marvell-ccic/mcam-core.c b/drivers/media/platform/marvell-ccic/mcam-core.c new file mode 100644 index 0000000..12da293 --- /dev/null +++ b/drivers/media/platform/marvell-ccic/mcam-core.c @@ -0,0 +1,1838 @@ +/* + * The Marvell camera core. This device appears in a number of settings, + * so it needs platform-specific support outside of the core. + * + * Copyright 2011 Jonathan Corbet corbet@lwn.net + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/fs.h> +#include <linux/mm.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/spinlock.h> +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/wait.h> +#include <linux/list.h> +#include <linux/dma-mapping.h> +#include <linux/delay.h> +#include <linux/vmalloc.h> +#include <linux/io.h> +#include <linux/videodev2.h> +#include <media/v4l2-device.h> +#include <media/v4l2-ioctl.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-chip-ident.h> +#include <media/ov7670.h> +#include <media/videobuf2-vmalloc.h> +#include <media/videobuf2-dma-contig.h> +#include <media/videobuf2-dma-sg.h> + +#include "mcam-core.h" + +#ifdef MCAM_MODE_VMALLOC +/* + * Internal DMA buffer management. Since the controller cannot do S/G I/O, + * we must have physically contiguous buffers to bring frames into. + * These parameters control how many buffers we use, whether we + * allocate them at load time (better chance of success, but nails down + * memory) or when somebody tries to use the camera (riskier), and, + * for load-time allocation, how big they should be. + * + * The controller can cycle through three buffers. We could use + * more by flipping pointers around, but it probably makes little + * sense. + */ + +static bool alloc_bufs_at_read; +module_param(alloc_bufs_at_read, bool, 0444); +MODULE_PARM_DESC(alloc_bufs_at_read, + "Non-zero value causes DMA buffers to be allocated when the " + "video capture device is read, rather than at module load " + "time. This saves memory, but decreases the chances of " + "successfully getting those buffers. This parameter is " + "only used in the vmalloc buffer mode"); + +static int n_dma_bufs = 3; +module_param(n_dma_bufs, uint, 0644); +MODULE_PARM_DESC(n_dma_bufs, + "The number of DMA buffers to allocate. Can be either two " + "(saves memory, makes timing tighter) or three."); + +static int dma_buf_size = VGA_WIDTH * VGA_HEIGHT * 2; /* Worst case */ +module_param(dma_buf_size, uint, 0444); +MODULE_PARM_DESC(dma_buf_size, + "The size of the allocated DMA buffers. If actual operating " + "parameters require larger buffers, an attempt to reallocate " + "will be made."); +#else /* MCAM_MODE_VMALLOC */ +static const bool alloc_bufs_at_read = 0; +static const int n_dma_bufs = 3; /* Used by S/G_PARM */ +#endif /* MCAM_MODE_VMALLOC */ + +static bool flip; +module_param(flip, bool, 0444); +MODULE_PARM_DESC(flip, + "If set, the sensor will be instructed to flip the image " + "vertically."); + +static int buffer_mode = -1; +module_param(buffer_mode, int, 0444); +MODULE_PARM_DESC(buffer_mode, + "Set the buffer mode to be used; default is to go with what " + "the platform driver asks for. Set to 0 for vmalloc, 1 for " + "DMA contiguous."); + +/* + * Status flags. Always manipulated with bit operations. + */ +#define CF_BUF0_VALID 0 /* Buffers valid - first three */ +#define CF_BUF1_VALID 1 +#define CF_BUF2_VALID 2 +#define CF_DMA_ACTIVE 3 /* A frame is incoming */ +#define CF_CONFIG_NEEDED 4 /* Must configure hardware */ +#define CF_SINGLE_BUFFER 5 /* Running with a single buffer */ +#define CF_SG_RESTART 6 /* SG restart needed */ + +#define sensor_call(cam, o, f, args...) \ + v4l2_subdev_call(cam->sensor, o, f, ##args) + +static struct mcam_format_struct { + __u8 *desc; + __u32 pixelformat; + int bpp; /* Bytes per pixel */ + enum v4l2_mbus_pixelcode mbus_code; +} mcam_formats[] = { + { + .desc = "YUYV 4:2:2", + .pixelformat = V4L2_PIX_FMT_YUYV, + .mbus_code = V4L2_MBUS_FMT_YUYV8_2X8, + .bpp = 2, + }, + { + .desc = "RGB 444", + .pixelformat = V4L2_PIX_FMT_RGB444, + .mbus_code = V4L2_MBUS_FMT_RGB444_2X8_PADHI_LE, + .bpp = 2, + }, + { + .desc = "RGB 565", + .pixelformat = V4L2_PIX_FMT_RGB565, + .mbus_code = V4L2_MBUS_FMT_RGB565_2X8_LE, + .bpp = 2, + }, + { + .desc = "Raw RGB Bayer", + .pixelformat = V4L2_PIX_FMT_SBGGR8, + .mbus_code = V4L2_MBUS_FMT_SBGGR8_1X8, + .bpp = 1 + }, +}; +#define N_MCAM_FMTS ARRAY_SIZE(mcam_formats) + +static struct mcam_format_struct *mcam_find_format(u32 pixelformat) +{ + unsigned i; + + for (i = 0; i < N_MCAM_FMTS; i++) + if (mcam_formats[i].pixelformat == pixelformat) + return mcam_formats + i; + /* Not found? Then return the first format. */ + return mcam_formats; +} + +/* + * The default format we use until somebody says otherwise. + */ +static const struct v4l2_pix_format mcam_def_pix_format = { + .width = VGA_WIDTH, + .height = VGA_HEIGHT, + .pixelformat = V4L2_PIX_FMT_YUYV, + .field = V4L2_FIELD_NONE, + .bytesperline = VGA_WIDTH*2, + .sizeimage = VGA_WIDTH*VGA_HEIGHT*2, +}; + +static const enum v4l2_mbus_pixelcode mcam_def_mbus_code = + V4L2_MBUS_FMT_YUYV8_2X8; + + +/* + * The two-word DMA descriptor format used by the Armada 610 and like. There + * Is a three-word format as well (set C1_DESC_3WORD) where the third + * word is a pointer to the next descriptor, but we don't use it. Two-word + * descriptors have to be contiguous in memory. + */ +struct mcam_dma_desc { + u32 dma_addr; + u32 segment_len; +}; + +/* + * Our buffer type for working with videobuf2. Note that the vb2 + * developers have decreed that struct vb2_buffer must be at the + * beginning of this structure. + */ +struct mcam_vb_buffer { + struct vb2_buffer vb_buf; + struct list_head queue; + struct mcam_dma_desc *dma_desc; /* Descriptor virtual address */ + dma_addr_t dma_desc_pa; /* Descriptor physical address */ + int dma_desc_nent; /* Number of mapped descriptors */ +}; + +static inline struct mcam_vb_buffer *vb_to_mvb(struct vb2_buffer *vb) +{ + return container_of(vb, struct mcam_vb_buffer, vb_buf); +} + +/* + * Hand a completed buffer back to user space. + */ +static void mcam_buffer_done(struct mcam_camera *cam, int frame, + struct vb2_buffer *vbuf) +{ + vbuf->v4l2_buf.bytesused = cam->pix_format.sizeimage; + vbuf->v4l2_buf.sequence = cam->buf_seq[frame]; + vb2_set_plane_payload(vbuf, 0, cam->pix_format.sizeimage); + vb2_buffer_done(vbuf, VB2_BUF_STATE_DONE); +} + + + +/* + * Debugging and related. + */ +#define cam_err(cam, fmt, arg...) \ + dev_err((cam)->dev, fmt, ##arg); +#define cam_warn(cam, fmt, arg...) \ + dev_warn((cam)->dev, fmt, ##arg); +#define cam_dbg(cam, fmt, arg...) \ + dev_dbg((cam)->dev, fmt, ##arg); + + +/* + * Flag manipulation helpers + */ +static void mcam_reset_buffers(struct mcam_camera *cam) +{ + int i; + + cam->next_buf = -1; + for (i = 0; i < cam->nbufs; i++) + clear_bit(i, &cam->flags); +} + +static inline int mcam_needs_config(struct mcam_camera *cam) +{ + return test_bit(CF_CONFIG_NEEDED, &cam->flags); +} + +static void mcam_set_config_needed(struct mcam_camera *cam, int needed) +{ + if (needed) + set_bit(CF_CONFIG_NEEDED, &cam->flags); + else + clear_bit(CF_CONFIG_NEEDED, &cam->flags); +} + +/* ------------------------------------------------------------------- */ +/* + * Make the controller start grabbing images. Everything must + * be set up before doing this. + */ +static void mcam_ctlr_start(struct mcam_camera *cam) +{ + /* set_bit performs a read, so no other barrier should be + needed here */ + mcam_reg_set_bit(cam, REG_CTRL0, C0_ENABLE); +} + +static void mcam_ctlr_stop(struct mcam_camera *cam) +{ + mcam_reg_clear_bit(cam, REG_CTRL0, C0_ENABLE); +} + +/* ------------------------------------------------------------------- */ + +#ifdef MCAM_MODE_VMALLOC +/* + * Code specific to the vmalloc buffer mode. + */ + +/* + * Allocate in-kernel DMA buffers for vmalloc mode. + */ +static int mcam_alloc_dma_bufs(struct mcam_camera *cam, int loadtime) +{ + int i; + + mcam_set_config_needed(cam, 1); + if (loadtime) + cam->dma_buf_size = dma_buf_size; + else + cam->dma_buf_size = cam->pix_format.sizeimage; + if (n_dma_bufs > 3) + n_dma_bufs = 3; + + cam->nbufs = 0; + for (i = 0; i < n_dma_bufs; i++) { + cam->dma_bufs[i] = dma_alloc_coherent(cam->dev, + cam->dma_buf_size, cam->dma_handles + i, + GFP_KERNEL); + if (cam->dma_bufs[i] == NULL) { + cam_warn(cam, "Failed to allocate DMA buffer\n"); + break; + } + (cam->nbufs)++; + } + + switch (cam->nbufs) { + case 1: + dma_free_coherent(cam->dev, cam->dma_buf_size, + cam->dma_bufs[0], cam->dma_handles[0]); + cam->nbufs = 0; + case 0: + cam_err(cam, "Insufficient DMA buffers, cannot operate\n"); + return -ENOMEM; + + case 2: + if (n_dma_bufs > 2) + cam_warn(cam, "Will limp along with only 2 buffers\n"); + break; + } + return 0; +} + +static void mcam_free_dma_bufs(struct mcam_camera *cam) +{ + int i; + + for (i = 0; i < cam->nbufs; i++) { + dma_free_coherent(cam->dev, cam->dma_buf_size, + cam->dma_bufs[i], cam->dma_handles[i]); + cam->dma_bufs[i] = NULL; + } + cam->nbufs = 0; +} + + +/* + * Set up DMA buffers when operating in vmalloc mode + */ +static void mcam_ctlr_dma_vmalloc(struct mcam_camera *cam) +{ + /* + * Store the first two Y buffers (we aren't supporting + * planar formats for now, so no UV bufs). Then either + * set the third if it exists, or tell the controller + * to just use two. + */ + mcam_reg_write(cam, REG_Y0BAR, cam->dma_handles[0]); + mcam_reg_write(cam, REG_Y1BAR, cam->dma_handles[1]); + if (cam->nbufs > 2) { + mcam_reg_write(cam, REG_Y2BAR, cam->dma_handles[2]); + mcam_reg_clear_bit(cam, REG_CTRL1, C1_TWOBUFS); + } else + mcam_reg_set_bit(cam, REG_CTRL1, C1_TWOBUFS); + if (cam->chip_id == V4L2_IDENT_CAFE) + mcam_reg_write(cam, REG_UBAR, 0); /* 32 bits only */ +} + +/* + * Copy data out to user space in the vmalloc case + */ +static void mcam_frame_tasklet(unsigned long data) +{ + struct mcam_camera *cam = (struct mcam_camera *) data; + int i; + unsigned long flags; + struct mcam_vb_buffer *buf; + + spin_lock_irqsave(&cam->dev_lock, flags); + for (i = 0; i < cam->nbufs; i++) { + int bufno = cam->next_buf; + + if (cam->state != S_STREAMING || bufno < 0) + break; /* I/O got stopped */ + if (++(cam->next_buf) >= cam->nbufs) + cam->next_buf = 0; + if (!test_bit(bufno, &cam->flags)) + continue; + if (list_empty(&cam->buffers)) { + cam->frame_state.singles++; + break; /* Leave it valid, hope for better later */ + } + cam->frame_state.delivered++; + clear_bit(bufno, &cam->flags); + buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, + queue); + list_del_init(&buf->queue); + /* + * Drop the lock during the big copy. This *should* be safe... + */ + spin_unlock_irqrestore(&cam->dev_lock, flags); + memcpy(vb2_plane_vaddr(&buf->vb_buf, 0), cam->dma_bufs[bufno], + cam->pix_format.sizeimage); + mcam_buffer_done(cam, bufno, &buf->vb_buf); + spin_lock_irqsave(&cam->dev_lock, flags); + } + spin_unlock_irqrestore(&cam->dev_lock, flags); +} + + +/* + * Make sure our allocated buffers are up to the task. + */ +static int mcam_check_dma_buffers(struct mcam_camera *cam) +{ + if (cam->nbufs > 0 && cam->dma_buf_size < cam->pix_format.sizeimage) + mcam_free_dma_bufs(cam); + if (cam->nbufs == 0) + return mcam_alloc_dma_bufs(cam, 0); + return 0; +} + +static void mcam_vmalloc_done(struct mcam_camera *cam, int frame) +{ + tasklet_schedule(&cam->s_tasklet); +} + +#else /* MCAM_MODE_VMALLOC */ + +static inline int mcam_alloc_dma_bufs(struct mcam_camera *cam, int loadtime) +{ + return 0; +} + +static inline void mcam_free_dma_bufs(struct mcam_camera *cam) +{ + return; +} + +static inline int mcam_check_dma_buffers(struct mcam_camera *cam) +{ + return 0; +} + + + +#endif /* MCAM_MODE_VMALLOC */ + + +#ifdef MCAM_MODE_DMA_CONTIG +/* ---------------------------------------------------------------------- */ +/* + * DMA-contiguous code. + */ +/* + * Set up a contiguous buffer for the given frame. Here also is where + * the underrun strategy is set: if there is no buffer available, reuse + * the buffer from the other BAR and set the CF_SINGLE_BUFFER flag to + * keep the interrupt handler from giving that buffer back to user + * space. In this way, we always have a buffer to DMA to and don't + * have to try to play games stopping and restarting the controller. + */ +static void mcam_set_contig_buffer(struct mcam_camera *cam, int frame) +{ + struct mcam_vb_buffer *buf; + /* + * If there are no available buffers, go into single mode + */ + if (list_empty(&cam->buffers)) { + buf = cam->vb_bufs[frame ^ 0x1]; + cam->vb_bufs[frame] = buf; + mcam_reg_write(cam, frame == 0 ? REG_Y0BAR : REG_Y1BAR, + vb2_dma_contig_plane_dma_addr(&buf->vb_buf, 0)); + set_bit(CF_SINGLE_BUFFER, &cam->flags); + cam->frame_state.singles++; + return; + } + /* + * OK, we have a buffer we can use. + */ + buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue); + list_del_init(&buf->queue); + mcam_reg_write(cam, frame == 0 ? REG_Y0BAR : REG_Y1BAR, + vb2_dma_contig_plane_dma_addr(&buf->vb_buf, 0)); + cam->vb_bufs[frame] = buf; + clear_bit(CF_SINGLE_BUFFER, &cam->flags); +} + +/* + * Initial B_DMA_contig setup. + */ +static void mcam_ctlr_dma_contig(struct mcam_camera *cam) +{ + mcam_reg_set_bit(cam, REG_CTRL1, C1_TWOBUFS); + cam->nbufs = 2; + mcam_set_contig_buffer(cam, 0); + mcam_set_contig_buffer(cam, 1); +} + +/* + * Frame completion handling. + */ +static void mcam_dma_contig_done(struct mcam_camera *cam, int frame) +{ + struct mcam_vb_buffer *buf = cam->vb_bufs[frame]; + + if (!test_bit(CF_SINGLE_BUFFER, &cam->flags)) { + cam->frame_state.delivered++; + mcam_buffer_done(cam, frame, &buf->vb_buf); + } + mcam_set_contig_buffer(cam, frame); +} + +#endif /* MCAM_MODE_DMA_CONTIG */ + +#ifdef MCAM_MODE_DMA_SG +/* ---------------------------------------------------------------------- */ +/* + * Scatter/gather-specific code. + */ + +/* + * Set up the next buffer for S/G I/O; caller should be sure that + * the controller is stopped and a buffer is available. + */ +static void mcam_sg_next_buffer(struct mcam_camera *cam) +{ + struct mcam_vb_buffer *buf; + + buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue); + list_del_init(&buf->queue); + /* + * Very Bad Not Good Things happen if you don't clear + * C1_DESC_ENA before making any descriptor changes. + */ + mcam_reg_clear_bit(cam, REG_CTRL1, C1_DESC_ENA); + mcam_reg_write(cam, REG_DMA_DESC_Y, buf->dma_desc_pa); + mcam_reg_write(cam, REG_DESC_LEN_Y, + buf->dma_desc_nent*sizeof(struct mcam_dma_desc)); + mcam_reg_write(cam, REG_DESC_LEN_U, 0); + mcam_reg_write(cam, REG_DESC_LEN_V, 0); + mcam_reg_set_bit(cam, REG_CTRL1, C1_DESC_ENA); + cam->vb_bufs[0] = buf; +} + +/* + * Initial B_DMA_sg setup + */ +static void mcam_ctlr_dma_sg(struct mcam_camera *cam) +{ + /* + * The list-empty condition can hit us at resume time + * if the buffer list was empty when the system was suspended. + */ + if (list_empty(&cam->buffers)) { + set_bit(CF_SG_RESTART, &cam->flags); + return; + } + + mcam_reg_clear_bit(cam, REG_CTRL1, C1_DESC_3WORD); + mcam_sg_next_buffer(cam); + cam->nbufs = 3; +} + + +/* + * Frame completion with S/G is trickier. We can't muck with + * a descriptor chain on the fly, since the controller buffers it + * internally. So we have to actually stop and restart; Marvell + * says this is the way to do it. + * + * Of course, stopping is easier said than done; experience shows + * that the controller can start a frame *after* C0_ENABLE has been + * cleared. So when running in S/G mode, the controller is "stopped" + * on receipt of the start-of-frame interrupt. That means we can + * safely change the DMA descriptor array here and restart things + * (assuming there's another buffer waiting to go). + */ +static void mcam_dma_sg_done(struct mcam_camera *cam, int frame) +{ + struct mcam_vb_buffer *buf = cam->vb_bufs[0]; + + /* + * If we're no longer supposed to be streaming, don't do anything. + */ + if (cam->state != S_STREAMING) + return; + /* + * If we have another buffer available, put it in and + * restart the engine. + */ + if (!list_empty(&cam->buffers)) { + mcam_sg_next_buffer(cam); + mcam_ctlr_start(cam); + /* + * Otherwise set CF_SG_RESTART and the controller will + * be restarted once another buffer shows up. + */ + } else { + set_bit(CF_SG_RESTART, &cam->flags); + cam->frame_state.singles++; + cam->vb_bufs[0] = NULL; + } + /* + * Now we can give the completed frame back to user space. + */ + cam->frame_state.delivered++; + mcam_buffer_done(cam, frame, &buf->vb_buf); +} + + +/* + * Scatter/gather mode requires stopping the controller between + * frames so we can put in a new DMA descriptor array. If no new + * buffer exists at frame completion, the controller is left stopped; + * this function is charged with gettig things going again. + */ +static void mcam_sg_restart(struct mcam_camera *cam) +{ + mcam_ctlr_dma_sg(cam); + mcam_ctlr_start(cam); + clear_bit(CF_SG_RESTART, &cam->flags); +} + +#else /* MCAM_MODE_DMA_SG */ + +static inline void mcam_sg_restart(struct mcam_camera *cam) +{ + return; +} + +#endif /* MCAM_MODE_DMA_SG */ + +/* ---------------------------------------------------------------------- */ +/* + * Buffer-mode-independent controller code. + */ + +/* + * Image format setup + */ +static void mcam_ctlr_image(struct mcam_camera *cam) +{ + int imgsz; + struct v4l2_pix_format *fmt = &cam->pix_format; + + imgsz = ((fmt->height << IMGSZ_V_SHIFT) & IMGSZ_V_MASK) | + (fmt->bytesperline & IMGSZ_H_MASK); + mcam_reg_write(cam, REG_IMGSIZE, imgsz); + mcam_reg_write(cam, REG_IMGOFFSET, 0); + /* YPITCH just drops the last two bits */ + mcam_reg_write_mask(cam, REG_IMGPITCH, fmt->bytesperline, + IMGP_YP_MASK); + /* + * Tell the controller about the image format we are using. + */ + switch (cam->pix_format.pixelformat) { + case V4L2_PIX_FMT_YUYV: + mcam_reg_write_mask(cam, REG_CTRL0, + C0_DF_YUV|C0_YUV_PACKED|C0_YUVE_YUYV, + C0_DF_MASK); + break; + + case V4L2_PIX_FMT_RGB444: + mcam_reg_write_mask(cam, REG_CTRL0, + C0_DF_RGB|C0_RGBF_444|C0_RGB4_XRGB, + C0_DF_MASK); + /* Alpha value? */ + break; + + case V4L2_PIX_FMT_RGB565: + mcam_reg_write_mask(cam, REG_CTRL0, + C0_DF_RGB|C0_RGBF_565|C0_RGB5_BGGR, + C0_DF_MASK); + break; + + default: + cam_err(cam, "Unknown format %x\n", cam->pix_format.pixelformat); + break; + } + /* + * Make sure it knows we want to use hsync/vsync. + */ + mcam_reg_write_mask(cam, REG_CTRL0, C0_SIF_HVSYNC, + C0_SIFM_MASK); +} + + +/* + * Configure the controller for operation; caller holds the + * device mutex. + */ +static int mcam_ctlr_configure(struct mcam_camera *cam) +{ + unsigned long flags; + + spin_lock_irqsave(&cam->dev_lock, flags); + clear_bit(CF_SG_RESTART, &cam->flags); + cam->dma_setup(cam); + mcam_ctlr_image(cam); + mcam_set_config_needed(cam, 0); + spin_unlock_irqrestore(&cam->dev_lock, flags); + return 0; +} + +static void mcam_ctlr_irq_enable(struct mcam_camera *cam) +{ + /* + * Clear any pending interrupts, since we do not + * expect to have I/O active prior to enabling. + */ + mcam_reg_write(cam, REG_IRQSTAT, FRAMEIRQS); + mcam_reg_set_bit(cam, REG_IRQMASK, FRAMEIRQS); +} + +static void mcam_ctlr_irq_disable(struct mcam_camera *cam) +{ + mcam_reg_clear_bit(cam, REG_IRQMASK, FRAMEIRQS); +} + + + +static void mcam_ctlr_init(struct mcam_camera *cam) +{ + unsigned long flags; + + spin_lock_irqsave(&cam->dev_lock, flags); + /* + * Make sure it's not powered down. + */ + mcam_reg_clear_bit(cam, REG_CTRL1, C1_PWRDWN); + /* + * Turn off the enable bit. It sure should be off anyway, + * but it's good to be sure. + */ + mcam_reg_clear_bit(cam, REG_CTRL0, C0_ENABLE); + /* + * Clock the sensor appropriately. Controller clock should + * be 48MHz, sensor "typical" value is half that. + */ + mcam_reg_write_mask(cam, REG_CLKCTRL, 2, CLK_DIV_MASK); + spin_unlock_irqrestore(&cam->dev_lock, flags); +} + + +/* + * Stop the controller, and don't return until we're really sure that no + * further DMA is going on. + */ +static void mcam_ctlr_stop_dma(struct mcam_camera *cam) +{ + unsigned long flags; + + /* + * Theory: stop the camera controller (whether it is operating + * or not). Delay briefly just in case we race with the SOF + * interrupt, then wait until no DMA is active. + */ + spin_lock_irqsave(&cam->dev_lock, flags); + clear_bit(CF_SG_RESTART, &cam->flags); + mcam_ctlr_stop(cam); + cam->state = S_IDLE; + spin_unlock_irqrestore(&cam->dev_lock, flags); + /* + * This is a brutally long sleep, but experience shows that + * it can take the controller a while to get the message that + * it needs to stop grabbing frames. In particular, we can + * sometimes (on mmp) get a frame at the end WITHOUT the + * start-of-frame indication. + */ + msleep(150); + if (test_bit(CF_DMA_ACTIVE, &cam->flags)) + cam_err(cam, "Timeout waiting for DMA to end\n"); + /* This would be bad news - what now? */ + spin_lock_irqsave(&cam->dev_lock, flags); + mcam_ctlr_irq_disable(cam); + spin_unlock_irqrestore(&cam->dev_lock, flags); +} + +/* + * Power up and down. + */ +static void mcam_ctlr_power_up(struct mcam_camera *cam) +{ + unsigned long flags; + + spin_lock_irqsave(&cam->dev_lock, flags); + cam->plat_power_up(cam); + mcam_reg_clear_bit(cam, REG_CTRL1, C1_PWRDWN); + spin_unlock_irqrestore(&cam->dev_lock, flags); + msleep(5); /* Just to be sure */ +} + +static void mcam_ctlr_power_down(struct mcam_camera *cam) +{ + unsigned long flags; + + spin_lock_irqsave(&cam->dev_lock, flags); + /* + * School of hard knocks department: be sure we do any register + * twiddling on the controller *before* calling the platform + * power down routine. + */ + mcam_reg_set_bit(cam, REG_CTRL1, C1_PWRDWN); + cam->plat_power_down(cam); + spin_unlock_irqrestore(&cam->dev_lock, flags); +} + +/* -------------------------------------------------------------------- */ +/* + * Communications with the sensor. + */ + +static int __mcam_cam_reset(struct mcam_camera *cam) +{ + return sensor_call(cam, core, reset, 0); +} + +/* + * We have found the sensor on the i2c. Let's try to have a + * conversation. + */ +static int mcam_cam_init(struct mcam_camera *cam) +{ + struct v4l2_dbg_chip_ident chip; + int ret; + + mutex_lock(&cam->s_mutex); + if (cam->state != S_NOTREADY) + cam_warn(cam, "Cam init with device in funky state %d", + cam->state); + ret = __mcam_cam_reset(cam); + if (ret) + goto out; + chip.ident = V4L2_IDENT_NONE; + chip.match.type = V4L2_CHIP_MATCH_I2C_ADDR; + chip.match.addr = cam->sensor_addr; + ret = sensor_call(cam, core, g_chip_ident, &chip); + if (ret) + goto out; + cam->sensor_type = chip.ident; + if (cam->sensor_type != V4L2_IDENT_OV7670) { + cam_err(cam, "Unsupported sensor type 0x%x", cam->sensor_type); + ret = -EINVAL; + goto out; + } +/* Get/set parameters? */ + ret = 0; + cam->state = S_IDLE; +out: + mcam_ctlr_power_down(cam); + mutex_unlock(&cam->s_mutex); + return ret; +} + +/* + * Configure the sensor to match the parameters we have. Caller should + * hold s_mutex + */ +static int mcam_cam_set_flip(struct mcam_camera *cam) +{ + struct v4l2_control ctrl; + + memset(&ctrl, 0, sizeof(ctrl)); + ctrl.id = V4L2_CID_VFLIP; + ctrl.value = flip; + return sensor_call(cam, core, s_ctrl, &ctrl); +} + + +static int mcam_cam_configure(struct mcam_camera *cam) +{ + struct v4l2_mbus_framefmt mbus_fmt; + int ret; + + v4l2_fill_mbus_format(&mbus_fmt, &cam->pix_format, cam->mbus_code); + ret = sensor_call(cam, core, init, 0); + if (ret == 0) + ret = sensor_call(cam, video, s_mbus_fmt, &mbus_fmt); + /* + * OV7670 does weird things if flip is set *before* format... + */ + ret += mcam_cam_set_flip(cam); + return ret; +} + +/* + * Get everything ready, and start grabbing frames. + */ +static int mcam_read_setup(struct mcam_camera *cam) +{ + int ret; + unsigned long flags; + + /* + * Configuration. If we still don't have DMA buffers, + * make one last, desperate attempt. + */ + if (cam->buffer_mode == B_vmalloc && cam->nbufs == 0 && + mcam_alloc_dma_bufs(cam, 0)) + return -ENOMEM; + + if (mcam_needs_config(cam)) { + mcam_cam_configure(cam); + ret = mcam_ctlr_configure(cam); + if (ret) + return ret; + } + + /* + * Turn it loose. + */ + spin_lock_irqsave(&cam->dev_lock, flags); + clear_bit(CF_DMA_ACTIVE, &cam->flags); + mcam_reset_buffers(cam); + mcam_ctlr_irq_enable(cam); + cam->state = S_STREAMING; + if (!test_bit(CF_SG_RESTART, &cam->flags)) + mcam_ctlr_start(cam); + spin_unlock_irqrestore(&cam->dev_lock, flags); + return 0; +} + +/* ----------------------------------------------------------------------- */ +/* + * Videobuf2 interface code. + */ + +static int mcam_vb_queue_setup(struct vb2_queue *vq, + const struct v4l2_format *fmt, unsigned int *nbufs, + unsigned int *num_planes, unsigned int sizes[], + void *alloc_ctxs[]) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vq); + int minbufs = (cam->buffer_mode == B_DMA_contig) ? 3 : 2; + + sizes[0] = cam->pix_format.sizeimage; + *num_planes = 1; /* Someday we have to support planar formats... */ + if (*nbufs < minbufs) + *nbufs = minbufs; + if (cam->buffer_mode == B_DMA_contig) + alloc_ctxs[0] = cam->vb_alloc_ctx; + return 0; +} + + +static void mcam_vb_buf_queue(struct vb2_buffer *vb) +{ + struct mcam_vb_buffer *mvb = vb_to_mvb(vb); + struct mcam_camera *cam = vb2_get_drv_priv(vb->vb2_queue); + unsigned long flags; + int start; + + spin_lock_irqsave(&cam->dev_lock, flags); + start = (cam->state == S_BUFWAIT) && !list_empty(&cam->buffers); + list_add(&mvb->queue, &cam->buffers); + if (cam->state == S_STREAMING && test_bit(CF_SG_RESTART, &cam->flags)) + mcam_sg_restart(cam); + spin_unlock_irqrestore(&cam->dev_lock, flags); + if (start) + mcam_read_setup(cam); +} + + +/* + * vb2 uses these to release the mutex when waiting in dqbuf. I'm + * not actually sure we need to do this (I'm not sure that vb2_dqbuf() needs + * to be called with the mutex held), but better safe than sorry. + */ +static void mcam_vb_wait_prepare(struct vb2_queue *vq) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vq); + + mutex_unlock(&cam->s_mutex); +} + +static void mcam_vb_wait_finish(struct vb2_queue *vq) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vq); + + mutex_lock(&cam->s_mutex); +} + +/* + * These need to be called with the mutex held from vb2 + */ +static int mcam_vb_start_streaming(struct vb2_queue *vq, unsigned int count) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vq); + + if (cam->state != S_IDLE) { + INIT_LIST_HEAD(&cam->buffers); + return -EINVAL; + } + cam->sequence = 0; + /* + * Videobuf2 sneakily hoards all the buffers and won't + * give them to us until *after* streaming starts. But + * we can't actually start streaming until we have a + * destination. So go into a wait state and hope they + * give us buffers soon. + */ + if (cam->buffer_mode != B_vmalloc && list_empty(&cam->buffers)) { + cam->state = S_BUFWAIT; + return 0; + } + return mcam_read_setup(cam); +} + +static int mcam_vb_stop_streaming(struct vb2_queue *vq) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vq); + unsigned long flags; + + if (cam->state == S_BUFWAIT) { + /* They never gave us buffers */ + cam->state = S_IDLE; + return 0; + } + if (cam->state != S_STREAMING) + return -EINVAL; + mcam_ctlr_stop_dma(cam); + /* + * VB2 reclaims the buffers, so we need to forget + * about them. + */ + spin_lock_irqsave(&cam->dev_lock, flags); + INIT_LIST_HEAD(&cam->buffers); + spin_unlock_irqrestore(&cam->dev_lock, flags); + return 0; +} + + +static const struct vb2_ops mcam_vb2_ops = { + .queue_setup = mcam_vb_queue_setup, + .buf_queue = mcam_vb_buf_queue, + .start_streaming = mcam_vb_start_streaming, + .stop_streaming = mcam_vb_stop_streaming, + .wait_prepare = mcam_vb_wait_prepare, + .wait_finish = mcam_vb_wait_finish, +}; + + +#ifdef MCAM_MODE_DMA_SG +/* + * Scatter/gather mode uses all of the above functions plus a + * few extras to deal with DMA mapping. + */ +static int mcam_vb_sg_buf_init(struct vb2_buffer *vb) +{ + struct mcam_vb_buffer *mvb = vb_to_mvb(vb); + struct mcam_camera *cam = vb2_get_drv_priv(vb->vb2_queue); + int ndesc = cam->pix_format.sizeimage/PAGE_SIZE + 1; + + mvb->dma_desc = dma_alloc_coherent(cam->dev, + ndesc * sizeof(struct mcam_dma_desc), + &mvb->dma_desc_pa, GFP_KERNEL); + if (mvb->dma_desc == NULL) { + cam_err(cam, "Unable to get DMA descriptor array\n"); + return -ENOMEM; + } + return 0; +} + +static int mcam_vb_sg_buf_prepare(struct vb2_buffer *vb) +{ + struct mcam_vb_buffer *mvb = vb_to_mvb(vb); + struct mcam_camera *cam = vb2_get_drv_priv(vb->vb2_queue); + struct vb2_dma_sg_desc *sgd = vb2_dma_sg_plane_desc(vb, 0); + struct mcam_dma_desc *desc = mvb->dma_desc; + struct scatterlist *sg; + int i; + + mvb->dma_desc_nent = dma_map_sg(cam->dev, sgd->sglist, sgd->num_pages, + DMA_FROM_DEVICE); + if (mvb->dma_desc_nent <= 0) + return -EIO; /* Not sure what's right here */ + for_each_sg(sgd->sglist, sg, mvb->dma_desc_nent, i) { + desc->dma_addr = sg_dma_address(sg); + desc->segment_len = sg_dma_len(sg); + desc++; + } + return 0; +} + +static int mcam_vb_sg_buf_finish(struct vb2_buffer *vb) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vb->vb2_queue); + struct vb2_dma_sg_desc *sgd = vb2_dma_sg_plane_desc(vb, 0); + + dma_unmap_sg(cam->dev, sgd->sglist, sgd->num_pages, DMA_FROM_DEVICE); + return 0; +} + +static void mcam_vb_sg_buf_cleanup(struct vb2_buffer *vb) +{ + struct mcam_camera *cam = vb2_get_drv_priv(vb->vb2_queue); + struct mcam_vb_buffer *mvb = vb_to_mvb(vb); + int ndesc = cam->pix_format.sizeimage/PAGE_SIZE + 1; + + dma_free_coherent(cam->dev, ndesc * sizeof(struct mcam_dma_desc), + mvb->dma_desc, mvb->dma_desc_pa); +} + + +static const struct vb2_ops mcam_vb2_sg_ops = { + .queue_setup = mcam_vb_queue_setup, + .buf_init = mcam_vb_sg_buf_init, + .buf_prepare = mcam_vb_sg_buf_prepare, + .buf_queue = mcam_vb_buf_queue, + .buf_finish = mcam_vb_sg_buf_finish, + .buf_cleanup = mcam_vb_sg_buf_cleanup, + .start_streaming = mcam_vb_start_streaming, + .stop_streaming = mcam_vb_stop_streaming, + .wait_prepare = mcam_vb_wait_prepare, + .wait_finish = mcam_vb_wait_finish, +}; + +#endif /* MCAM_MODE_DMA_SG */ + +static int mcam_setup_vb2(struct mcam_camera *cam) +{ + struct vb2_queue *vq = &cam->vb_queue; + + memset(vq, 0, sizeof(*vq)); + vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; + vq->drv_priv = cam; + INIT_LIST_HEAD(&cam->buffers); + switch (cam->buffer_mode) { + case B_DMA_contig: +#ifdef MCAM_MODE_DMA_CONTIG + vq->ops = &mcam_vb2_ops; + vq->mem_ops = &vb2_dma_contig_memops; + cam->vb_alloc_ctx = vb2_dma_contig_init_ctx(cam->dev); + vq->io_modes = VB2_MMAP | VB2_USERPTR; + cam->dma_setup = mcam_ctlr_dma_contig; + cam->frame_complete = mcam_dma_contig_done; +#endif + break; + case B_DMA_sg: +#ifdef MCAM_MODE_DMA_SG + vq->ops = &mcam_vb2_sg_ops; + vq->mem_ops = &vb2_dma_sg_memops; + vq->io_modes = VB2_MMAP | VB2_USERPTR; + cam->dma_setup = mcam_ctlr_dma_sg; + cam->frame_complete = mcam_dma_sg_done; +#endif + break; + case B_vmalloc: +#ifdef MCAM_MODE_VMALLOC + tasklet_init(&cam->s_tasklet, mcam_frame_tasklet, + (unsigned long) cam); + vq->ops = &mcam_vb2_ops; + vq->mem_ops = &vb2_vmalloc_memops; + vq->buf_struct_size = sizeof(struct mcam_vb_buffer); + vq->io_modes = VB2_MMAP; + cam->dma_setup = mcam_ctlr_dma_vmalloc; + cam->frame_complete = mcam_vmalloc_done; +#endif + break; + } + return vb2_queue_init(vq); +} + +static void mcam_cleanup_vb2(struct mcam_camera *cam) +{ + vb2_queue_release(&cam->vb_queue); +#ifdef MCAM_MODE_DMA_CONTIG + if (cam->buffer_mode == B_DMA_contig) + vb2_dma_contig_cleanup_ctx(cam->vb_alloc_ctx); +#endif +} + + +/* ---------------------------------------------------------------------- */ +/* + * The long list of V4L2 ioctl() operations. + */ + +static int mcam_vidioc_streamon(struct file *filp, void *priv, + enum v4l2_buf_type type) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_streamon(&cam->vb_queue, type); + mutex_unlock(&cam->s_mutex); + return ret; +} + + +static int mcam_vidioc_streamoff(struct file *filp, void *priv, + enum v4l2_buf_type type) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_streamoff(&cam->vb_queue, type); + mutex_unlock(&cam->s_mutex); + return ret; +} + + +static int mcam_vidioc_reqbufs(struct file *filp, void *priv, + struct v4l2_requestbuffers *req) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_reqbufs(&cam->vb_queue, req); + mutex_unlock(&cam->s_mutex); + return ret; +} + + +static int mcam_vidioc_querybuf(struct file *filp, void *priv, + struct v4l2_buffer *buf) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_querybuf(&cam->vb_queue, buf); + mutex_unlock(&cam->s_mutex); + return ret; +} + +static int mcam_vidioc_qbuf(struct file *filp, void *priv, + struct v4l2_buffer *buf) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_qbuf(&cam->vb_queue, buf); + mutex_unlock(&cam->s_mutex); + return ret; +} + +static int mcam_vidioc_dqbuf(struct file *filp, void *priv, + struct v4l2_buffer *buf) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_dqbuf(&cam->vb_queue, buf, filp->f_flags & O_NONBLOCK); + mutex_unlock(&cam->s_mutex); + return ret; +} + +static int mcam_vidioc_querycap(struct file *file, void *priv, + struct v4l2_capability *cap) +{ + strcpy(cap->driver, "marvell_ccic"); + strcpy(cap->card, "marvell_ccic"); + cap->version = 1; + cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | + V4L2_CAP_READWRITE | V4L2_CAP_STREAMING; + return 0; +} + + +static int mcam_vidioc_enum_fmt_vid_cap(struct file *filp, + void *priv, struct v4l2_fmtdesc *fmt) +{ + if (fmt->index >= N_MCAM_FMTS) + return -EINVAL; + strlcpy(fmt->description, mcam_formats[fmt->index].desc, + sizeof(fmt->description)); + fmt->pixelformat = mcam_formats[fmt->index].pixelformat; + return 0; +} + +static int mcam_vidioc_try_fmt_vid_cap(struct file *filp, void *priv, + struct v4l2_format *fmt) +{ + struct mcam_camera *cam = priv; + struct mcam_format_struct *f; + struct v4l2_pix_format *pix = &fmt->fmt.pix; + struct v4l2_mbus_framefmt mbus_fmt; + int ret; + + f = mcam_find_format(pix->pixelformat); + pix->pixelformat = f->pixelformat; + v4l2_fill_mbus_format(&mbus_fmt, pix, f->mbus_code); + mutex_lock(&cam->s_mutex); + ret = sensor_call(cam, video, try_mbus_fmt, &mbus_fmt); + mutex_unlock(&cam->s_mutex); + v4l2_fill_pix_format(pix, &mbus_fmt); + pix->bytesperline = pix->width * f->bpp; + pix->sizeimage = pix->height * pix->bytesperline; + return ret; +} + +static int mcam_vidioc_s_fmt_vid_cap(struct file *filp, void *priv, + struct v4l2_format *fmt) +{ + struct mcam_camera *cam = priv; + struct mcam_format_struct *f; + int ret; + + /* + * Can't do anything if the device is not idle + * Also can't if there are streaming buffers in place. + */ + if (cam->state != S_IDLE || cam->vb_queue.num_buffers > 0) + return -EBUSY; + + f = mcam_find_format(fmt->fmt.pix.pixelformat); + + /* + * See if the formatting works in principle. + */ + ret = mcam_vidioc_try_fmt_vid_cap(filp, priv, fmt); + if (ret) + return ret; + /* + * Now we start to change things for real, so let's do it + * under lock. + */ + mutex_lock(&cam->s_mutex); + cam->pix_format = fmt->fmt.pix; + cam->mbus_code = f->mbus_code; + + /* + * Make sure we have appropriate DMA buffers. + */ + if (cam->buffer_mode == B_vmalloc) { + ret = mcam_check_dma_buffers(cam); + if (ret) + goto out; + } + mcam_set_config_needed(cam, 1); +out: + mutex_unlock(&cam->s_mutex); + return ret; +} + +/* + * Return our stored notion of how the camera is/should be configured. + * The V4l2 spec wants us to be smarter, and actually get this from + * the camera (and not mess with it at open time). Someday. + */ +static int mcam_vidioc_g_fmt_vid_cap(struct file *filp, void *priv, + struct v4l2_format *f) +{ + struct mcam_camera *cam = priv; + + f->fmt.pix = cam->pix_format; + return 0; +} + +/* + * We only have one input - the sensor - so minimize the nonsense here. + */ +static int mcam_vidioc_enum_input(struct file *filp, void *priv, + struct v4l2_input *input) +{ + if (input->index != 0) + return -EINVAL; + + input->type = V4L2_INPUT_TYPE_CAMERA; + input->std = V4L2_STD_ALL; /* Not sure what should go here */ + strcpy(input->name, "Camera"); + return 0; +} + +static int mcam_vidioc_g_input(struct file *filp, void *priv, unsigned int *i) +{ + *i = 0; + return 0; +} + +static int mcam_vidioc_s_input(struct file *filp, void *priv, unsigned int i) +{ + if (i != 0) + return -EINVAL; + return 0; +} + +/* from vivi.c */ +static int mcam_vidioc_s_std(struct file *filp, void *priv, v4l2_std_id a) +{ + return 0; +} + +/* + * G/S_PARM. Most of this is done by the sensor, but we are + * the level which controls the number of read buffers. + */ +static int mcam_vidioc_g_parm(struct file *filp, void *priv, + struct v4l2_streamparm *parms) +{ + struct mcam_camera *cam = priv; + int ret; + + mutex_lock(&cam->s_mutex); + ret = sensor_call(cam, video, g_parm, parms); + mutex_unlock(&cam->s_mutex); + parms->parm.capture.readbuffers = n_dma_bufs; + return ret; +} + +static int mcam_vidioc_s_parm(struct file *filp, void *priv, + struct v4l2_streamparm *parms) +{ + struct mcam_camera *cam = priv; + int ret; + + mutex_lock(&cam->s_mutex); + ret = sensor_call(cam, video, s_parm, parms); + mutex_unlock(&cam->s_mutex); + parms->parm.capture.readbuffers = n_dma_bufs; + return ret; +} + +static int mcam_vidioc_g_chip_ident(struct file *file, void *priv, + struct v4l2_dbg_chip_ident *chip) +{ + struct mcam_camera *cam = priv; + + chip->ident = V4L2_IDENT_NONE; + chip->revision = 0; + if (v4l2_chip_match_host(&chip->match)) { + chip->ident = cam->chip_id; + return 0; + } + return sensor_call(cam, core, g_chip_ident, chip); +} + +static int mcam_vidioc_enum_framesizes(struct file *filp, void *priv, + struct v4l2_frmsizeenum *sizes) +{ + struct mcam_camera *cam = priv; + int ret; + + mutex_lock(&cam->s_mutex); + ret = sensor_call(cam, video, enum_framesizes, sizes); + mutex_unlock(&cam->s_mutex); + return ret; +} + +static int mcam_vidioc_enum_frameintervals(struct file *filp, void *priv, + struct v4l2_frmivalenum *interval) +{ + struct mcam_camera *cam = priv; + int ret; + + mutex_lock(&cam->s_mutex); + ret = sensor_call(cam, video, enum_frameintervals, interval); + mutex_unlock(&cam->s_mutex); + return ret; +} + +#ifdef CPTCFG_VIDEO_ADV_DEBUG +static int mcam_vidioc_g_register(struct file *file, void *priv, + struct v4l2_dbg_register *reg) +{ + struct mcam_camera *cam = priv; + + if (v4l2_chip_match_host(®->match)) { + reg->val = mcam_reg_read(cam, reg->reg); + reg->size = 4; + return 0; + } + return sensor_call(cam, core, g_register, reg); +} + +static int mcam_vidioc_s_register(struct file *file, void *priv, + const struct v4l2_dbg_register *reg) +{ + struct mcam_camera *cam = priv; + + if (v4l2_chip_match_host(®->match)) { + mcam_reg_write(cam, reg->reg, reg->val); + return 0; + } + return sensor_call(cam, core, s_register, reg); +} +#endif + +static const struct v4l2_ioctl_ops mcam_v4l_ioctl_ops = { + .vidioc_querycap = mcam_vidioc_querycap, + .vidioc_enum_fmt_vid_cap = mcam_vidioc_enum_fmt_vid_cap, + .vidioc_try_fmt_vid_cap = mcam_vidioc_try_fmt_vid_cap, + .vidioc_s_fmt_vid_cap = mcam_vidioc_s_fmt_vid_cap, + .vidioc_g_fmt_vid_cap = mcam_vidioc_g_fmt_vid_cap, + .vidioc_enum_input = mcam_vidioc_enum_input, + .vidioc_g_input = mcam_vidioc_g_input, + .vidioc_s_input = mcam_vidioc_s_input, + .vidioc_s_std = mcam_vidioc_s_std, + .vidioc_reqbufs = mcam_vidioc_reqbufs, + .vidioc_querybuf = mcam_vidioc_querybuf, + .vidioc_qbuf = mcam_vidioc_qbuf, + .vidioc_dqbuf = mcam_vidioc_dqbuf, + .vidioc_streamon = mcam_vidioc_streamon, + .vidioc_streamoff = mcam_vidioc_streamoff, + .vidioc_g_parm = mcam_vidioc_g_parm, + .vidioc_s_parm = mcam_vidioc_s_parm, + .vidioc_enum_framesizes = mcam_vidioc_enum_framesizes, + .vidioc_enum_frameintervals = mcam_vidioc_enum_frameintervals, + .vidioc_g_chip_ident = mcam_vidioc_g_chip_ident, +#ifdef CPTCFG_VIDEO_ADV_DEBUG + .vidioc_g_register = mcam_vidioc_g_register, + .vidioc_s_register = mcam_vidioc_s_register, +#endif +}; + +/* ---------------------------------------------------------------------- */ +/* + * Our various file operations. + */ +static int mcam_v4l_open(struct file *filp) +{ + struct mcam_camera *cam = video_drvdata(filp); + int ret = 0; + + filp->private_data = cam; + + cam->frame_state.frames = 0; + cam->frame_state.singles = 0; + cam->frame_state.delivered = 0; + mutex_lock(&cam->s_mutex); + if (cam->users == 0) { + ret = mcam_setup_vb2(cam); + if (ret) + goto out; + mcam_ctlr_power_up(cam); + __mcam_cam_reset(cam); + mcam_set_config_needed(cam, 1); + } + (cam->users)++; +out: + mutex_unlock(&cam->s_mutex); + return ret; +} + + +static int mcam_v4l_release(struct file *filp) +{ + struct mcam_camera *cam = filp->private_data; + + cam_dbg(cam, "Release, %d frames, %d singles, %d delivered\n", + cam->frame_state.frames, cam->frame_state.singles, + cam->frame_state.delivered); + mutex_lock(&cam->s_mutex); + (cam->users)--; + if (cam->users == 0) { + mcam_ctlr_stop_dma(cam); + mcam_cleanup_vb2(cam); + mcam_ctlr_power_down(cam); + if (cam->buffer_mode == B_vmalloc && alloc_bufs_at_read) + mcam_free_dma_bufs(cam); + } + mutex_unlock(&cam->s_mutex); + return 0; +} + +static ssize_t mcam_v4l_read(struct file *filp, + char __user *buffer, size_t len, loff_t *pos) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_read(&cam->vb_queue, buffer, len, pos, + filp->f_flags & O_NONBLOCK); + mutex_unlock(&cam->s_mutex); + return ret; +} + + + +static unsigned int mcam_v4l_poll(struct file *filp, + struct poll_table_struct *pt) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_poll(&cam->vb_queue, filp, pt); + mutex_unlock(&cam->s_mutex); + return ret; +} + + +static int mcam_v4l_mmap(struct file *filp, struct vm_area_struct *vma) +{ + struct mcam_camera *cam = filp->private_data; + int ret; + + mutex_lock(&cam->s_mutex); + ret = vb2_mmap(&cam->vb_queue, vma); + mutex_unlock(&cam->s_mutex); + return ret; +} + + + +static const struct v4l2_file_operations mcam_v4l_fops = { + .owner = THIS_MODULE, + .open = mcam_v4l_open, + .release = mcam_v4l_release, + .read = mcam_v4l_read, + .poll = mcam_v4l_poll, + .mmap = mcam_v4l_mmap, + .unlocked_ioctl = video_ioctl2, +}; + + +/* + * This template device holds all of those v4l2 methods; we + * clone it for specific real devices. + */ +static struct video_device mcam_v4l_template = { + .name = "mcam", + .tvnorms = V4L2_STD_NTSC_M, + .current_norm = V4L2_STD_NTSC_M, /* make mplayer happy */ + + .fops = &mcam_v4l_fops, + .ioctl_ops = &mcam_v4l_ioctl_ops, + .release = video_device_release_empty, +}; + +/* ---------------------------------------------------------------------- */ +/* + * Interrupt handler stuff + */ +static void mcam_frame_complete(struct mcam_camera *cam, int frame) +{ + /* + * Basic frame housekeeping. + */ + set_bit(frame, &cam->flags); + clear_bit(CF_DMA_ACTIVE, &cam->flags); + cam->next_buf = frame; + cam->buf_seq[frame] = ++(cam->sequence); + cam->frame_state.frames++; + /* + * "This should never happen" + */ + if (cam->state != S_STREAMING) + return; + /* + * Process the frame and set up the next one. + */ + cam->frame_complete(cam, frame); +} + + +/* + * The interrupt handler; this needs to be called from the + * platform irq handler with the lock held. + */ +int mccic_irq(struct mcam_camera *cam, unsigned int irqs) +{ + unsigned int frame, handled = 0; + + mcam_reg_write(cam, REG_IRQSTAT, FRAMEIRQS); /* Clear'em all */ + /* + * Handle any frame completions. There really should + * not be more than one of these, or we have fallen + * far behind. + * + * When running in S/G mode, the frame number lacks any + * real meaning - there's only one descriptor array - but + * the controller still picks a different one to signal + * each time. + */ + for (frame = 0; frame < cam->nbufs; frame++) + if (irqs & (IRQ_EOF0 << frame)) { + mcam_frame_complete(cam, frame); + handled = 1; + if (cam->buffer_mode == B_DMA_sg) + break; + } + /* + * If a frame starts, note that we have DMA active. This + * code assumes that we won't get multiple frame interrupts + * at once; may want to rethink that. + */ + if (irqs & (IRQ_SOF0 | IRQ_SOF1 | IRQ_SOF2)) { + set_bit(CF_DMA_ACTIVE, &cam->flags); + handled = 1; + if (cam->buffer_mode == B_DMA_sg) + mcam_ctlr_stop(cam); + } + return handled; +} + +/* ---------------------------------------------------------------------- */ +/* + * Registration and such. + */ +static struct ov7670_config sensor_cfg = { + /* + * Exclude QCIF mode, because it only captures a tiny portion + * of the sensor FOV + */ + .min_width = 320, + .min_height = 240, +}; + + +int mccic_register(struct mcam_camera *cam) +{ + struct i2c_board_info ov7670_info = { + .type = "ov7670", + .addr = 0x42 >> 1, + .platform_data = &sensor_cfg, + }; + int ret; + + /* + * Validate the requested buffer mode. + */ + if (buffer_mode >= 0) + cam->buffer_mode = buffer_mode; + if (cam->buffer_mode == B_DMA_sg && + cam->chip_id == V4L2_IDENT_CAFE) { + printk(KERN_ERR "marvell-cam: Cafe can't do S/G I/O, " + "attempting vmalloc mode instead\n"); + cam->buffer_mode = B_vmalloc; + } + if (!mcam_buffer_mode_supported(cam->buffer_mode)) { + printk(KERN_ERR "marvell-cam: buffer mode %d unsupported\n", + cam->buffer_mode); + return -EINVAL; + } + /* + * Register with V4L + */ + ret = v4l2_device_register(cam->dev, &cam->v4l2_dev); + if (ret) + return ret; + + mutex_init(&cam->s_mutex); + cam->state = S_NOTREADY; + mcam_set_config_needed(cam, 1); + cam->pix_format = mcam_def_pix_format; + cam->mbus_code = mcam_def_mbus_code; + INIT_LIST_HEAD(&cam->buffers); + mcam_ctlr_init(cam); + + /* + * Try to find the sensor. + */ + sensor_cfg.clock_speed = cam->clock_speed; + sensor_cfg.use_smbus = cam->use_smbus; + cam->sensor_addr = ov7670_info.addr; + cam->sensor = v4l2_i2c_new_subdev_board(&cam->v4l2_dev, + cam->i2c_adapter, &ov7670_info, NULL); + if (cam->sensor == NULL) { + ret = -ENODEV; + goto out_unregister; + } + + ret = mcam_cam_init(cam); + if (ret) + goto out_unregister; + /* + * Get the v4l2 setup done. + */ + ret = v4l2_ctrl_handler_init(&cam->ctrl_handler, 10); + if (ret) + goto out_unregister; + cam->v4l2_dev.ctrl_handler = &cam->ctrl_handler; + + mutex_lock(&cam->s_mutex); + cam->vdev = mcam_v4l_template; + cam->vdev.debug = 0; + cam->vdev.v4l2_dev = &cam->v4l2_dev; + video_set_drvdata(&cam->vdev, cam); + ret = video_register_device(&cam->vdev, VFL_TYPE_GRABBER, -1); + if (ret) + goto out; + + /* + * If so requested, try to get our DMA buffers now. + */ + if (cam->buffer_mode == B_vmalloc && !alloc_bufs_at_read) { + if (mcam_alloc_dma_bufs(cam, 1)) + cam_warn(cam, "Unable to alloc DMA buffers at load" + " will try again later."); + } + +out: + v4l2_ctrl_handler_free(&cam->ctrl_handler); + mutex_unlock(&cam->s_mutex); + return ret; +out_unregister: + v4l2_device_unregister(&cam->v4l2_dev); + return ret; +} + + +void mccic_shutdown(struct mcam_camera *cam) +{ + /* + * If we have no users (and we really, really should have no + * users) the device will already be powered down. Trying to + * take it down again will wedge the machine, which is frowned + * upon. + */ + if (cam->users > 0) { + cam_warn(cam, "Removing a device with users!\n"); + mcam_ctlr_power_down(cam); + } + vb2_queue_release(&cam->vb_queue); + if (cam->buffer_mode == B_vmalloc) + mcam_free_dma_bufs(cam); + video_unregister_device(&cam->vdev); + v4l2_ctrl_handler_free(&cam->ctrl_handler); + v4l2_device_unregister(&cam->v4l2_dev); +} + +/* + * Power management + */ +#ifdef CONFIG_PM + +void mccic_suspend(struct mcam_camera *cam) +{ + mutex_lock(&cam->s_mutex); + if (cam->users > 0) { + enum mcam_state cstate = cam->state; + + mcam_ctlr_stop_dma(cam); + mcam_ctlr_power_down(cam); + cam->state = cstate; + } + mutex_unlock(&cam->s_mutex); +} + +int mccic_resume(struct mcam_camera *cam) +{ + int ret = 0; + + mutex_lock(&cam->s_mutex); + if (cam->users > 0) { + mcam_ctlr_power_up(cam); + __mcam_cam_reset(cam); + } else { + mcam_ctlr_power_down(cam); + } + mutex_unlock(&cam->s_mutex); + + set_bit(CF_CONFIG_NEEDED, &cam->flags); + if (cam->state == S_STREAMING) { + /* + * If there was a buffer in the DMA engine at suspend + * time, put it back on the queue or we'll forget about it. + */ + if (cam->buffer_mode == B_DMA_sg && cam->vb_bufs[0]) + list_add(&cam->vb_bufs[0]->queue, &cam->buffers); + ret = mcam_read_setup(cam); + } + return ret; +} +#endif /* CONFIG_PM */ |