path: root/techlibs/machxo2/cells_sim.v

module LUT4 #(
	parameter [15:0] INIT = 0
) (
	input A, B, C, D,
	output Z
);
	// This form of LUT propagates as few x's as possible.
	wire [7:0] s3 = D ?     INIT[15:8] :     INIT[7:0];
	wire [3:0] s2 = C ?       s3[ 7:4] :       s3[3:0];
	wire [1:0] s1 = B ?       s2[ 3:2] :       s2[1:0];
	assign Z =      A ?          s1[1] :         s1[0];
endmodule

module FACADE_FF #(
	parameter GSR = "ENABLED",
	parameter CEMUX = "1",
	parameter CLKMUX = "0",
	parameter LSRMUX = "LSR",
	parameter LSRONMUX = "LSRMUX",
	parameter SRMODE = "LSR_OVER_CE",
	parameter REGSET = "SET",
	parameter REGMODE = "FF"
) (
	input CLK, DI, LSR, CE,
	output reg Q
);

	wire muxce;
	generate
		case (CEMUX)
			"1": assign muxce = 1'b1;
			"0": assign muxce = 1'b0;
			"INV": assign muxce = ~CE;
			default: assign muxce = CE;
		endcase
	endgenerate

	wire muxlsr = (LSRMUX == "INV") ? ~LSR : LSR;
	wire muxlsron = (LSRONMUX == "LSRMUX") ? muxlsr : 1'b0;
	wire muxclk = (CLKMUX == "INV") ? ~CLK : CLK;
	wire srval = (REGSET == "SET") ? 1'b1 : 1'b0;

	initial Q = srval;

	generate
		if (REGMODE == "FF") begin
			if (SRMODE == "ASYNC") begin
				always @(posedge muxclk, posedge muxlsron)
					if (muxlsron)
						Q <= srval;
					else if (muxce)
						Q <= DI;
			end else begin
				always @(posedge muxclk)
					if (muxlsron)
						Q <= srval;
					else if (muxce)
						Q <= DI;
			end
		end else if (REGMODE == "LATCH") begin
			ERROR_UNSUPPORTED_FF_MODE error();
		end else begin
			ERROR_UNKNOWN_FF_MODE error();
		end
	endgenerate
endmodule

/* For consistency with ECP5; represents F0/F1 => OFX0 mux in a slice. */
module PFUMX (input ALUT, BLUT, C0, output Z);
	assign Z = C0 ? ALUT : BLUT;
endmodule

/* For consistency with ECP5; represents FXA/FXB => OFX1 mux in a slice. */
module L6MUX21 (input D0, D1, SD, output Z);
	assign Z = SD ? D1 : D0;
endmodule

/* For consistency, input order matches TRELLIS_SLICE even though the BELs in
prjtrellis were filled in clockwise order from bottom left. */
module FACADE_SLICE #(
	parameter MODE = "LOGIC",
	parameter GSR = "ENABLED",
	parameter SRMODE = "LSR_OVER_CE",
	parameter CEMUX = "1",
	parameter CLKMUX = "0",
	parameter LSRMUX = "LSR",
	parameter LSRONMUX = "LSRMUX",
	parameter LUT0_INITVAL = 16'hFFFF,
	parameter LUT1_INITVAL = 16'hFFFF,
	parameter REGMODE = "FF",
	parameter REG0_SD = "1",
	parameter REG1_SD = "1",
	parameter REG0_REGSET = "SET",
	parameter REG1_REGSET = "SET",
	parameter CCU2_INJECT1_0 = "YES",
	parameter CCU2_INJECT1_1 = "YES",
	parameter WREMUX = "INV"
) (
	input A0, B0, C0, D0,
	input A1, B1, C1, D1,
	input M0, M1,
	input FCI, FXA, FXB,

	input CLK, LSR, CE,
	input DI0, DI1,

	input WD0, WD1,
	input WAD0, WAD1, WAD2, WAD3,
	input WRE, WCK,

	output F0, Q0,
	output F1, Q1,
	output FCO, OFX0, OFX1,

	output WDO0, WDO1, WDO2, WDO3,
	output WADO0, WADO1, WADO2, WADO3
);

	generate
		if (MODE == "LOGIC") begin
			L6MUX21 FXMUX (.D0(FXA), .D1(FXB), .SD(M1), .Z(OFX1));

			wire k0;
			wire k1;
			PFUMX K0K1MUX (.ALUT(k1), .BLUT(k0), .C0(M0), .Z(OFX0));

			LUT4 #(.INIT(LUT0_INITVAL)) LUT_0 (.A(A0), .B(B0), .C(C0), .D(D0), .Z(k0));
			LUT4 #(.INIT(LUT1_INITVAL)) LUT_1 (.A(A0), .B(B0), .C(C0), .D(D0), .Z(k1));

			assign F0 = k0;
			assign F1 = k1;
		end else if (MODE == "CCU2") begin
			ERROR_UNSUPPORTED_SLICE_MODE error();
		end else if (MODE == "DPRAM") begin
			ERROR_UNSUPPORTED_SLICE_MODE error();
		end else begin
			ERROR_UNKNOWN_SLICE_MODE error();
		end
	endgenerate

	/* Reg can be fed either by M, or DI inputs; DI inputs muxes OFX and F
	outputs (in other words, feeds back into FACADE_SLICE). */
	wire di0 = (REG0_SD == "1") ? DI0 : M0;
	wire di1 = (REG1_SD == "1") ? DI1 : M1;

	FACADE_FF#(.GSR(GSR), .CEMUX(CEMUX), .CLKMUX(CLKMUX), .LSRMUX(LSRMUX),
		.LSRONMUX(LSRONMUX), .SRMODE(SRMODE), .REGSET(REG0_REGSET),
		.REGMODE(REGMODE)) REG_0 (.CLK(CLK), .DI(di0), .LSR(LSR), .CE(CE), .Q(Q0));
	FACADE_FF#(.GSR(GSR), .CEMUX(CEMUX), .CLKMUX(CLKMUX), .LSRMUX(LSRMUX),
		.LSRONMUX(LSRONMUX), .SRMODE(SRMODE), .REGSET(REG1_REGSET),
		.REGMODE(REGMODE)) REG_1 (.CLK(CLK), .DI(di1), .LSR(LSR), .CE(CE), .Q(Q1));
endmodule

module FACADE_IO #(
	parameter DIR = "INPUT"
) (
	inout PAD,
	input I, T,
	output O
);
	generate
		if (DIR == "INPUT") begin
			assign O = PAD;
		end else if (DIR == "OUTPUT") begin
			assign PAD = T ? 1'bz : I;
		end else if (DIR == "BIDIR") begin
			assign PAD = T ? 1'bz : I;
			assign O = PAD;
		end else begin
			ERROR_UNKNOWN_IO_MODE error();
		end
	endgenerate
endmodule

(* blackbox *)
module OSCH #(
	parameter NOM_FREQ = "2.08"
) (
	input STDBY,
	output OSC,
	output SEDSTDBY
);
endmodule

(* blackbox *)
module DCCA (
	input CLKI,
	input CE,
	output CLKO
);
endmodule

(* blackbox *)
module DCMA (
	input CLK0,
	input CLK1,
	input SEL,
	output DCMOUT
);
endmodule

(* abc9_box, lib_whitebox *)
module DPR16X4C (
		input [3:0] DI,
		input WCK, WRE,
		input [3:0] RAD,
		input [3:0] WAD,
		output [3:0] DO
);
	parameter INITVAL = "0x0000000000000000";

	function [63:0] convert_initval;
		input [143:0] hex_initval;
		reg done;
		reg [63:0] temp;
		reg [7:0] char;
		integer i;
		begin
			done = 1'b0;
			temp = 0;
			for (i = 0; i < 16; i = i + 1) begin
				if (!done) begin
					char = hex_initval[8*i +: 8];
					if (char == "x") begin
						done = 1'b1;
					end else begin
						if (char >= "0" && char <= "9")
							temp[4*i +: 4] = char - "0";
						else if (char >= "A" && char <= "F")
							temp[4*i +: 4] = 10 + char - "A";
						else if (char >= "a" && char <= "f")
							temp[4*i +: 4] = 10 + char - "a";
					end
				end
			end
			convert_initval = temp;
		end
	endfunction

	localparam conv_initval = convert_initval(INITVAL);

	reg [3:0] ram[0:15];
	integer i;
	initial begin
		for (i = 0; i < 15; i = i + 1) begin
			ram[i] <= conv_initval[4*i +: 4];
		end
	end

	always @(posedge WCK)
		if (WRE)
			ram[WAD] <= DI;

	assign DO = ram[RAD];
endmodule

(* blackbox *)
module DP8KC(
  input DIA8, DIA7, DIA6, DIA5, DIA4, DIA3, DIA2, DIA1, DIA0,
  input ADA12, ADA11, ADA10, ADA9, ADA8, ADA7, ADA6, ADA5, ADA4, ADA3, ADA2, ADA1, ADA0,
  input CEA, OCEA, CLKA, WEA, RSTA,
  input CSA2, CSA1, CSA0,
  output DOA8, DOA7, DOA6, DOA5, DOA4, DOA3, DOA2, DOA1, DOA0,

  input DIB8, DIB7, DIB6, DIB5, DIB4, DIB3, DIB2, DIB1, DIB0,
  input ADB12, ADB11, ADB10, ADB9, ADB8, ADB7, ADB6, ADB5, ADB4, ADB3, ADB2, ADB1, ADB0,
  input CEB, OCEB, CLKB, WEB, RSTB,
  input CSB2, CSB1, CSB0,
  output DOB8, DOB7, DOB6, DOB5, DOB4, DOB3, DOB2, DOB1, DOB0
);
	parameter DATA_WIDTH_A = 9;
	parameter DATA_WIDTH_B = 9;

	parameter REGMODE_A = "NOREG";
	parameter REGMODE_B = "NOREG";

	parameter RESETMODE = "SYNC";
	parameter ASYNC_RESET_RELEASE = "SYNC";

	parameter CSDECODE_A = "0b000";
	parameter CSDECODE_B = "0b000";

	parameter WRITEMODE_A = "NORMAL";
	parameter WRITEMODE_B = "NORMAL";

	parameter GSR = "ENABLED";
	parameter INIT_DATA = "STATIC";

	parameter INITVAL_00 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_01 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_02 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_03 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_04 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_05 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_06 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_07 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_08 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_09 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0A = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0B = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0C = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0D = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0E = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_0F = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_10 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_11 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_12 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_13 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_14 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_15 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_16 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_17 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_18 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_19 = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1A = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1B = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1C = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1D = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1E = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
	parameter INITVAL_1F = "0x00000000000000000000000000000000000000000000000000000000000000000000000000000000";
endmodule

// IO- "$__" cells for the iopadmap pass. These are temporary cells not meant
// to be instantiated by the end user. They are required in this file for
// attrmvcp to work.
(* blackbox *)
module  \$__FACADE_OUTPAD (input I, output O); endmodule
(* blackbox *)
module  \$__FACADE_INPAD (input I, output O); endmodule
(* blackbox *)
module  \$__FACADE_TOUTPAD (input I, T, output O); endmodule
(* blackbox *)
module  \$__FACADE_TINOUTPAD (input I, T, output O, inout B); endmodule