diff options
Diffstat (limited to 'examples/custom-class/firmware/main.c')
| -rw-r--r-- | examples/custom-class/firmware/main.c | 91 |
1 files changed, 91 insertions, 0 deletions
diff --git a/examples/custom-class/firmware/main.c b/examples/custom-class/firmware/main.c new file mode 100644 index 0000000..2d93db9 --- /dev/null +++ b/examples/custom-class/firmware/main.c @@ -0,0 +1,91 @@ +/* Name: main.c + * Project: custom-class, a basic USB example + * Author: Christian Starkjohann + * Creation Date: 2008-04-09 + * Tabsize: 4 + * Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt) + * This Revision: $Id$ + */ + +/* +This example should run on most AVRs with only little changes. No special +hardware resources except INT0 are used. You may have to change usbconfig.h for +different I/O pins for USB. Please note that USB D+ must be the INT0 pin, or +at least be connected to INT0 as well. +We assume that an LED is connected to port B bit 0. If you connect it to a +different port or bit, change the macros below: +*/ +#define LED_PORT_DDR DDRB +#define LED_PORT_OUTPUT PORTB +#define LED_BIT 0 + +#include <avr/io.h> +#include <avr/wdt.h> +#include <avr/interrupt.h> /* for sei() */ +#include <util/delay.h> /* for _delay_ms() */ + +#include <avr/pgmspace.h> /* required by usbdrv.h */ +#include "usbdrv.h" +#include "oddebug.h" /* This is also an example for using debug macros */ +#include "requests.h" /* The custom request numbers we use */ + +/* ------------------------------------------------------------------------- */ +/* ----------------------------- USB interface ----------------------------- */ +/* ------------------------------------------------------------------------- */ + +uchar usbFunctionSetup(uchar data[8]) +{ +usbRequest_t *rq = (void *)data; + + if(rq->bRequest == CUSTOM_RQ_SET_STATUS){ + if(rq->wValue.bytes[0] & 1){ /* set LED */ + LED_PORT_OUTPUT |= _BV(LED_BIT); + }else{ /* clear LED */ + LED_PORT_OUTPUT &= ~_BV(LED_BIT); + } + }else if(rq->bRequest == CUSTOM_RQ_GET_STATUS){ + static uchar dataBuffer[1]; /* buffer must stay valid when usbFunctionSetup returns */ + dataBuffer[0] = ((LED_PORT_OUTPUT & _BV(LED_BIT)) != 0); + usbMsgPtr = dataBuffer; /* tell the driver which data to return */ + return 1; /* tell the driver to send 1 byte */ + } + return 0; /* default for not implemented requests: return no data back to host */ +} + +/* ------------------------------------------------------------------------- */ + +int main(void) +{ +uchar i; + + wdt_enable(WDTO_1S); + /* Even if you don't use the watchdog, turn it off here. On newer devices, + * the status of the watchdog (on/off, period) is PRESERVED OVER RESET! + */ + DBG1(0x00, 0, 0); /* debug output: main starts */ + /* RESET status: all port bits are inputs without pull-up. + * That's the way we need D+ and D-. Therefore we don't need any + * additional hardware initialization. + */ + odDebugInit(); + usbInit(); + usbDeviceDisconnect(); /* enforce re-enumeration, do this while interrupts are disabled! */ + i = 0; + while(--i){ /* fake USB disconnect for > 250 ms */ + wdt_reset(); + _delay_ms(1); + } + usbDeviceConnect(); + LED_PORT_DDR |= _BV(LED_BIT); /* make the LED bit an output */ + sei(); + DBG1(0x01, 0, 0); /* debug output: main loop starts */ + for(;;){ /* main event loop */ + DBG1(0x02, 0, 0); /* debug output: main loop iterates */ + wdt_reset(); + usbPoll(); + } + return 0; +} + +/* ------------------------------------------------------------------------- */ |