1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/gdisp/SSD1306/board_SSD1306_spi.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
#define GDISP_BUS_MAX_TRANSFER_SIZE 64
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
#define SSD1306_RESET_PORT GPIOB
#define SSD1306_RESET_PIN 5
#define SSD1306_MISO_PORT GPIOB
#define SSD1306_MISO_PIN 8
#define SSD1306_MOSI_PORT GPIOB
#define SSD1306_MOSI_PIN 7
#define SSD1306_SCK_PORT GPIOB
#define SSD1306_SCK_PIN 6
#define SSD1306_CS_PORT GPIOB
#define SSD1306_CS_PIN 5
#define SET_RST palSetPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
#define CLR_RST palClearPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1config = {
NULL,
/* HW dependent part.*/
SSD1306_MISO_PORT,
SSD1306_MISO_PIN,
0
//SPI_CR1_BR_0
};
static inline void init_board(GDisplay *g) {
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
// RESET pin.
palSetPadMode(SSD1306_RESET_PORT, SSD1306_RESET_PIN, PAL_MODE_OUTPUT_PUSHPULL);
spiInit();
palSetPadMode(SSD1306_MISO_PORT, SSD1306_MISO_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_MOSI_PORT, SSD1306_MOSI_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_SCK_PORT, SSD1306_SCK_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPad(SSD1306_CS_PORT, SSD1306_CS_PIN);
palSetPadMode(SSD1306_CS_PORT, SSD1306_CS_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
break;
}
}
static inline void post_init_board(GDisplay *g) {
(void) g;
}
static inline void setpin_reset(GDisplay *g, bool_t state) {
(void) g;
if(state)
CLR_RST
else
SET_RST
}
static inline void acquire_bus(GDisplay *g) {
(void) g;
spiAcquireBus(&SPID1);
}
static inline void release_bus(GDisplay *g) {
(void) g;
spiReleaseBus(&SPID1);
}
static inline void write_cmd(GDisplay *g, uint8_t cmd) {
uint8_t command[2];
command[0] = 0x00; // Co = 0, D/C = 0
command[1] = cmd;
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, 2, command);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
static inline void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
uint8_t command[1];
(void) g;
command[0] = 0x40; // Co = 0, D/C = 1
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, 1, command);
spiStartSend(&SPID1, length, data);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
#endif /* _GDISP_LLD_BOARD_H */
|
