1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/gdisp/SSD1306/board_SSD1306_spi.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// The command byte to put on the front of each page line
#define SSD1306_PAGE_PREFIX 0x40 // Co = 0, D/C = 1
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
#define SSD1306_RESET_PORT GPIOB
#define SSD1306_RESET_PIN 5
#define SSD1306_MISO_PORT GPIOB
#define SSD1306_MISO_PIN 8
#define SSD1306_MOSI_PORT GPIOB
#define SSD1306_MOSI_PIN 7
#define SSD1306_SCK_PORT GPIOB
#define SSD1306_SCK_PIN 6
#define SSD1306_CS_PORT GPIOB
#define SSD1306_CS_PIN 5
#define SET_RST palSetPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
#define CLR_RST palClearPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1config = {
NULL,
/* HW dependent part.*/
SSD1306_MISO_PORT,
SSD1306_MISO_PIN,
0
//SPI_CR1_BR_0
};
#if GFX_USE_OS_CHIBIOS
static int32_t thdPriority = 0;
#endif
static inline void init_board(GDisplay *g) {
unsigned i;
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
// RESET pin.
palSetPadMode(SSD1306_RESET_PORT, SSD1306_RESET_PIN, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(SSD1306_MISO_PORT, SSD1306_MISO_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_MOSI_PORT, SSD1306_MOSI_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_SCK_PORT, SSD1306_SCK_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPad(SSD1306_CS_PORT, SSD1306_CS_PIN);
palSetPadMode(SSD1306_CS_PORT, SSD1306_CS_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
spiInit();
break;
}
}
static inline void post_init_board(GDisplay *g) {
(void) g;
}
static inline void setpin_reset(GDisplay *g, bool_t state) {
(void) g;
if(state)
CLR_RST
else
SET_RST
}
static inline void acquire_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
thdPriority = (int32_t)chThdGetPriority();
chThdSetPriority(HIGHPRIO);
#endif
spiAcquireBus(&SPID1);
}
static inline void release_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
chThdSetPriority(thdPriority);
#endif
spiReleaseBus(&SPID1);
}
static inline void write_cmd(GDisplay *g, uint8_t cmd) {
uint8_t command[2];
(void) g;
command[0] = 0x00; // Co = 0, D/C = 0
command[1] = cmd;
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, 2, command);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
static inline void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
(void) g;
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, length, data);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
#endif /* _GDISP_LLD_BOARD_H */
|
