1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file boards/addons/gdisp/board_SSD1306_i2c.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
*
* @note This file contains a mix of hardware specific and operating system specific
* code. You will need to change it for your CPU and/or operating system.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// The command byte to put on the front of each page line
#define SSD1306_PAGE_PREFIX 0x40 // Co = 0, D/C = 1
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
#define SSD1306_RESET_PORT GPIOB
#define SSD1306_RESET_PIN 5
/**
* The default slave address is 0x3D, (talking about
* only the real address part here) and the slave
* address can be changed to 0x3C by soldering the
* SA0 pads on the bottom side of the module.
*
* b7 | b6 | b5 | b4 | b3 | b2 | b1 | b0
* --------------------------------------
* 0 | 1 | 1 | 1 | 1 | 0 |SA0 | R/W
*/
#define SSD1306_I2C_ADDRESS 0x3D
#define SSD1306_SDA_PORT GPIOB
#define SSD1306_SDA_PIN 7
#define SSD1306_SCL_PORT GPIOB
#define SSD1306_SCL_PIN 6
#define SET_RST palSetPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
#define CLR_RST palClearPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
// I2C configuration structure.
static I2CConfig i2cconfig;
#if GFX_USE_OS_CHIBIOS
static int32_t thdPriority = 0;
#endif
static inline void init_board(GDisplay *g) {
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
// RESET pin.
palSetPadMode(SSD1306_RESET_PORT, SSD1306_RESET_PIN, PAL_MODE_OUTPUT_PUSHPULL);
/*
* Initializes the I2C driver 1. The I2C1 signals are routed as follows:
* PB6 - SCL.
* PB7 - SDA.
* Timing value comes from ST I2C config tool (xls):
* 0x00901D2B; // 100kHz Standard Mode
* 0x00300444; // 100kHz Fast Mode
* 0x0030020A; // 400kHz Fast Mode
* 0x00100002; // 800kHz Fast Mode +
*/
palSetPadMode(SSD1306_SCL_PORT, SSD1306_SCL_PIN, PAL_MODE_ALTERNATE(1));
palSetPadMode(SSD1306_SDA_PORT, SSD1306_SDA_PIN, PAL_MODE_ALTERNATE(1));
i2cconfig.timingr = 0x00100002; // 800kHz Fast Mode+
i2cInit();
break;
}
}
static inline void post_init_board(GDisplay *g) {
(void) g;
}
static inline void setpin_reset(GDisplay *g, bool_t state) {
(void) g;
if(state)
CLR_RST
else
SET_RST
}
static inline void acquire_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
thdPriority = (int32_t)chThdGetPriority();
chThdSetPriority(HIGHPRIO);
#endif
i2cAcquireBus(&I2CD1);
}
static inline void release_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
chThdSetPriority(thdPriority);
#endif
i2cReleaseBus(&I2CD1);
}
static inline void write_cmd(GDisplay *g, uint8_t cmd) {
uint8_t command[2];
(void) g;
command[0] = 0x00; // Co = 0, D/C = 0
command[1] = cmd;
i2cStart(&I2CD1, &i2cconfig);
i2cMasterTransmitTimeout(&I2CD1, SSD1306_I2C_ADDRESS, command, 2, 0, 0, MS2ST(10));
i2cStop(&I2CD1);
}
static inline void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
(void) g;
i2cStart(&I2CD1, &i2cconfig);
i2cMasterTransmitTimeout(&I2CD1, SSD1306_I2C_ADDRESS, data, length, 0, 0, MS2ST(10));
i2cStop(&I2CD1);
}
#endif /* _GDISP_LLD_BOARD_H */
|
