1 files changed, 0 insertions, 156 deletions
diff --git a/drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h b/drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h
deleted file mode 100644
index 7270cdaf..00000000
--- a/drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h
+++ /dev/null
@@ -1,156 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h
- * @brief   GDISP Graphics Driver subsystem low level driver source for
- * 			the ILI9481 and compatible HVGA display
- *
- * @addtogroup GDISP
- * @{
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-#define SET_CS		palSetPad(GPIOD, 12);
-#define CLR_CS		palClearPad(GPIOD, 12);
-#define SET_RS		palSetPad(GPIOD, 13);
-#define CLR_RS		palClearPad(GPIOD, 13);
-#define SET_WR		palSetPad(GPIOD, 14);
-#define CLR_WR		palClearPad(GPIOD, 14);
-#define SET_RD		palSetPad(GPIOD, 15);
-#define CLR_RD		palClearPad(GPIOD, 15);
-
-/**
- * @brief   Initialise the board for the display.
- * @notes	This board definition uses GPIO and assumes exclusive access to these GPIO pins
- *
- * @notapi
- */
-static inline void init_board(void) {
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-	palSetPadMode(GPIOD, 12, PAL_MODE_OUTPUT_PUSHPULL);
-	palSetPadMode(GPIOD, 13, PAL_MODE_OUTPUT_PUSHPULL);
-	palSetPadMode(GPIOD, 14, PAL_MODE_OUTPUT_PUSHPULL);
-	palSetPadMode(GPIOD, 15, PAL_MODE_OUTPUT_PUSHPULL);
-	
-	// Configure the pins to a well know state
-	SET_RS;
-	SET_RD;
-	SET_WR;
-	CLR_CS;
-}
-
-
-/**
- * @brief   Set or clear the lcd reset pin.
- *
- * @param[in] state		TRUE = lcd in reset, FALSE = normal operation
- * 
- * @notapi
- */
-static inline void setpin_reset(bool_t state) {
-	(void) state;
-	/* Nothing to do here - reset pin tied to Vcc */
-}
-
-/**
- * @brief   Set the lcd back-light level.
- *
- * @param[in] percent		0 to 100%
- * 
- * @notapi
- */
-static inline void set_backlight(uint8_t percent) {
-	(void) percent;
-	/* Nothing to do here - Backlight always on */
-}
-
-/**
- * @brief   Take exclusive control of the bus
- *
- * @notapi
- */
-static inline void acquire_bus(void) {
-	/* Nothing to do here since LCD is the only device on that bus */
-}
-
-/**
- * @brief   Release exclusive control of the bus
- *
- * @notapi
- */
-static inline void release_bus(void) {
-	/* Nothing to do here since LCD is the only device on that bus */
-}
-
-/**
- * @brief   Send data to the index register.
- *
- * @param[in] index		The index register to set
- *
- * @notapi
- */
-static inline void write_index(uint16_t index) {
-	palWritePort(GPIOE, index);
-	CLR_RS; CLR_WR; SET_WR; SET_RS;
-}
-
-/**
- * @brief   Send data to the lcd.
- *
- * @param[in] data		The data to send
- * 
- * @notapi
- */
-static inline void write_data(uint16_t data) {
-	palWritePort(GPIOE, data);
-	CLR_WR; SET_WR;
-}
-
-/**
- * @brief   Set the bus in read mode
- *
- * @notapi
- */
-static inline void setreadmode(void) {
-	// change pin mode to digital input
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_INPUT);
-}
-
-/**
- * @brief   Set the bus back into write mode
- *
- * @notapi
- */
-static inline void setwritemode(void) {
-	// change pin mode back to digital output
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-}
-
-/**
- * @brief   Read data from the lcd.
- *
- * @return	The data from the lcd
- * @note	The chip select may need to be asserted/de-asserted
- * 			around the actual spi read
- * 
- * @notapi
- */
-static inline uint16_t read_data(void) {
-	uint16_t	value;
-	
-	CLR_RD;
-	value = palReadPort(GPIOE);
-	SET_RD;
-	
-	return value;
-}
-
-#endif /* _GDISP_LLD_BOARD_H */
-/** @} */