diff options
Diffstat (limited to 'drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h')
| -rw-r--r-- | drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h | 152 |
1 files changed, 152 insertions, 0 deletions
diff --git a/drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h b/drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h new file mode 100644 index 00000000..7e9ce2b4 --- /dev/null +++ b/drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h @@ -0,0 +1,152 @@ +/* + * This file is subject to the terms of the GFX License, v1.0. If a copy of + * the license was not distributed with this file, you can obtain one at: + * + * http://chibios-gfx.com/license.html + */ + +/** + * @file drivers/gdisp/ILI9481/gdisp_lld_board_example_fsmc.h + * @brief GDISP Graphics Driver subsystem low level driver source for + * the ILI9481 and compatible HVGA display + * + * @addtogroup GDISP + * @{ + */ + +#ifndef _GDISP_LLD_BOARD_H +#define _GDISP_LLD_BOARD_H + +#define GDISP_REG ((volatile uint16_t *) 0x60000000)[0] /* RS = 0 */ +#define GDISP_RAM ((volatile uint16_t *) 0x60020000)[0] /* RS = 1 */ + +/** + * @brief Initialise the board for the display. + * @notes Performs the following functions: + * 1. initialise the io port used by your display + * 2. initialise the reset pin (initial state not-in-reset) + * 3. initialise the chip select pin (initial state not-active) + * 4. initialise the backlight pin (initial state back-light off) + * + * @notapi + */ +static inline void init_board(void) { + const unsigned char FSMC_Bank; + + #if defined(STM32F1XX) || defined(STM32F3XX) + /* FSMC setup for F1/F3 */ + rccEnableAHB(RCC_AHBENR_FSMCEN, 0); + + #if defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM) + #error "DMA not implemented for F1/F3 Devices" + #endif + #elif defined(STM32F4XX) || defined(STM32F2XX) + /* STM32F2-F4 FSMC init */ + rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0); + + #if defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM) + if (dmaStreamAllocate(GDISP_DMA_STREAM, 0, NULL, NULL)) chSysHalt(); + dmaStreamSetMemory0(GDISP_DMA_STREAM, &GDISP_RAM); + dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M); + #endif + #else + #error "FSMC not implemented for this device" + #endif + + /* set pins to FSMC mode */ + IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 7) | (1 << 8) | + (1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0}; + + IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) | + (1 << 13) | (1 << 14) | (1 << 15), 0}; + + palSetBusMode(&busD, PAL_MODE_ALTERNATE(12)); + palSetBusMode(&busE, PAL_MODE_ALTERNATE(12)); + + FSMC_Bank = 0; + + /* FSMC timing */ + FSMC_Bank1->BTCR[FSMC_Bank+1] = (FSMC_BTR1_ADDSET_1 | FSMC_BTR1_ADDSET_3) \ + | (FSMC_BTR1_DATAST_1 | FSMC_BTR1_DATAST_3) \ + | (FSMC_BTR1_BUSTURN_1 | FSMC_BTR1_BUSTURN_3) ; + + /* Bank1 NOR/SRAM control register configuration + * This is actually not needed as already set by default after reset */ + FSMC_Bank1->BTCR[FSMC_Bank] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN; +} + +/** + * @brief Set or clear the lcd reset pin. + * + * @param[in] state TRUE = lcd in reset, FALSE = normal operation + * + * @notapi + */ +static inline void setpin_reset(bool_t state) { + (void) state; + /* Nothing to do here */ +} + +/** + * @brief Set the lcd back-light level. + * + * @param[in] percent 0 to 100% + * + * @notapi + */ +static inline void set_backlight(uint8_t percent) { + (void) percent; + /* Nothing to do here */ +} + +/** + * @brief Take exclusive control of the bus + * + * @notapi + */ +static inline void acquire_bus(void) { + /* Nothing to do here */ +} + +/** + * @brief Release exclusive control of the bus + * + * @notapi + */ +static inline void release_bus(void) { + /* Nothing to do here */ +} + +/** + * @brief Send data to the index register. + * + * @param[in] index The index register to set + * + * @notapi + */ +static inline void write_index(uint16_t index) { GDISP_REG = index; } + +/** + * @brief Send data to the lcd. + * + * @param[in] data The data to send + * + * @notapi + */ +static inline void write_data(uint16_t data) { GDISP_RAM = data; } + +#if GDISP_HARDWARE_READPIXEL || GDISP_HARDWARE_SCROLL || defined(__DOXYGEN__) +/** + * @brief Read data from the lcd. + * + * @return The data from the lcd + * @note The chip select may need to be asserted/de-asserted + * around the actual spi read + * + * @notapi + */ +static inline uint16_t read_data(void) { return GDISP_RAM; } +#endif + +#endif /* _GDISP_LLD_BOARD_H */ +/** @} */ |