1 files changed, 0 insertions, 136 deletions
diff --git a/boards/addons/gdisp/board_SSD1306_spi.h b/boards/addons/gdisp/board_SSD1306_spi.h
deleted file mode 100644
index f7b1ac6d..00000000
--- a/boards/addons/gdisp/board_SSD1306_spi.h
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    boards/addons/gdisp/board_SSD1306_spi.h
- * @brief   GDISP Graphic Driver subsystem board interface for the SSD1306 display.
- *
- * @note	This file contains a mix of hardware specific and operating system specific
- *			code. You will need to change it for your CPU and/or operating system.
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// The command byte to put on the front of each page line
-#define SSD1306_PAGE_PREFIX		0x40			 		// Co = 0, D/C = 1
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-#define SSD1306_RESET_PORT		GPIOB
-#define SSD1306_RESET_PIN		5
-#define SSD1306_MISO_PORT		GPIOB
-#define SSD1306_MISO_PIN		8
-#define SSD1306_MOSI_PORT		GPIOB
-#define SSD1306_MOSI_PIN		7
-#define SSD1306_SCK_PORT		GPIOB
-#define SSD1306_SCK_PIN			6
-#define SSD1306_CS_PORT			GPIOB
-#define SSD1306_CS_PIN			5
-#define SET_RST					palSetPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
-#define CLR_RST					palClearPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
-
-/*
- * SPI1 configuration structure.
- * Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
- * The slave select line is the pin 4 on the port GPIOA.
- */
-static const SPIConfig spi1config = {
-	0,
-	/* HW dependent part.*/
-	SSD1306_MISO_PORT,
-	SSD1306_MISO_PIN,
-	0
-	//SPI_CR1_BR_0
-};
-
-#if GFX_USE_OS_CHIBIOS
-	static int32_t thdPriority = 0;
-#endif
-
-static GFXINLINE void init_board(GDisplay *g) {
-	unsigned	i;
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		// RESET pin.
-		palSetPadMode(SSD1306_RESET_PORT, SSD1306_RESET_PIN, PAL_MODE_OUTPUT_PUSHPULL);
-
-		palSetPadMode(SSD1306_MISO_PORT, SSD1306_MISO_PIN, 	PAL_MODE_ALTERNATE(1)|
-															PAL_STM32_OSPEED_HIGHEST);
-		palSetPadMode(SSD1306_MOSI_PORT, SSD1306_MOSI_PIN, 	PAL_MODE_ALTERNATE(1)|
-															PAL_STM32_OSPEED_HIGHEST);
-		palSetPadMode(SSD1306_SCK_PORT,  SSD1306_SCK_PIN,  	PAL_MODE_ALTERNATE(1)|
-															PAL_STM32_OSPEED_HIGHEST);
-		palSetPad(SSD1306_CS_PORT, SSD1306_CS_PIN);
-		palSetPadMode(SSD1306_CS_PORT,   SSD1306_CS_PIN,   	PAL_MODE_ALTERNATE(1)|
-															PAL_STM32_OSPEED_HIGHEST);
-		spiInit();
-		break;
-	}
-}
-
-static GFXINLINE void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static GFXINLINE void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	if(state)
-		CLR_RST
-	else
-		SET_RST
-}
-
-static GFXINLINE void acquire_bus(GDisplay *g) {
-	(void) g;
-	#if GFX_USE_OS_CHIBIOS
-		thdPriority = (int32_t)chThdGetPriority();
-		chThdSetPriority(HIGHPRIO);
-	#endif
-	spiAcquireBus(&SPID1);
-}
-
-static GFXINLINE void release_bus(GDisplay *g) {
-	(void) g;
-	#if GFX_USE_OS_CHIBIOS
-		chThdSetPriority(thdPriority);
-	#endif
-	spiReleaseBus(&SPID1);
-}
-
-static GFXINLINE void write_cmd(GDisplay *g, uint8_t cmd) {
-	uint8_t command[2];
-	(void)	g;
-
-	command[0] = 0x00;		// Co = 0, D/C = 0
-	command[1] = cmd;
-
-	spiStart(&SPID1, &spi1config);
-	spiSelect(&SPID1);
-	spiStartSend(&SPID1, 2, command);
-	spiUnselect(&SPID1);
-	spiStop(&SPID1);
-}
-
-static GFXINLINE void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
-	(void) g;
-
-	spiStart(&SPID1, &spi1config);
-	spiSelect(&SPID1);
-	spiStartSend(&SPID1, length, data);
-	spiUnselect(&SPID1);
-	spiStop(&SPID1);
-}
-
-
-#endif /* _GDISP_LLD_BOARD_H */
-