diff options
Diffstat (limited to 'boards/addons/gdisp/board_HX8347D_stm32f4discovery.h')
-rw-r--r-- | boards/addons/gdisp/board_HX8347D_stm32f4discovery.h | 160 |
1 files changed, 160 insertions, 0 deletions
diff --git a/boards/addons/gdisp/board_HX8347D_stm32f4discovery.h b/boards/addons/gdisp/board_HX8347D_stm32f4discovery.h new file mode 100644 index 00000000..df287477 --- /dev/null +++ b/boards/addons/gdisp/board_HX8347D_stm32f4discovery.h @@ -0,0 +1,160 @@ +/* + * This file is subject to the terms of the GFX License. If a copy of + * the license was not distributed with this file, you can obtain one at: + * + * http://ugfx.org/license.html + */ + +/** + * @file drivers/gdisp/HX8347D/board_HX8347D_stm32f4discovery.h + * @brief GDISP Graphic Driver subsystem board SPI interface for the HX8347D display. + */ + +#ifndef _GDISP_LLD_BOARD_H +#define _GDISP_LLD_BOARD_H + +// For a multiple display configuration we would put all this in a structure and then +// set g->board to that structure. + +/* Pin assignments */ +#define SET_RST palSetPad(GPIOB, 8) +#define CLR_RST palClearPad(GPIOB, 8) +#define SET_DATA palSetPad(GPIOB, 9) +#define CLR_DATA palClearPad(GPIOB, 9) +#define SET_CS palSetPad(GPIOA, 4) +#define CLR_CS palClearPad(GPIOA, 4) + +/* PWM configuration structure. We use timer 4 channel 2 (orange LED on board). */ +static const PWMConfig pwmcfg = { + 1000000, /* 1 MHz PWM clock frequency. */ + 100, /* PWM period is 100 cycles. */ + NULL, + { + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL} + }, + 0 +}; + +/* + * SPI1 configuration structure. + * Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first. + * The slave select line is the pin 4 on the port GPIOA. + */ +static const SPIConfig spi1cfg_8bit = { + NULL, + /* HW dependent part.*/ + GPIOA, + 4, + 0 //SPI_CR1_BR_0 +}; + +/* + * SPI1 configuration structure. + * Speed 42MHz, CPHA=0, CPOL=0, 16bits frames, MSb transmitted first. + * The slave select line is the pin 4 on the port GPIOA. + */ +static const SPIConfig spi1cfg_16bit = { + NULL, + /* HW dependent part.*/ + GPIOA, + 4, + SPI_CR1_DFF //SPI_CR1_BR_0 +}; + +static inline void init_board(GDisplay *g) { + + // As we are not using multiple displays we set g->board to NULL as we don't use it. + g->board = 0; + + switch(g->controllerdisplay) { + case 0: // Set up for Display 0 + /* Display backlight control */ + /* TIM4 is an alternate function 2 (AF2) */ + pwmStart(&PWMD4, &pwmcfg); + palSetPadMode(GPIOD, 13, PAL_MODE_ALTERNATE(2)); + pwmEnableChannel(&PWMD4, 1, 100); + + palSetPadMode(GPIOB, 8, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* RST */ + palSetPadMode(GPIOB, 9, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* RS */ + /* + * Initializes the SPI driver 1. The SPI1 signals are routed as follow: + * PB12 - NSS. + * PB13 - SCK. + * PB14 - MISO. + * PB15 - MOSI. + */ + SET_CS; SET_DATA; + spiStart(&SPID1, &spi1cfg_8bit); + palSetPadMode(GPIOA, 4, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* NSS. */ + palSetPadMode(GPIOA, 5, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST); /* SCK. */ + palSetPadMode(GPIOA, 6, PAL_MODE_ALTERNATE(5)); /* MISO. */ + palSetPadMode(GPIOA, 7, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST); /* MOSI. */ + break; + } +} + +static inline void post_init_board(GDisplay *g) { + (void) g; +} + +static inline void setpin_reset(GDisplay *g, bool_t state) { + (void) g; + if (state) { + CLR_RST; + } else { + SET_RST; + } +} + +static inline void set_backlight(GDisplay *g, uint8_t percent) { + (void) g; + pwmEnableChannel(&PWMD4, 1, percent); +} + +static inline void acquire_bus(GDisplay *g) { + (void) g; + spiAcquireBus(&SPID1); + while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0)); // Safety + CLR_CS; +} + +static inline void release_bus(GDisplay *g) { + (void) g; + SET_CS; + spiReleaseBus(&SPID1); +} + +static inline void busmode16(GDisplay *g) { + (void) g; + spiStart(&SPID1, &spi1cfg_16bit); +} + +static inline void busmode8(GDisplay *g) { + (void) g; + spiStart(&SPID1, &spi1cfg_8bit); +} + +static inline void write_index(GDisplay *g, uint8_t index) { + (void) g; + CLR_DATA; + SPI1->DR = index; + while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0)); + SET_DATA; +} + +static inline void write_data(GDisplay *g, uint8_t data) { + (void) g; + SPI1->DR = data; + while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0)); +} + +static inline void write_ram16(GDisplay *g, uint16_t data) { + (void) g; + SPI1->DR = data; + while((SPI1->SR & SPI_SR_TXE) == 0); +} + +#endif /* _GDISP_LLD_BOARD_H */ |