fixed Embest board

2 files changed, 0 insertions, 198 deletions

diff --git a/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h b/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h
deleted file mode 100644
index 99d37299..00000000
--- a/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h
+++ /dev/null
@@ -1,108 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/SSD1289/board_SSD1289_firebullstm32f103.h
- * @brief   GDISP Graphic Driver subsystem board interface for the SSD1289 display.
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-#define SET_CS		palSetPad(GPIOD, 12);
-#define CLR_CS		palClearPad(GPIOD, 12);
-#define SET_RS		palSetPad(GPIOD, 13);
-#define CLR_RS		palClearPad(GPIOD, 13);
-#define SET_WR		palSetPad(GPIOD, 14);
-#define CLR_WR		palClearPad(GPIOD, 14);
-#define SET_RD		palSetPad(GPIOD, 15);
-#define CLR_RD		palClearPad(GPIOD, 15);
-
-static inline void init_board(GDisplay *g) {
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 12, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 13, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 14, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 15, PAL_MODE_OUTPUT_PUSHPULL);
-
-		// Configure the pins to a well know state
-		SET_RS;
-		SET_RD;
-		SET_WR;
-		CLR_CS;
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	(void) state;
-	/* Nothing to do here - reset pin tied to Vcc */
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent) {
-	(void) g;
-	(void) percent;
-	/* Nothing to do here - Backlight always on */
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-	palWritePort(GPIOE, index);
-	CLR_RS; CLR_WR; SET_WR; SET_RS;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-	palWritePort(GPIOE, data);
-	CLR_WR; SET_WR;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-	// change pin mode to digital input
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_INPUT);
-	CLR_RD;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-	// change pin mode back to digital output
-	SET_RD;
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	return palReadPort(GPIOE);
-}
-
-#if defined(GDISP_USE_DMA)
-	#error "GDISP - SSD1289: The GPIO interface does not support DMA"
-#endif
-
-#endif /* _GDISP_LLD_BOARD_H */
-
diff --git a/boards/addons/ginput/touch/ADS7843/ginput_lld_mouse_board_firebull_stm32f103.h b/boards/addons/ginput/touch/ADS7843/ginput_lld_mouse_board_firebull_stm32f103.h
deleted file mode 100644
index 63e9e3dd..00000000
--- a/boards/addons/ginput/touch/ADS7843/ginput_lld_mouse_board_firebull_stm32f103.h
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/ginput/touch/ADS7843/ginput_lld_mouse_board_firebull_stm32f103.h
- * @brief   GINPUT ouch low level driver source for the ADS7843 on the FireBull STM32F103-FB board.
- *
- * @defgroup Mouse Mouse
- * @ingroup GINPUT
- * @{
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-static const SPIConfig spicfg = { 
-    NULL,
-	GPIOC, 
-    6,
-    /* SPI_CR1_BR_2 |*/ SPI_CR1_BR_1 | SPI_CR1_BR_0,
-};
-
-/**
- * @brief   Initialise the board for the touch.
- *
- * @notapi
- */
-static inline void init_board(void) {
-	spiStart(&SPID1, &spicfg);
-}
-
-/**
- * @brief   Check whether the surface is currently touched
- * @return	TRUE if the surface is currently touched
- *
- * @notapi
- */
-static inline bool_t getpin_pressed(void) {
-	return (!palReadPad(GPIOC, 4));
-}
-/**
- * @brief   Aquire the bus ready for readings
- *
- * @notapi
- */
-static inline void aquire_bus(void) {
-	spiAcquireBus(&SPID1);
-    //TOUCHSCREEN_SPI_PROLOGUE();
-    palClearPad(GPIOC, 6);
-}
-
-/**
- * @brief   Release the bus after readings
- *
- * @notapi
- */
-static inline void release_bus(void) {
-	palSetPad(GPIOC, 6);
-	spiReleaseBus(&SPID1);
-    //TOUCHSCREEN_SPI_EPILOGUE();
-}
-
-/**
- * @brief   Read a value from touch controller
- * @return	The value read from the controller
- *
- * params[in] port	The controller port to read.
- *
- * @notapi
- */
-static inline uint16_t read_value(uint16_t port) {
-    static uint8_t txbuf[3] = {0};
-    static uint8_t rxbuf[3] = {0};
-    uint16_t ret;
-
-    txbuf[0] = port;
-
-    spiExchange(&SPID1, 3, txbuf, rxbuf);
-
-    ret = (rxbuf[1] << 5) | (rxbuf[2] >> 3); 
-    
-	return ret;
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-/** @} */