added Marlin board

2 files changed, 0 insertions, 224 deletions

diff --git a/boards/addons/gdisp/board_RA8875_marlin.h b/boards/addons/gdisp/board_RA8875_marlin.h
deleted file mode 100644
index b1d55a92..00000000
--- a/boards/addons/gdisp/board_RA8875_marlin.h
+++ /dev/null
@@ -1,113 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/RA8875/board_RA8875_marlin.h
- * @brief   GDISP Graphic Driver subsystem board interface for the RA8875 display.
- */
-
-#ifndef _BOARD_RA8875_H
-#define _BOARD_RA8875_H
-
-// For a multiple display configuration we would put all this in a structure and then
-// set g->board to that structure.
-#define GDISP_RAM              (*((volatile uint16_t *) 0x68000000)) /* RS = 0 */
-#define GDISP_REG              (*((volatile uint16_t *) 0x68020000)) /* RS = 1 */
-#define FSMC_BANK				4
-
-
-static inline void init_board(GDisplay *g) {
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-		// setup for display 0
-		case 0: {		
-
-			// enable the FSMC peripheral
-			rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
-
-			// setup the pin modes for FSMC
-			IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 8) |
-									(1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0};
-
-			IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
-								(1 << 13) | (1 << 14) | (1 << 15), 0};
-
-			IOBus busG = {GPIOG, (1 << 10), 0};
-
-			palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
-			palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
-			palSetBusMode(&busG, PAL_MODE_ALTERNATE(12));
-
-			// FSMC timing
-			FSMC_Bank1->BTCR[FSMC_BANK+1] = (FSMC_BTR1_ADDSET_1 | FSMC_BTR1_ADDSET_3) \
-					| (FSMC_BTR1_DATAST_1 | FSMC_BTR1_DATAST_3) \
-					| (FSMC_BTR1_BUSTURN_1 | FSMC_BTR1_BUSTURN_3) ;
-
-			// Bank1 NOR/SRAM control register configuration
-			// This is actually not needed as already set by default after reset
-			FSMC_Bank1->BTCR[FSMC_BANK] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
-
-			break;
-		}
-
-		// marlin does not have any secondary display so far
-		default:
-			break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-	
-	// FSMC delay reduced as the controller now runs at full speed
-	FSMC_Bank1->BTCR[2+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
-	FSMC_Bank1->BTCR[2] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	(void) state;
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-
-	GDISP_REG = index;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-
-	GDISP_RAM = data;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	(void) g;
-
-	return GDISP_RAM;
-}
-
-#endif /* _BOARD_RA8875_H */
-
diff --git a/boards/addons/ginput/touch/FT5x06/ginput_lld_mouse_board_marlin.h b/boards/addons/ginput/touch/FT5x06/ginput_lld_mouse_board_marlin.h
deleted file mode 100644
index e3e18c24..00000000
--- a/boards/addons/ginput/touch/FT5x06/ginput_lld_mouse_board_marlin.h
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/ginput/touch/FT5x06/ginput_lld_mouse_board_marlin.h
- * @brief   GINPUT Touch low level driver source for the FT5x06.
- *
- * @defgroup Mouse Mouse
- * @ingroup GINPUT
- * @{
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-/* I2C interface #2 - Touchscreen controller */
-static const I2CConfig i2ccfg2 = {
-    OPMODE_I2C,
-    400000,
-    FAST_DUTY_CYCLE_2,
-};
-
-/**
- * @brief   Initialise the board for the touch.
- *
- * @notapi
- */
-static void init_board(void) {
-
-}
-
-
-/**
- * @brief	Write a value into a certain register
- *
- * @param[in] reg	The register address
- * @param[in] n		The amount of bytes (one or two)
- * @param[in] val	The value
- *
- * @notapi
- */
-static void write_reg(uint8_t reg, uint8_t n, uint16_t val) {
-	uint8_t txbuf[3];
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-
-	if (n == 1) {
-		txbuf[1] = val;
-		i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 2, NULL, 0, MS2ST(FT5x06_TIMEOUT));
-	} else if (n == 2) {
-		txbuf[1] = ((val & 0xFF00) >> 8);
-		txbuf[2] = (val & 0x00FF);
-		i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 3, NULL, 0, MS2ST(FT5x06_TIMEOUT));
-	}
-	
-	i2cReleaseBus(&I2CD2);
-}
- 
-/**
- * @brief	Read the value of a certain register
- *
- * @param[in] reg	The register address
- * @param[in] n		The amount of bytes (one or two)
- *
- * @return Data read from device (one byte or two depending on n param)
- *
- * @notapi
- */
-static uint16_t read_reg(uint8_t reg, uint8_t n) {
-	uint8_t txbuf[1], rxbuf[2];
-	uint16_t ret;
-
-	rxbuf[0] = 0;
-	rxbuf[1] = 0;
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 1, rxbuf, n, MS2ST(FT5x06_TIMEOUT));
-
-	if (n == 1) {
-		ret = rxbuf[0];
-	} else if (n == 2) {
-		ret = ((rxbuf[0] << 8) | (rxbuf[1] & 0xFF));
-	}
-
-	i2cReleaseBus(&I2CD2);
-
-	return ret;
-}
-
-static void read_reg_n(uint8_t reg, uint8_t n, uint8_t *rxbuf) {
-	uint8_t txbuf[1];
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 1, rxbuf, n, MS2ST(FT5x06_TIMEOUT));
-
-	i2cReleaseBus(&I2CD2);
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-/** @} */
-