1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage OB's Quad-Relay outlet control using a Teensy2++
*
* \section Sec_Compat Project Compatibility:
*
* The following list indicates what microcontrollers are compatible with this project.
*
* \li AT90USB1286
*
* \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this project.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>None</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>None</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USB Standards</td>
* </tr>
* <tr>
* <td><b>Supported USB Speeds:</b></td>
* <td>Low Speed Mode, Full Speed Mode</td>
* </tr>
* </table>
*
* \section Sec_Description Project Description:
*
* Firmware for a Teensy2++ AVR-based miniboard to control four relays, using the
* same protocol used by the commercially available Silver Shield PM power outlets
* ( http://sourceforge.net/projects/sispmctl ) sold for some time. Because this
* project mimics the original device, it can be controlled using the "sismpctl"
* package included in many Linux distributions - including router-orientated
* versions such as OpenWRT - to control the board's relays.
*
* Relays 1 to 4 are respectively wired to pins C4, C5, C6 and C7 of the Teensy++ V2,
* which are the PORTC bits 4 to 7 of the AT90USB1286. The relays MUST be wired through
* a transistor, and a diode must be added in antiparallel on the relay's coil pins to
* protect the transistor from back EMF generated from the relay when the coil is turned off.
* The transistor base pin is wired to the Teensy data port through a 10K resistor. A
* LED may be also be added as a relay status indicator on each channel.
*
* The Relay coil will be driven by the transistor, but the power will come from
* the 5V from the PC's USB port: Be careful in choosing the relay to avoid overloading
* the PC, as the maximum current used MUST remains under ~450mA @ 5V.
*
* The author's tested relays are 2 Finder 32.21.7.005.2000, coil il 125ohm, which can
* handle 5A @ 250VAC. Be careful to use proper isolation if high voltages are manipulated.
* The author used Hotglue to isolate all parts of the PCB in contact with high voltage.
*
* See <a>http://www.pjrc.com/teensy/</a> for the Teensy2++ website.
*
* <table>
* <tr>
* <td><b>Signal:</b></td>
* <td><b>AVR Port:</b></td>
* </tr>
* <tr>
* <td>Relay 1</td>
* <td>PORTC, Pin 4</td>
* </tr>
* <tr>
* <td>Relay 2</td>
* <td>PORTC, Pin 5</td>
* </tr>
* <tr>
* <td>Relay 3</td>
* <td>PORTC, Pin 6</td>
* </tr>
* <tr>
* <td>Relay 4</td>
* <td>PORTC, Pin 7</td>
* </tr>
* <tr>
* <td>Teensy2++ Yellow Led</td>
* <td>PORTD, pin 6</td>
* </tr>
* </table>
*
* \section Sec_Options Project Options
*
* The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td>
* None
* </td>
* </tr>
* </table>
*/
|
