aboutsummaryrefslogtreecommitdiffstats
path: root/Projects/RelayBoard/RelayBoard.txt
blob: 4b190dfe3248c740e6555c56883662c41ec245e5 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
/** \file
 *
 *  This file contains special DoxyGen information for the generation of the main page and other special
 *  documentation pages. It is not a project source file.
 */

/** \mainpage OB's Quad-Relay outlet control using a Teensy2++
 *
 *  \section Sec_Compat Project Compatibility:
 *
 *  The following list indicates what microcontrollers are compatible with this project.
 *
 *  \li AT90USB1286
 *
 *  \section Sec_Info USB Information:
 *
 *  The following table gives a rundown of the USB utilization of this project.
 *
 * <table>
 *  <tr>
 *   <td><b>USB Mode:</b></td>
 *   <td>Device</td>
 *  </tr>
 *  <tr>
 *   <td><b>USB Class:</b></td>
 *   <td>None</td>
 *  </tr>
 *  <tr>
 *   <td><b>USB Subclass:</b></td>
 *   <td>None</td>
 *  </tr>
 *  <tr>
 *   <td><b>Relevant Standards:</b></td>
 *   <td>USB Standards</td>
 *  </tr>
 *  <tr>
 *   <td><b>Supported USB Speeds:</b></td>
 *   <td>Low Speed Mode, Full Speed Mode</td>
 *  </tr>
 * </table>
 *
 *  \section Sec_Description Project Description:
 *
 *  Firmware for a Teensy2++ AVR-based miniboard to control four relays, using the
 *  same protocol used by the commercially available Silver Shield PM power outlets
 *  ( http://sourceforge.net/projects/sispmctl ) sold for some time. Because this
 *  project mimics the original device, it can be controlled using the "sismpctl"
 *  package included in many Linux distributions - including router-orientated
 *  versions such as OpenWRT - to control the board's relays.
 *
 *  Relays 1 to 4 are respectively wired to pins C4, C5, C6 and C7 of the Teensy++ V2,
 *  which are the PORTC bits 4 to 7 of the AT90USB1286. The relays MUST be wired through
 *  a transistor, and a diode must be added in antiparallel on the relay's coil pins to
 *  protect the transistor from back EMF generated from the relay when the coil is turned off.
 *  The transistor base pin is wired to the Teensy data port through a 10K resistor. A
 *  LED may be also be added as a relay status indicator on each channel.
 *
 *  The Relay coil will be driven by the transistor, but the power will come from
 *  the 5V from the PC's USB port: Be careful in choosing the relay to avoid overloading
 *  the PC, as the maximum current used MUST remains under ~450mA @ 5V.
 *
 *  The author's tested relays are 2 Finder 32.21.7.005.2000, coil il 125ohm, which can
 *  handle 5A @ 250VAC. Be careful to use proper isolation if high voltages are manipulated.
 *  The author used Hotglue to isolate all parts of the PCB in contact with high voltage.
 *
 *  See <a>http://www.pjrc.com/teensy/</a> for the Teensy2++ website.
 *
 *  <table>
 *   <tr>
 *    <td><b>Signal:</b></td>
 *    <td><b>AVR Port:</b></td>
 *   </tr>
 *   <tr>
 *    <td>Relay 1</td>
 *    <td>PORTC, Pin 4</td>
 *   </tr>
 *   <tr>
 *    <td>Relay 2</td>
 *    <td>PORTC, Pin 5</td>
 *   </tr>
 *   <tr>
 *    <td>Relay 3</td>
 *    <td>PORTC, Pin 6</td>
 *   </tr>
 *   <tr>
 *    <td>Relay 4</td>
 *    <td>PORTC, Pin 7</td>
 *   </tr>
 *   <tr>
 *    <td>Teensy2++ Yellow Led</td>
 *    <td>PORTD, pin 6</td>
 *   </tr>
 *  </table>
 *
 *  \section Sec_Options Project Options
 *
 *  The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
 *
 *  <table>
 *   <tr>
 *    <td>
 *     None
 *    </td>
 *   </tr>
 *  </table>
 */