1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage AVRISP MKII Programmer Project
*
* \section SSec_Compat Project Compatibility:
*
* The following list indicates what microcontrollers are compatible with this project.
*
* - Series 7 USB AVRs
* - Series 6 USB AVRs
* - Series 4 USB AVRs
* - Series 2 USB AVRs (8KB versions with reduced features only)
*
* \section SSec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this project.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Vendor Specific Class</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>N/A</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>Atmel AVRISP MKII Protocol Specification</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section SSec_Description Project Description:
*
* Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
* microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
* most basic form, it allows for the programming of 5V AVRs from within AVRStudio with no special hardware other than
* the USB AVR and the parts needed for the USB interface. If the user desires, more advanced circuits incorporating
* level conversion can be made to allow for the programming of 3.3V AVR designs.
*
* This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII
* drivers. When prompted, direct your OS to install Atmel's AVRISP-MKII drivers provided with AVRStudio.
*
* Note that this design currently has several limitations:
* - Minimum ISP target clock speed of 500KHz due to hardware SPI used
* - No reversed/shorted target connector detection and notification
*
* On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
* set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
* without an ADC converter, VTARGET will report at a fixed 5V level.
*
* When compiled for the XPLAIN board target, this will automatically configure itself for the correct connections to the
* XPLAIN's XMEGA AVR, and will enable PDI only programming support (since ISP and TPI modes are not needed).
*
* While this application can be compiled for USB AVRs with as little as 8KB of FLASH, for full functionality 16KB or more
* of FLASH is required. On 8KB devices, ISP, PDI or TPI programming support can be disabled to reduce program size.
*
* \section Sec_ISP ISP Connections
* Connections to the device for SPI programming (when enabled):
*
* <table>
* <tr>
* <td><b>Programmer Pin:</b></td>
* <td><b>Target Device Pin:</b></td>
* <td><b>ISP 6 Pin Layout:</b></td>
* </tr>
* <tr>
* <td>MISO</td>
* <td>PDO</td>
* <td>1</td>
* </tr>
* <tr>
* <td>ADCx <b><sup>1</sup></b></td>
* <td>VTARGET</td>
* <td>2</td>
* </tr>
* <tr>
* <td>SCLK</td>
* <td>SCLK</td>
* <td>3</td>
* </tr>
* <tr>
* <td>MOSI</td>
* <td>PDI</td>
* <td>4</td>
* </tr>
* <tr>
* <td>PORTx.y <b><sup>2</sup></b></td>
* <td>/RESET</td>
* <td>5</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>GND</td>
* <td>6</td>
* </tr>
* </table>
*
* <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
* <b><sup>2</sup></b> <i>See \ref SSec_Options section</i>
*
* \section Sec_PDI PDI Connections
* Connections to the device for PDI programming<b><sup>1</sup></b> (when enabled):
*
* <table>
* <tr>
* <td><b>Programmer Pin:</b></td>
* <td><b>Target Device Pin:</b></td>
* <td><b>PDI 6 Pin Layout:</b></td>
* </tr>
* <tr>
* <td>MISO</td>
* <td>DATA</td>
* <td>1</td>
* </tr>
* <tr>
* <td>ADCx <b><sup>1</sup></b></td>
* <td>VTARGET</td>
* <td>2</td>
* </tr>
* <tr>
* <td>N/A</td>
* <td>N/A</td>
* <td>3</td>
* </tr>
* <tr>
* <td>N/A</td>
* <td>N/A</td>
* <td>4</td>
* </tr>
* <tr>
* <td>PORTx.y <b><sup>2</sup></b></td>
* <td>CLOCK</td>
* <td>5</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>GND</td>
* <td>6</td>
* </tr>
* </table>
*
* <b><sup>1</sup></b> <i>When PDI_VIA_HARDWARE_USART is set, the AVR's Tx and Rx become the DATA line when connected together
* via a pair of 300 ohm resistors, and the AVR's XCK pin becomes CLOCK.</i>
*
* \section Sec_TPI TPI Connections
* Connections to the device for TPI programming<b><sup>1</sup></b> (when enabled):
*
* <table>
* <tr>
* <td><b>Programmer Pin:</b></td>
* <td><b>Target Device Pin:</b></td>
* <td><b>PDI 6 Pin Layout:</b></td>
* </tr>
* <tr>
* <td>MISO</td>
* <td>DATA</td>
* <td>1</td>
* </tr>
* <tr>
* <td>ADCx <b><sup>1</sup></b></td>
* <td>VTARGET</td>
* <td>2</td>
* </tr>
* <tr>
* <td>SCLK</td>
* <td>CLOCK</td>
* <td>3</td>
* </tr>
* <tr>
* <td>N/A</td>
* <td>N/A</td>
* <td>4</td>
* </tr>
* <tr>
* <td>PORTx.y <b><sup>2</sup></b></td>
* <td>/RESET</td>
* <td>5</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>GND</td>
* <td>6</td>
* </tr>
* </table>
*
* <b><sup>1</sup></b> <i>When TPI_VIA_HARDWARE_USART is set, the AVR's Tx and Rx become the DATA line when connected together
* via a pair of 300 ohm resistors, and the AVR's XCK pin becomes CLOCK.</i>
*
* \section SSec_Options Project Options
*
* The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td><b>Define Name:</b></td>
* <td><b>Location:</b></td>
* <td><b>Description:</b></td>
* </tr>
* <tr>
* <td>RESET_LINE_PORT</td>
* <td>Makefile CDEFS</td>
* <td>PORT register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>RESET_LINE_PIN</td>
* <td>Makefile CDEFS</td>
* <td>PIN register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>RESET_LINE_DDR</td>
* <td>Makefile CDEFS</td>
* <td>DDR register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>RESET_LINE_MASK</td>
* <td>Makefile CDEFS</td>
* <td>Mask for the programmer's target RESET line on the chosen port. <b>Must not be the AVR's /SS pin</b>, as the
* target pins are tri-stated when not in use, and low signals on the /SS pin will force SPI slave mode when the
* pin is configured as an input. When in PDI programming mode, this is the target clock pin.
* <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>VTARGET_ADC_CHANNEL</td>
* <td>Makefile CDEFS</td>
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection.</td>
* </tr>
* <tr>
* <td>ENABLE_ISP_PROTOCOL</td>
* <td>Makefile CDEFS</td>
* <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>ENABLE_PDI_PROTOCOL</td>
* <td>Makefile CDEFS</td>
* <td>Define to enable XMEGA PDI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>ENABLE_TPI_PROTOCOL</td>
* <td>Makefile CDEFS</td>
* <td>Define to enable 6-PIN ATTINY TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>PDI_VIA_HARDWARE_USART</td>
* <td>Makefile CDEFS</td>
* <td>Define to force the PDI protocol (when enabled) to use the much faster hardware USART instead of bit-banging to
* match the official AVRISP pinout. This breaks pinout compatibility with the official AVRISP MKII (and requires
* seperate ISP and PDI programming headers) but increases programming speed dramatically.
* <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>TPI_VIA_HARDWARE_USART</td>
* <td>Makefile CDEFS</td>
* <td>Define to force the TPI protocol (when enabled) to use the much faster hardware USART instead of bit-banging to
* match the official AVRISP pinout. This breaks pinout compatibility with the official AVRISP MKII (and requires
* seperate ISP and TPI programming headers) but increases programming speed dramatically.
* <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* </table>
*/
|