1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*
LUFA Library
Copyright (C) Dean Camera, 2011.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Main source file for the AVRISP project. This file contains the main tasks of
* the project and is responsible for the initial application hardware configuration.
*/
#include "AVRISP-MKII.h"
/** Main program entry point. This routine contains the overall program flow, including initial
* setup of all components and the main program loop.
*/
int main(void)
{
SetupHardware();
V2Protocol_Init();
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
sei();
for (;;)
{
#if (BOARD == BOARD_USBTINYMKII)
/* On the USBTINY-MKII target, there is a secondary LED which indicates the current selected power
mode - either VBUS, or sourced from the VTARGET pin of the programming connectors */
LEDs_ChangeLEDs(LEDMASK_VBUSPOWER, (PIND & (1 << 0)) ? 0 : LEDMASK_VBUSPOWER);
#endif
AVRISP_Task();
USB_USBTask();
}
}
/** Configures the board hardware and chip peripherals for the demo's functionality. */
void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Disable clock division */
clock_prescale_set(clock_div_1);
/* Hardware Initialization */
LEDs_Init();
USB_Init();
}
/** Event handler for the library USB Connection event. */
void EVENT_USB_Device_Connect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the library USB Disconnection event. */
void EVENT_USB_Device_Disconnect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the library USB Configuration Changed event. */
void EVENT_USB_Device_ConfigurationChanged(void)
{
bool ConfigSuccess = true;
/* Setup AVRISP Data Endpoint(s) */
ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_OUT_EPNUM, EP_TYPE_BULK, ENDPOINT_DIR_OUT,
AVRISP_DATA_EPSIZE, ENDPOINT_BANK_SINGLE);
#if defined(LIBUSB_DRIVER_COMPAT)
ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_IN_EPNUM, EP_TYPE_BULK, ENDPOINT_DIR_IN,
AVRISP_DATA_EPSIZE, ENDPOINT_BANK_SINGLE);
#endif
/* Indicate endpoint configuration success or failure */
LEDs_SetAllLEDs(ConfigSuccess ? LEDMASK_USB_READY : LEDMASK_USB_ERROR);
}
/** Processes incoming V2 Protocol commands from the host, returning a response when required. */
void AVRISP_Task(void)
{
/* Device must be connected and configured for the task to run */
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
V2Params_UpdateParamValues();
Endpoint_SelectEndpoint(AVRISP_DATA_OUT_EPNUM);
/* Check to see if a V2 Protocol command has been received */
if (Endpoint_IsOUTReceived())
{
LEDs_SetAllLEDs(LEDMASK_BUSY);
/* Pass off processing of the V2 Protocol command to the V2 Protocol handler */
V2Protocol_ProcessCommand();
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
}
|
