1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage CDC Class USB AVR Bootloader
*
* \section Sec_Compat Demo Compatibility:
*
* The following list indicates what microcontrollers are compatible with this demo.
*
* \li Series 7 USB AVRs (AT90USBxxx7)
* \li Series 6 USB AVRs (AT90USBxxx6)
* \li Series 4 USB AVRs (ATMEGAxxU4)
* \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2)
*
* \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this demo.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Communications Device Class (CDC)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Abstract Control Model (ACM)</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF CDC Class Standard</td>
* </tr>
* <tr>
* <td><b>Supported USB Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section Sec_Description Project Description:
*
* This bootloader enumerates to the host as a CDC Class device (virtual serial port), allowing for AVR109
* protocol compatible programming software to load firmware onto the AVR.
*
* Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
* into 4KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to
* edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
*
* When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
* bootloader from the normal user application.
*
* \section Sec_Installation Driver Installation
*
* After running this bootloader for the first time on a new computer, you will need to supply the .INF
* file located in this bootloader project's directory as the device's driver when running under Windows.
* This will enable Windows to use its inbuilt CDC drivers, negating the need for custom drivers for the
* device. Other Operating Systems should automatically use their own inbuilt CDC-ACM drivers.
*
* \section Sec_HostApp Host Controller Application
*
* This bootloader is compatible with the open source application AVRDUDE, Atmel's AVRPROG, or other
* applications implementing the AVR109 protocol, which is documented on the Atmel website as an application
* note.
*
* \subsection SSec_AVRDude AVRDUDE (Windows, Mac, Linux)
*
* AVRDude is a free, cross-platform and open source command line programmer for Atmel and third party AVR
* programmers. It is available on the the Windows platform as part of the "WinAVR" package, or on other systems
* either from a build from the official source code, or in many distributions as a precompiled binary package.
*
* To load a new HEX file with AVRDude, specify "AVR109" as the programmer, with the allocated COM port. On Windows
* platforms this will be a COMx port name:
* \code
* avrdude -c AVR109 -p at90usb1287 -P COM0 -U flash:w:Mouse.hex
* \endcode
*
* On Linux systems, this will typically be a /dev/ttyACMx port name:
* \code
* avrdude -c AVR109 -p at90usb1287 -P /dev/ttyACM0 -U flash:w:Mouse.hex
* \endcode
*
* Refer to the AVRDude project documentation for additional usage instructions.
*
* \section Sec_API User Application API
*
* Several user application functions for FLASH and other special memory area manipulations are exposed by the bootloader,
* allowing the user application to call into the bootloader at runtime to read and write FLASH data.
*
* By default, the bootloader API jump table is located 32 bytes from the end of the device's FLASH memory, and follows the
* following layout:
*
* \code
* #define BOOTLOADER_API_TABLE_SIZE 32
* #define BOOTLOADER_API_TABLE_START ((FLASHEND + 1UL) - BOOTLOADER_API_TABLE_SIZE)
* #define BOOTLOADER_API_CALL(Index) (void*)((BOOTLOADER_API_TABLE_START + (Index * 2)) / 2)
*
* void (*BootloaderAPI_ErasePage)(uint32_t Address) = BOOTLOADER_API_CALL(0);
* void (*BootloaderAPI_WritePage)(uint32_t Address) = BOOTLOADER_API_CALL(1);
* void (*BootloaderAPI_FillWord)(uint32_t Address, uint16_t Word) = BOOTLOADER_API_CALL(2);
* uint8_t (*BootloaderAPI_ReadSignature)(uint16_t Address) = BOOTLOADER_API_CALL(3);
* uint8_t (*BootloaderAPI_ReadFuse)(uint16_t Address) = BOOTLOADER_API_CALL(4);
* uint8_t (*BootloaderAPI_ReadLock)(void) = BOOTLOADER_API_CALL(5);
* void (*BootloaderAPI_WriteLock)(uint8_t LockBits) = BOOTLOADER_API_CALL(6);
*
* #define BOOTLOADER_MAGIC_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 2))
* #define BOOTLOADER_MAGIC_SIGNATURE 0xDCFB
*
* #define BOOTLOADER_CLASS_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 4))
* #define BOOTLOADER_CDC_SIGNATURE 0xCDC1
*
* #define BOOTLOADER_ADDRESS_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 8))
* #define BOOTLOADER_ADDRESS_LENGTH 4
* \endcode
*
* \subsection SSec_API_MemLayout Device Memory Map
* The following illustration indicates the final memory map of the device when loaded with the bootloader.
*
* \verbatim
* +----------------------------+ 0x0000
* | |
* | |
* | |
* | |
* | |
* | |
* | |
* | |
* | User Application |
* | |
* | |
* | |
* | |
* | |
* | |
* | |
* +----------------------------+ FLASHEND - BOOT_SECTION_SIZE
* | |
* | Bootloader Application |
* | (Not User App. Accessible) |
* | |
* +----------------------------+ FLASHEND - 96
* | API Table Trampolines |
* | (Not User App. Accessible) |
* +----------------------------+ FLASHEND - 32
* | Bootloader API Table |
* | (User App. Accessible) |
* +----------------------------+ FLASHEND - 8
* | Bootloader ID Constants |
* | (User App. Accessible) |
* +----------------------------+ FLASHEND
* \endverbatim
*
* Bootloaders reporting a device release revision number of 1.00 or greater are bootloader API enabled. From the application
* the API support of the bootloader can be detected by reading the FLASH memory bytes located at address \c BOOTLOADER_MAGIC_SIGNATURE_START
* and comparing them to the value \c BOOTLOADER_MAGIC_SIGNATURE. The class of bootloader can be determined by reading the
* FLASH memory bytes located at address \c BOOTLOADER_CLASS_SIGNATURE_START and comparing them to the value \c BOOTLOADER_CDC_SIGNATURE.
* The start address of the bootloader can be retrieved by reading the bytes of FLASH memory starting from address \c BOOTLOADER_ADDRESS_START.
*
* \section Sec_Options Project Options
*
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td><b>Define Name:</b></td>
* <td><b>Location:</b></td>
* <td><b>Description:</b></td>
* </tr>
* <tr>
* <td>NO_BLOCK_SUPPORT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable memory block read/write support in the bootloader, requiring all reads and writes to be made
* using the byte-level commands.</td>
* </tr>
* <tr>
* <td>NO_EEPROM_BYTE_SUPPORT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable EEPROM memory byte read/write support in the bootloader, requiring all EEPROM reads and writes
* to be made using the block-level commands.</td>
* </tr>
* <tr>
* <td>NO_FLASH_BYTE_SUPPORT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable FLASH memory byte read/write support in the bootloader, requiring all FLASH reads and writes
* to be made using the block-level commands.</td>
* </tr>
* <tr>
* <td>NO_LOCK_BYTE_WRITE_SUPPORT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable lock byte write support in the bootloader, preventing the lock bits from being set programmatically.</td>
* </tr>
* </table>
*/
|
