diff options
Diffstat (limited to 'LUFA/DoxygenPages/ConfiguringApps.txt')
| -rw-r--r-- | LUFA/DoxygenPages/ConfiguringApps.txt | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/LUFA/DoxygenPages/ConfiguringApps.txt b/LUFA/DoxygenPages/ConfiguringApps.txt index ece9dd59b..171198e4e 100644 --- a/LUFA/DoxygenPages/ConfiguringApps.txt +++ b/LUFA/DoxygenPages/ConfiguringApps.txt @@ -18,7 +18,7 @@ * * \see \ref Page_BuildSystem for information on the LUFA build system. * - * \section Sec_AppMakefileParams The Default Application Makefile Template + * \section Sec_ConfiguringApps_AppMakefileParams The Default Application Makefile Template * * Below is a copy of the default LUFA application makefile, which can be used as a template for each application. * @@ -41,21 +41,21 @@ * * These values should be changed to reflect the build hardware. * - * \subsection SSec_MCU The MCU Parameter + * \subsection SSec_ConfiguringApps_MCU The MCU Parameter * This parameter indicates the target microcontroller model for the compiled application. This should be set to the model of the target * microcontroller (such as the AT90USB1287, or the ATMEGA32U4), in all lower-case (e.g. "at90usb1287"). Note that not all demos support all the * microcontroller models and architectures, as they may make use of peripherals or modes only present in some devices. * * For supported processor models, see \ref Page_DeviceSupport. * - * \subsection SSec_ARCH The ARCH Parameter + * \subsection SSec_ConfiguringApps_ARCH The ARCH Parameter * This parameter indicates the target microcontroller architecture the library is to be compiled for. Different microcontroller * architectures require different source files to be compiled into the final binary, and so this option must be set to the correct * architecture for the selected platform. * * For supported processor architectures, see \ref Page_DeviceSupport. * - * \subsection SSec_BOARD The BOARD Parameter + * \subsection SSec_ConfiguringApps_BOARD The BOARD Parameter * This parameter indicates the target board hardware for the compiled application. Some LUFA library drivers are board-specific, * such as the LED driver, and the library needs to know the layout of the target board. If you are using one of the board models listed * on the main library page, change this parameter to the board name in all UPPER-case. @@ -68,37 +68,37 @@ * * For boards with built in hardware driver support within the LUFA library, see \ref Page_DeviceSupport. * - * \subsection SSec_F_CPU The F_CPU Parameter + * \subsection SSec_ConfiguringApps_F_CPU The F_CPU Parameter * This parameter indicates the target microcontroller's main CPU clock frequency, in Hz. This is used by many libraries (and applications) for * timing related purposes, and should reflect the actual CPU speed after any prescaling or adjustments are performed. * - * \subsection SSec_F_USB The F_USB Parameter + * \subsection SSec_ConfiguringApps_F_USB The F_USB Parameter * This parameter indicates the raw input clock frequency to the USB module within the microcontroller in Hz. This may be very different on some platforms * to the main CPU clock or other peripheral/bus clocks. * - * \subsection SSec_OPTIMIZATION The OPTIMIZATION Parameter + * \subsection SSec_ConfiguringApps_OPTIMIZATION The OPTIMIZATION Parameter * This parameter indicates the level of optimization to use when compiling the application. This will allow you to compile with an optimization level * supported by GCC, from <tt>0</tt> (no optimization) to <tt>3</tt> (fastest runtime optimization) or <tt>s</tt> (smallest size). * - * \subsection SSec_TARGET The TARGET Parameter + * \subsection SSec_ConfiguringApps_TARGET The TARGET Parameter * This parameter indicates the application target name, which is used as the base filename for the build binary and debugging files. This will be the * name of the output files once linked together into the final application, ready to load into the target. * - * \subsection SSec_SRC The SRC Parameter + * \subsection SSec_ConfiguringApps_SRC The SRC Parameter * This parameter indicates the source files used to compile the application, as a list of C (<tt>*.c</tt>), C++ (<tt>*.cpp</tt>) and Assembly (<tt>*.S</tt>) files. Note that * all assembly files must end in a <b>capital</b> .S extension, as lowercase .s files are reserved for GCC intermediate files. * - * \subsection SSec_LUFA_PATH The LUFA_PATH Parameter + * \subsection SSec_ConfiguringApps_LUFA_PATH The LUFA_PATH Parameter * As each LUFA program requires the LUFA library source code to compile correctly, the application must know where the LUFA library is located. This * value specifies the path to the LUFA library core. This path may be relative or absolute, however note than even under Windows based systems the * forward-slash (/) path seperator must be used. * - * \subsection SSec_CC_FLAGS The CC_FLAGS Parameter + * \subsection SSec_ConfiguringApps_CC_FLAGS The CC_FLAGS Parameter * This parameter lists the compiler flags passed to the C/C++ compiler, the assembler and the linker. These are used as-is directly to GCC and thus * must match GCC's command line options as given in the GCC manual. This variable may be used to define tokens directly on the command line, enable or * disable warnings, adjust the target-specific tuning parameters or other options. * - * \subsection SSec_LD_FLAGS The LD_FLAGS Parameter + * \subsection SSec_ConfiguringApps_LD_FLAGS The LD_FLAGS Parameter * This parameter lists the linker flags passed exclusively to the linker. These are used as-is directly to GCC and thus must match GCC's command line * linker options as given in the GCC manual. This variable may be used to create or relocate custom data sections, or enable linker specific behaviors. */ |