diff options
Diffstat (limited to 'Demos/Host/ClassDriver/GenericHIDHost/makefile')
| -rw-r--r-- | Demos/Host/ClassDriver/GenericHIDHost/makefile | 734 |
1 files changed, 0 insertions, 734 deletions
diff --git a/Demos/Host/ClassDriver/GenericHIDHost/makefile b/Demos/Host/ClassDriver/GenericHIDHost/makefile deleted file mode 100644 index b912b2ff8..000000000 --- a/Demos/Host/ClassDriver/GenericHIDHost/makefile +++ /dev/null @@ -1,734 +0,0 @@ -# Hey Emacs, this is a -*- makefile -*-
-#----------------------------------------------------------------------------
-# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
-# >> Modified for use with the LUFA project. <<
-#
-# Released to the Public Domain
-#
-# Additional material for this makefile was written by:
-# Peter Fleury
-# Tim Henigan
-# Colin O'Flynn
-# Reiner Patommel
-# Markus Pfaff
-# Sander Pool
-# Frederik Rouleau
-# Carlos Lamas
-# Dean Camera
-# Opendous Inc.
-# Denver Gingerich
-#
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device, using avrdude.
-# Please customize the avrdude settings below first!
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-# have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-# have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-# (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-# (must have Atmel FLIP installed).
-#
-# make doxygen = Generate DoxyGen documentation for the project (must have
-# DoxyGen installed)
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-# with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-# bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-
-# MCU name
-MCU = at90usb1287
-
-
-# Target board (see library "Board Types" documentation, USER or blank for projects not requiring
-# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
-# "Board" inside the application directory.
-BOARD = USBKEY
-
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-# Typical values are:
-# F_CPU = 1000000
-# F_CPU = 1843200
-# F_CPU = 2000000
-# F_CPU = 3686400
-# F_CPU = 4000000
-# F_CPU = 7372800
-# F_CPU = 8000000
-# F_CPU = 11059200
-# F_CPU = 14745600
-# F_CPU = 16000000
-# F_CPU = 18432000
-# F_CPU = 20000000
-F_CPU = 8000000
-
-
-# Input clock frequency.
-# This will define a symbol, F_CLOCK, in all source code files equal to the
-# input clock frequency (before any prescaling is performed). This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_CLOCK = 8000000
-
-
-# Output format. (can be srec, ihex, binary)
-FORMAT = ihex
-
-
-# Target file name (without extension).
-TARGET = GenericHIDHost
-
-
-# Object files directory
-# To put object files in current directory, use a dot (.), do NOT make
-# this an empty or blank macro!
-OBJDIR = .
-
-
-# Path to the LUFA library
-LUFA_PATH = ../../..
-
-
-# List C source files here. (C dependencies are automatically generated.)
-SRC = $(TARGET).c \
- ConfigDescriptor.c \
- $(LUFA_PATH)/LUFA/Scheduler/Scheduler.c \
- $(LUFA_PATH)/LUFA/Drivers/Peripheral/SerialStream.c \
- $(LUFA_PATH)/LUFA/Drivers/Peripheral/Serial.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/DevChapter9.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Endpoint.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Host.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/HostChapter9.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/LowLevel.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Pipe.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/Events.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBInterrupt.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBTask.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/ConfigDescriptor.c \
- $(LUFA_PATH)/LUFA/Drivers/USB/Class/Host/HIDParser.c \
-
-
-# List C++ source files here. (C dependencies are automatically generated.)
-CPPSRC =
-
-
-# List Assembler source files here.
-# Make them always end in a capital .S. Files ending in a lowercase .s
-# will not be considered source files but generated files (assembler
-# output from the compiler), and will be deleted upon "make clean"!
-# Even though the DOS/Win* filesystem matches both .s and .S the same,
-# it will preserve the spelling of the filenames, and gcc itself does
-# care about how the name is spelled on its command-line.
-ASRC =
-
-
-# Optimization level, can be [0, 1, 2, 3, s].
-# 0 = turn off optimization. s = optimize for size.
-# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
-
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
-# AVR Studio 4.10 requires dwarf-2.
-# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
-DEBUG = dwarf-2
-
-
-# List any extra directories to look for include files here.
-# Each directory must be seperated by a space.
-# Use forward slashes for directory separators.
-# For a directory that has spaces, enclose it in quotes.
-EXTRAINCDIRS = $(LUFA_PATH)/
-
-
-# Compiler flag to set the C Standard level.
-# c89 = "ANSI" C
-# gnu89 = c89 plus GCC extensions
-# c99 = ISO C99 standard (not yet fully implemented)
-# gnu99 = c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-
-
-# Place -D or -U options here for C sources
-CDEFS = -DF_CPU=$(F_CPU)UL -DF_CLOCK=$(F_CLOCK)UL -DBOARD=BOARD_$(BOARD)
-CDEFS += -DUSE_NONSTANDARD_DESCRIPTOR_NAMES -DNO_STREAM_CALLBACKS -DUSB_HOST_ONLY
-CDEFS += -DUSE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
-
-# Place -D or -U options here for ASM sources
-ADEFS = -DF_CPU=$(F_CPU)
-
-
-# Place -D or -U options here for C++ sources
-CPPDEFS = -DF_CPU=$(F_CPU)UL
-#CPPDEFS += -D__STDC_LIMIT_MACROS
-#CPPDEFS += -D__STDC_CONSTANT_MACROS
-
-
-
-#---------------- Compiler Options C ----------------
-# -g*: generate debugging information
-# -O*: optimization level
-# -f...: tuning, see GCC manual and avr-libc documentation
-# -Wall...: warning level
-# -Wa,...: tell GCC to pass this to the assembler.
-# -adhlns...: create assembler listing
-CFLAGS = -g$(DEBUG)
-CFLAGS += $(CDEFS)
-CFLAGS += -O$(OPT)
-CFLAGS += -funsigned-char
-CFLAGS += -funsigned-bitfields
-CFLAGS += -ffunction-sections
-CFLAGS += -fpack-struct
-CFLAGS += -fshort-enums
-CFLAGS += -finline-limit=20
-CFLAGS += -Wall
-CFLAGS += -Wstrict-prototypes
-CFLAGS += -Wundef
-#CFLAGS += -fno-unit-at-a-time
-#CFLAGS += -Wunreachable-code
-#CFLAGS += -Wsign-compare
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
-CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
-CFLAGS += $(CSTANDARD)
-
-
-#---------------- Compiler Options C++ ----------------
-# -g*: generate debugging information
-# -O*: optimization level
-# -f...: tuning, see GCC manual and avr-libc documentation
-# -Wall...: warning level
-# -Wa,...: tell GCC to pass this to the assembler.
-# -adhlns...: create assembler listing
-CPPFLAGS = -g$(DEBUG)
-CPPFLAGS += $(CPPDEFS)
-CPPFLAGS += -O$(OPT)
-CPPFLAGS += -funsigned-char
-CPPFLAGS += -funsigned-bitfields
-CPPFLAGS += -fpack-struct
-CPPFLAGS += -fshort-enums
-CPPFLAGS += -fno-exceptions
-CPPFLAGS += -Wall
-CFLAGS += -Wundef
-#CPPFLAGS += -mshort-calls
-#CPPFLAGS += -fno-unit-at-a-time
-#CPPFLAGS += -Wstrict-prototypes
-#CPPFLAGS += -Wunreachable-code
-#CPPFLAGS += -Wsign-compare
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
-CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
-#CPPFLAGS += $(CSTANDARD)
-
-
-#---------------- Assembler Options ----------------
-# -Wa,...: tell GCC to pass this to the assembler.
-# -adhlns: create listing
-# -gstabs: have the assembler create line number information; note that
-# for use in COFF files, additional information about filenames
-# and function names needs to be present in the assembler source
-# files -- see avr-libc docs [FIXME: not yet described there]
-# -listing-cont-lines: Sets the maximum number of continuation lines of hex
-# dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
-
-
-#---------------- Library Options ----------------
-# Minimalistic printf version
-PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
-
-# Floating point printf version (requires MATH_LIB = -lm below)
-PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
-
-# If this is left blank, then it will use the Standard printf version.
-PRINTF_LIB =
-#PRINTF_LIB = $(PRINTF_LIB_MIN)
-#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
-
-
-# Minimalistic scanf version
-SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
-
-# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
-SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
-
-# If this is left blank, then it will use the Standard scanf version.
-SCANF_LIB =
-#SCANF_LIB = $(SCANF_LIB_MIN)
-#SCANF_LIB = $(SCANF_LIB_FLOAT)
-
-
-MATH_LIB = -lm
-
-
-# List any extra directories to look for libraries here.
-# Each directory must be seperated by a space.
-# Use forward slashes for directory separators.
-# For a directory that has spaces, enclose it in quotes.
-EXTRALIBDIRS =
-
-
-
-#---------------- External Memory Options ----------------
-
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),
-# used for variables (.data/.bss) and heap (malloc()).
-#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
-
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),
-# only used for heap (malloc()).
-#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
-
-EXTMEMOPTS =
-
-
-
-#---------------- Linker Options ----------------
-# -Wl,...: tell GCC to pass this to linker.
-# -Map: create map file
-# --cref: add cross reference to map file
-LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
-LDFLAGS += -Wl,--relax
-LDFLAGS += -Wl,--gc-sections
-LDFLAGS += $(EXTMEMOPTS)
-LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
-LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
-#LDFLAGS += -T linker_script.x
-
-
-
-#---------------- Programming Options (avrdude) ----------------
-
-# Programming hardware: alf avr910 avrisp bascom bsd
-# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
-#
-# Type: avrdude -c ?
-# to get a full listing.
-#
-AVRDUDE_PROGRAMMER = jtagmkII
-
-# com1 = serial port. Use lpt1 to connect to parallel port.
-AVRDUDE_PORT = usb
-
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level. Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-
-
-#---------------- Debugging Options ----------------
-
-# For simulavr only - target MCU frequency.
-DEBUG_MFREQ = $(F_CPU)
-
-# Set the DEBUG_UI to either gdb or insight.
-# DEBUG_UI = gdb
-DEBUG_UI = insight
-
-# Set the debugging back-end to either avarice, simulavr.
-DEBUG_BACKEND = avarice
-#DEBUG_BACKEND = simulavr
-
-# GDB Init Filename.
-GDBINIT_FILE = __avr_gdbinit
-
-# When using avarice settings for the JTAG
-JTAG_DEV = /dev/com1
-
-# Debugging port used to communicate between GDB / avarice / simulavr.
-DEBUG_PORT = 4242
-
-# Debugging host used to communicate between GDB / avarice / simulavr, normally
-# just set to localhost unless doing some sort of crazy debugging when
-# avarice is running on a different computer.
-DEBUG_HOST = localhost
-
-
-
-#============================================================================
-
-
-# Define programs and commands.
-SHELL = sh
-CC = avr-gcc
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-AR = avr-ar rcs
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-REMOVEDIR = rm -rf
-COPY = cp
-WINSHELL = cmd
-
-# Define Messages
-# English
-MSG_ERRORS_NONE = Errors: none
-MSG_BEGIN = -------- begin --------
-MSG_END = -------- end --------
-MSG_SIZE_BEFORE = Size before:
-MSG_SIZE_AFTER = Size after:
-MSG_COFF = Converting to AVR COFF:
-MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
-MSG_FLASH = Creating load file for Flash:
-MSG_EEPROM = Creating load file for EEPROM:
-MSG_EXTENDED_LISTING = Creating Extended Listing:
-MSG_SYMBOL_TABLE = Creating Symbol Table:
-MSG_LINKING = Linking:
-MSG_COMPILING = Compiling C:
-MSG_COMPILING_CPP = Compiling C++:
-MSG_ASSEMBLING = Assembling:
-MSG_CLEANING = Cleaning project:
-MSG_CREATING_LIBRARY = Creating library:
-
-
-
-
-# Define all object files.
-OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
-
-# Define all listing files.
-LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
-
-
-# Compiler flags to generate dependency files.
-GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
-
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
-ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-
-
-
-# Default target.
-all: begin gccversion sizebefore build checkhooks checklibmode checkboard sizeafter end
-
-# Change the build target to build a HEX file or a library.
-build: elf hex eep lss sym
-#build: lib
-
-
-elf: $(TARGET).elf
-hex: $(TARGET).hex
-eep: $(TARGET).eep
-lss: $(TARGET).lss
-sym: $(TARGET).sym
-LIBNAME=lib$(TARGET).a
-lib: $(LIBNAME)
-
-
-
-# Eye candy.
-# AVR Studio 3.x does not check make's exit code but relies on
-# the following magic strings to be generated by the compile job.
-begin:
- @echo
- @echo $(MSG_BEGIN)
-
-end:
- @echo $(MSG_END)
- @echo
-
-
-# Display size of file.
-HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
-ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
-MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
-FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
-
-sizebefore:
- @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
- 2>/dev/null; echo; fi
-
-sizeafter:
- @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
- 2>/dev/null; echo; fi
-
-checkhooks: build
- @echo
- @echo ------- Unhooked LUFA Events -------
- @$(shell) (grep -s '^EVENT_.*LUFA/.*\\.o' $(TARGET).map | \
- cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
- echo "(None)"
- @echo ------------------------------------
-
-checklibmode:
- @echo
- @echo ----------- Library Mode -----------
- @$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \
- | grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \
- || echo "No specific mode (both device and host mode allowable)."
- @echo ------------------------------------
-
-checkboard:
- @echo
- @echo ---------- Selected Board ----------
- @echo Selected board model is $(BOARD).
- @echo ------------------------------------
-
-# Display compiler version information.
-gccversion :
- @$(CC) --version
-
-
-
-# Program the device.
-program: $(TARGET).hex $(TARGET).eep
- $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-
-flip: $(TARGET).hex
- batchisp -hardware usb -device $(MCU) -operation erase f
- batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
- batchisp -hardware usb -device $(MCU) -operation start reset 0
-
-dfu: $(TARGET).hex
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
- dfu-programmer $(MCU) reset
-
-flip-ee: $(TARGET).hex $(TARGET).eep
- copy $(TARGET).eep $(TARGET)eep.hex
- batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
- batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
- batchisp -hardware usb -device $(MCU) -operation start reset 0
-
-dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
- dfu-programmer $(MCU) reset
-
-
-# Generate avr-gdb config/init file which does the following:
-# define the reset signal, load the target file, connect to target, and set
-# a breakpoint at main().
-gdb-config:
- @$(REMOVE) $(GDBINIT_FILE)
- @echo define reset >> $(GDBINIT_FILE)
- @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
- @echo end >> $(GDBINIT_FILE)
- @echo file $(TARGET).elf >> $(GDBINIT_FILE)
- @echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
-ifeq ($(DEBUG_BACKEND),simulavr)
- @echo load >> $(GDBINIT_FILE)
-endif
- @echo break main >> $(GDBINIT_FILE)
-
-debug: gdb-config $(TARGET).elf
-ifeq ($(DEBUG_BACKEND), avarice)
- @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
- @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
- $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
- @$(WINSHELL) /c pause
-
-else
- @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
- $(DEBUG_MFREQ) --port $(DEBUG_PORT)
-endif
- @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
-
-
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT = $(OBJCOPY) --debugging
-COFFCONVERT += --change-section-address .data-0x800000
-COFFCONVERT += --change-section-address .bss-0x800000
-COFFCONVERT += --change-section-address .noinit-0x800000
-COFFCONVERT += --change-section-address .eeprom-0x810000
-
-
-
-coff: $(TARGET).elf
- @echo
- @echo $(MSG_COFF) $(TARGET).cof
- $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
-
-
-extcoff: $(TARGET).elf
- @echo
- @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
- $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
-
-
-
-# Create final output files (.hex, .eep) from ELF output file.
-%.hex: %.elf
- @echo
- @echo $(MSG_FLASH) $@
- $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-%.eep: %.elf
- @echo
- @echo $(MSG_EEPROM) $@
- -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
- --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
-
-# Create extended listing file from ELF output file.
-%.lss: %.elf
- @echo
- @echo $(MSG_EXTENDED_LISTING) $@
- $(OBJDUMP) -h -z -S $< > $@
-
-# Create a symbol table from ELF output file.
-%.sym: %.elf
- @echo
- @echo $(MSG_SYMBOL_TABLE) $@
- $(NM) -n $< > $@
-
-
-
-# Create library from object files.
-.SECONDARY : $(TARGET).a
-.PRECIOUS : $(OBJ)
-%.a: $(OBJ)
- @echo
- @echo $(MSG_CREATING_LIBRARY) $@
- $(AR) $@ $(OBJ)
-
-
-# Link: create ELF output file from object files.
-.SECONDARY : $(TARGET).elf
-.PRECIOUS : $(OBJ)
-%.elf: $(OBJ)
- @echo
- @echo $(MSG_LINKING) $@
- $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
-
-
-# Compile: create object files from C source files.
-$(OBJDIR)/%.o : %.c
- @echo
- @echo $(MSG_COMPILING) $<
- $(CC) -c $(ALL_CFLAGS) $< -o $@
-
-
-# Compile: create object files from C++ source files.
-$(OBJDIR)/%.o : %.cpp
- @echo
- @echo $(MSG_COMPILING_CPP) $<
- $(CC) -c $(ALL_CPPFLAGS) $< -o $@
-
-
-# Compile: create assembler files from C source files.
-%.s : %.c
- $(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Compile: create assembler files from C++ source files.
-%.s : %.cpp
- $(CC) -S $(ALL_CPPFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-$(OBJDIR)/%.o : %.S
- @echo
- @echo $(MSG_ASSEMBLING) $<
- $(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-# Create preprocessed source for use in sending a bug report.
-%.i : %.c
- $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-
-
-# Target: clean project.
-clean: begin clean_list clean_binary end
-
-clean_binary:
- $(REMOVE) $(TARGET).hex
-
-clean_list:
- @echo $(MSG_CLEANING)
- $(REMOVE) $(TARGET).eep
- $(REMOVE) $(TARGET)eep.hex
- $(REMOVE) $(TARGET).cof
- $(REMOVE) $(TARGET).elf
- $(REMOVE) $(TARGET).map
- $(REMOVE) $(TARGET).sym
- $(REMOVE) $(TARGET).lss
- $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
- $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
- $(REMOVE) $(SRC:.c=.s)
- $(REMOVE) $(SRC:.c=.d)
- $(REMOVE) $(SRC:.c=.i)
- $(REMOVEDIR) .dep
-
-
-doxygen:
- @echo Generating Project Documentation...
- @doxygen Doxygen.conf
- @echo Documentation Generation Complete.
-
-clean_doxygen:
- rm -rf Documentation
-
-# Create object files directory
-$(shell mkdir $(OBJDIR) 2>/dev/null)
-
-
-# Include the dependency files.
--include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
-
-
-# Listing of phony targets.
-.PHONY : all checkhooks checklibmode checkboard \
-begin finish end sizebefore sizeafter gccversion \
-build elf hex eep lss sym coff extcoff clean \
-clean_list clean_binary program debug gdb-config \
-doxygen dfu flip flip-ee dfu-ee
\ No newline at end of file |