Clean up excessive whitespace at the end of each line using the wspurify tool made by Laszlo Monda

1 files changed, 11 insertions, 10 deletions

diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.txt b/Projects/AVRISP-MKII/AVRISP-MKII.txt
index eb6431477..e36ffe231 100644
--- a/Projects/AVRISP-MKII/AVRISP-MKII.txt
+++ b/Projects/AVRISP-MKII/AVRISP-MKII.txt
@@ -3,7 +3,7 @@
  *  This file contains special DoxyGen information for the generation of the main page and other special
  *  documentation pages. It is not a project source file.
  */
- 
+
 /** \mainpage AVRISP MKII Programmer Project
  *
  *  \section SSec_Compat Project Compatibility:
@@ -28,7 +28,7 @@
  *   <td><b>USB Class:</b></td>
  *   <td>Vendor Specific Class</td>
  *  </tr>
- *  <tr> 
+ *  <tr>
  *   <td><b>USB Subclass:</b></td>
  *   <td>N/A</td>
  *  </tr>
@@ -42,7 +42,7 @@
  *  </tr>
  * </table>
  *
- *  \section SSec_Description Project Description: 
+ *  \section SSec_Description Project Description:
  *
  *  Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
  *  microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
@@ -240,31 +240,31 @@
  *    <td>VTARGET_ADC_CHANNEL</td>
  *    <td>Makefile LUFA_OPTS</td>
  *    <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined.
- *        <i>Ignored when compiled for targets lacking an ADC.</i></td> 
+ *        <i>Ignored when compiled for targets lacking an ADC.</i></td>
  *   </tr>
  *   <tr>
  *    <td>ENABLE_ISP_PROTOCOL</td>
  *    <td>Makefile LUFA_OPTS</td>
- *    <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>  
+ *    <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
  *   </tr>
  *   <tr>
  *    <td>ENABLE_XPROG_PROTOCOL</td>
  *    <td>Makefile LUFA_OPTS</td>
- *    <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>  
+ *    <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
  *   </tr>
  *   <tr>
  *    <td>NO_VTARGET_DETECT</td>
  *    <td>Makefile LUFA_OPTS</td>
  *    <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer
  *        to report a fixed 5V target voltage to the host regardless of the real target voltage. <i>Ignored when compiled for
- *        targets lacking an ADC.</i></td>  
+ *        targets lacking an ADC.</i></td>
  *   </tr>
  *   <tr>
  *    <td>VTARGET_REF_VOLTS</td>
  *    <td>Makefile LUFA_OPTS</td>
  *    <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply
  *        voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage
- *        to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
+ *        to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
  *   </tr>
  *   <tr>
  *    <td>VTARGET_SCALE_FACTOR</td>
@@ -272,8 +272,8 @@
  *    <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the
  *        ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be
  *        measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set
- *        to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
- *   </tr> 
+ *        to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
+ *   </tr>
  *   <tr>
  *    <td>LIBUSB_DRIVER_COMPAT</td>
  *    <td>Makefile LUFA_OPTS</td>
@@ -282,3 +282,4 @@
  *   </tr>
  *  </table>
  */
+