Seperated out parts of the PrinterHost incomplete demo into a seperate Lib subdirectory.

Fixed Host mode to Device mode UID change not causing a USB Disconnect event when a device was connected.

4 files changed, 21 insertions, 7 deletions

diff --git a/LUFA/ManPages/Author.jpg b/LUFA/ManPages/Author.jpg
index 71e1a08fb..e8f5541a0 100644
--- a/LUFA/ManPages/Author.jpg
+++ b/LUFA/ManPages/Author.jpg
diff --git a/LUFA/ManPages/ChangeLog.txt b/LUFA/ManPages/ChangeLog.txt
index 3ad2097ab..0f582a657 100644
--- a/LUFA/ManPages/ChangeLog.txt
+++ b/LUFA/ManPages/ChangeLog.txt
@@ -49,6 +49,7 @@
   *  - Fixed MassStorage demo not clearing the reset flag when a Mass Storage Reset is issued while not processing a command

   *  - Fixed USB_Host_SendControlRequest() not re-suspending the USB bus when initial device ready-wait fails

   *  - Fixed USB Pad regulator not being disabled on some AVR models when the USB_OPT_REG_DISABLED option is used

+  *  - Fixed Host mode to Device mode UID change not causing a USB Disconnect event when a device was connected

   *

   *

   *  \section Sec_ChangeLog090605 Version 090605

diff --git a/LUFA/ManPages/ConfiguringApps.txt b/LUFA/ManPages/ConfiguringApps.txt
index bb6d185e4..fb9da7094 100644
--- a/LUFA/ManPages/ConfiguringApps.txt
+++ b/LUFA/ManPages/ConfiguringApps.txt
@@ -24,7 +24,9 @@
  *    - <b>BOARD</b>, the target board hardware

  *    - <b>F_CLOCK</b>, the target raw master clock frequency, before any prescaling is performed

  *    - <b>F_CPU</b>, the target AVR CPU master clock frequency, after any prescaling

- *    - <b>CDEFS</b>, the C preprocessor defines which configure the source code

+ *    - <b>CDEFS</b>, the C preprocessor defines which configure options the source code

+ *    - <b>LUFA_PATH</b>, the path to the LUFA library source code

+ *    - <b>LUFA_OPTS</b>, the compile time LUFA options which configure the library features

  *

  *  These values should be changed to reflect the build hardware.

  *

@@ -63,12 +65,23 @@
  *  library components will occur.

  *

  *  \section Sec_CDEFS The CDEFS Parameter

+ *  Many applications have features which can be controlled by the defining of specially named preprocessor tokens at the point of compilation - for example,

+ *  an application might use a compile time token to turn on or off optional or mutually exclusive portions of code. Preprocessor tokens can be

+ *  defined here by listing each one with the -D command line switch, and each token can optionally be defined to a specific value. When defined in the

+ *  project makefile, these behave as if they were defined in every source file via a normal preprocessor define statement.

+ *

  *  Most applications will actually have multiple CDEF lines, which are concatenated together with the "+=" operator. This ensures that large

  *  numbers of configuration options remain readable by splitting up groups of options into separate lines.

  *

- *  Normally, these options do not need to be altered to allow an application to compile and run correctly on a different board or AVR to the

- *  current configuration - if the options are incorrect, then the demo is most likely incompatible with the chosen USB AVR model and cannot be

- *  made to function through the altering of the makefile settings alone (or at all). Settings such as the USB mode (device, host or both), the USB

- *  interface speed (Low or Full speed) and other LUFA configuration options can be set here - refer to the library documentation for details on the

- *  configuration parameters.

+ *  \section Sec_LUFA_PATH The LUFA_PATH Parameter

+ *  As each LUFA program requires the LUFA library source code to compile correctly, the application must know where the LUFA library is located. This

+ *  value specifies the path to the LUFA library base relative to the path of the project makefile.

+ *

+ *  \section Sec_LUFA_OPTS The LUFA_OPTS Parameter

+ *  This value is similar to the CDEFS parameter listed elsewhere -- indeed, it is simply a convenient place to group LUFA related tokens away from the

+ *  application's compile time tokens. Normally, these options do not need to be altered to allow an application to compile and run correctly on a

+ *  different board or AVR to the current configuration - if the options are incorrect, then the demo is most likely incompatible with the chosen USB AVR

+ *  model and cannot be made to function through the altering of the makefile settings alone (or at all). Settings such as the USB mode (device, host or both),

+ *  the USB interface speed (Low or Full speed) and other LUFA configuration options can be set here - see \ref Page_TokenSummary documentation for details

+ *  on the available LUFA compile time configuration options.

  */
\ No newline at end of file
diff --git a/LUFA/ManPages/FutureChanges.txt b/LUFA/ManPages/FutureChanges.txt
index 1a2b7a031..59a279072 100644
--- a/LUFA/ManPages/FutureChanges.txt
+++ b/LUFA/ManPages/FutureChanges.txt
@@ -21,11 +21,11 @@
   *  - Add standardized descriptor names to device and host class driver structures

   *  - Remove USE_NONSTANDARD_DESCRIPTOR_NAMES, make all typedefs unions to allow either naming scheme to be used

   *  - Add in INTERRUPT_CONTROL_PIPE to use HSOFI to trigger calls to the host state machine

-  *  - Remove FAST_STREAM_TRANSFERS as they have little effect

   *  - Make Suspend host state suspend USB bus frames

   *  - Add in Stream functions for PROGMEM, EEPROM -- move to templated system

   *  - Debug mode for pipe/endpoint calls

   *  - Test and document new FAST_STREAM_TRANSFERS compile time option

+  *  - Demo hardware compatibility table/list

   *

   *  <b>Targeted for Future Releases:</b>

   *  - Remake AVRStudio project files