Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

1 files changed, 62 insertions, 62 deletions

diff --git a/LUFA/ManPages/SoftwareBootloaderJump.txt b/LUFA/ManPages/SoftwareBootloaderJump.txt
index 3f6e30582..1b284e4cd 100644
--- a/LUFA/ManPages/SoftwareBootloaderJump.txt
+++ b/LUFA/ManPages/SoftwareBootloaderJump.txt
@@ -1,63 +1,63 @@
-/** \file

- *

- *  This file contains special DoxyGen information for the generation of the main page and other special

- *  documentation pages. It is not a project source file.

- */

-

-/**

- *  \page Page_SoftwareBootloaderStart Entering the Bootloader via Software

- *

- *  A common requirement of many applications is the ability to jump to the programmed bootloader of a chip

- *  on demand, via the code's firmware (i.e. not as a result of any physical user interaction with the

- *  hardware). This might be required because the device does not have any physical user input, or simply

- *  just to streamline the device upgrade process on the host PC.

- *

- *  The following C code snippet may be used to enter the bootloader upon request by the user application.

- *  By using the watchdog to physically reset the controller, it is ensured that all system hardware is

- *  completely reset to their defaults before the bootloader is run. This is important; since bootloaders

- *  are written to occupy a very limited space, they usually make assumptions about the register states based

- *  on the default values after a hard-reset of the chip.

- *

- *  \code

- *  #include <avr/wdt.h>

- *  #include <avr/io.h>

- *  #include <util/delay.h>

- *

- *  #include <LUFA/Common/Common.h>

- *  #include <LUFA/Drivers/USB/USB.h>

- *

- *  uint32_t Boot_Key ATTR_NO_INIT;

- *

- *  #define MAGIC_BOOT_KEY            0xDC42ACCA

- *  #define BOOTLOADER_START_ADDRESS  ({FLASH_SIZE_BYTES} - {BOOTLOADER_SEC_SIZE_BYTES})

- *  

- *  void Bootloader_Jump_Check(void) ATTR_INIT_SECTION(3);

- *  void Bootloader_Jump_Check(void)

- *  {

- *      // If the reset source was the bootloader and the key is correct, clear it and jump to the bootloader

- *      if ((MCUSR & (1<<WDRF)) && (Boot_Key == MAGIC_BOOT_KEY))

- *      {

- *          Boot_Key = 0;

- *          ((void (*)(void))BOOTLOADER_START_ADDRESS)(); 

- *      }

- *  }

- *

- *  void Jump_To_Bootloader(void)

- *  {

- *      // If USB is used, detatch from the bus and wait 2 seconds for the host to register it

- *      USB_ShutDown();

- *      for (uint8_t i = 0; i < 128; i++)

- *        _delay_ms(16);

- *

- *      // Set the bootloader key to the magic value and force a reset

- *      Boot_Key = MAGIC_BOOT_KEY;

- *      wdt_enable(WDTO_250MS);

- *      for (;;); 

- *  }

- *  \endcode

- *

- *  Note that the bootloader magic key can be any arbitrary value. The {FLASH_SIZE_BYTES} and

- *  {BOOTLOADER_SEC_SIZE_BYTES} tokens should be replaced with the total flash size of the AVR

- *  in bytes, and the allocated size of the bootloader section for the target AVR.

- * 

+/** \file
+ *
+ *  This file contains special DoxyGen information for the generation of the main page and other special
+ *  documentation pages. It is not a project source file.
+ */
+
+/**
+ *  \page Page_SoftwareBootloaderStart Entering the Bootloader via Software
+ *
+ *  A common requirement of many applications is the ability to jump to the programmed bootloader of a chip
+ *  on demand, via the code's firmware (i.e. not as a result of any physical user interaction with the
+ *  hardware). This might be required because the device does not have any physical user input, or simply
+ *  just to streamline the device upgrade process on the host PC.
+ *
+ *  The following C code snippet may be used to enter the bootloader upon request by the user application.
+ *  By using the watchdog to physically reset the controller, it is ensured that all system hardware is
+ *  completely reset to their defaults before the bootloader is run. This is important; since bootloaders
+ *  are written to occupy a very limited space, they usually make assumptions about the register states based
+ *  on the default values after a hard-reset of the chip.
+ *
+ *  \code
+ *  #include <avr/wdt.h>
+ *  #include <avr/io.h>
+ *  #include <util/delay.h>
+ *
+ *  #include <LUFA/Common/Common.h>
+ *  #include <LUFA/Drivers/USB/USB.h>
+ *
+ *  uint32_t Boot_Key ATTR_NO_INIT;
+ *
+ *  #define MAGIC_BOOT_KEY            0xDC42ACCA
+ *  #define BOOTLOADER_START_ADDRESS  ({FLASH_SIZE_BYTES} - {BOOTLOADER_SEC_SIZE_BYTES})
+ *  
+ *  void Bootloader_Jump_Check(void) ATTR_INIT_SECTION(3);
+ *  void Bootloader_Jump_Check(void)
+ *  {
+ *      // If the reset source was the bootloader and the key is correct, clear it and jump to the bootloader
+ *      if ((MCUSR & (1<<WDRF)) && (Boot_Key == MAGIC_BOOT_KEY))
+ *      {
+ *          Boot_Key = 0;
+ *          ((void (*)(void))BOOTLOADER_START_ADDRESS)(); 
+ *      }
+ *  }
+ *
+ *  void Jump_To_Bootloader(void)
+ *  {
+ *      // If USB is used, detatch from the bus and wait 2 seconds for the host to register it
+ *      USB_ShutDown();
+ *      for (uint8_t i = 0; i < 128; i++)
+ *        _delay_ms(16);
+ *
+ *      // Set the bootloader key to the magic value and force a reset
+ *      Boot_Key = MAGIC_BOOT_KEY;
+ *      wdt_enable(WDTO_250MS);
+ *      for (;;); 
+ *  }
+ *  \endcode
+ *
+ *  Note that the bootloader magic key can be any arbitrary value. The {FLASH_SIZE_BYTES} and
+ *  {BOOTLOADER_SEC_SIZE_BYTES} tokens should be replaced with the total flash size of the AVR
+ *  in bytes, and the allocated size of the bootloader section for the target AVR.
+ * 
  */
\ No newline at end of file