diff options
Diffstat (limited to 'keyboards')
29 files changed, 2816 insertions, 0 deletions
diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile new file mode 100644 index 000000000..12a4b71f4 --- /dev/null +++ b/keyboards/handwired/traveller/Makefile @@ -0,0 +1,89 @@ + +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# for avr upload +USB ?= /dev/cu.usbmodem1421 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# MCU name + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +RGBLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +upload: build + $(ATREUS_UPLOAD_COMMAND) + diff --git a/keyboards/handwired/traveller/config.h b/keyboards/handwired/traveller/config.h new file mode 100644 index 000000000..2b82da447 --- /dev/null +++ b/keyboards/handwired/traveller/config.h @@ -0,0 +1,173 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER You +#define PRODUCT traveller +#define DESCRIPTION A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 13 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D3, D2 } + // no I can't say why this order seemed like a good idea +#define MATRIX_COL_PINS { B5, D6, B7, B6, F6, B1, B3, F7, B4, E6, D7, C6, D4 } +#define UNUSED_PINS + +// LED stuff +#define RGB_DI_PIN B2 +//#define RBLIGHT_TIMER +#define RGBLED_NUM 1 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/traveller/keymaps/default/keymap.c b/keyboards/handwired/traveller/keymaps/default/keymap.c new file mode 100644 index 000000000..13d889ab8 --- /dev/null +++ b/keyboards/handwired/traveller/keymaps/default/keymap.c @@ -0,0 +1,305 @@ +#include "traveller.h" +#include "mousekey.h" +#include "action_layer.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +#define _QW 0 +#define _LW 1 +#define _HI 2 +#define _NAV 4 +#define _CUR 5 +#define _FKEYS 6 +#define _TRNS 8 + +// We do the same trick for functions +#define RGBLED_TOGGLE 10 +#define _HIOUT 15 +#define _LWOUT 16 +// Macros +#define MDL 4 +#define MDR 5 +#define MUR 6 +#define MUL 3 + + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty + * ,-----------------------------------------. .-----------------------------------------. + * | NAV | ` ~ | W | E | R | T | | Y | U | I | O | - | = | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Tab | Q | S | D | F | G | | H | J | K | L | P | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + *|ctrl/esc| A | X | C | V | B |Ctrl /| N | M | , | . | ; | ' | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | Shift| Z | Del | GUI | Low | Bspc |/Enter| Spc | Hi | GUI | Alt | / |Shift | + * `------------------------------------------------------------------------------------------' + * + */ +[_QW] = KEYMAP( + F(_NAV), KC_GRV, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_MINS, KC_EQL, + KC_TAB, KC_Q, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_P, KC_BSLS, + CTL_T(KC_ESC), KC_A, KC_X, KC_C, KC_V, KC_B, KC_RCTL, KC_N, KC_M, KC_COMM, KC_DOT, KC_SCLN, KC_QUOT, + KC_LSFT, KC_Z, KC_DEL, KC_LGUI, MO(_LW), KC_BSPC, KC_ENTER, KC_SPC, MO(_HI), KC_RGUI, KC_RALT, KC_SLSH, KC_RSFT + ), + +/* LOW - numbers, missing or awkward programming keys + Doubled 1 key allows lazy reach with ring finger. + * ,-----------------------------------------. .-----------------------------------------. + * | FKeys| 1 | 2 | 3 | 4 | 5 | | 6 | 7 | 8 | 9 | 0 |Ctrl-alt-del| + * |------+------+------+------+------+------| +------+------+------+------+------+------| + * | Tab | 1 | ] | ( | ) | | | * | ( | ) | [ | | | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | Caps | [ | | { | } | ` | /| # | { | } | | ] | | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | Shift| | | | Low | |/ | | Hi | | | |Shift | + * `------------------------------------------------------------------------------------------' + * + */ + +[_LW] = KEYMAP( + F(_FKEYS), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, LCTL(LALT(KC_DEL)) , + KC_TRNS, KC_1, KC_RBRC, KC_LPRN, KC_RPRN, KC_NO, KC_ASTR, KC_LPRN, KC_RPRN, KC_LBRC, KC_NO, KC_NO, + KC_CAPS, KC_LBRC, KC_NO, KC_LCBR, KC_RCBR, KC_TILD, KC_TRNS, KC_HASH, KC_LCBR, KC_RCBR, KC_NO, KC_RBRC, KC_NO, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS +), + +/* HI - Punctuation, shell and +url ://@.com row on bottom, && is opposite || ^$ are in regex order: ^.*$ +Right hand nav keys work pretty well chorded with the Right hand Hi Key + * ,-----------------------------------------. .-----------------------------------------. + * |FKEYS | ! | @ | # | $ | % | | ^ | & | * | ( | ) | + | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | | ! | & | "|" | $ | % | | Vol+| Mute| | | | | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | CAPS | ^ | : | . | * | - | /| Vol-| Play | PgUp | Home | Up | End | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | | / | | | Low | |/ | | Hi | PgDn | Left| Down | Right | + * `------------------------------------------------------------------------------------------' + * + */ + +[_HI] = KEYMAP( + F(_FKEYS), KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_PLUS, + KC_TRNS, KC_EXLM, KC_AMPR, KC_PIPE, KC_DLR, KC_PERC, KC_VOLU, KC_MUTE, KC_NO, KC_NO, KC_NO, KC_NO, + KC_CAPS, KC_CIRC, KC_COLN, KC_DOT, KC_ASTR, KC_MINS, KC_TRNS, KC_VOLD, KC_PPLS, KC_PGUP, KC_HOME, KC_UP, KC_END, + KC_TRNS, KC_SLSH, KC_TRNS, KC_TRNS, F(_LW), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGDN, KC_LEFT, KC_DOWN, KC_RIGHT +), + +/* NAV - mouse & navigation +//gui left and right are line home/end, or fore & back in browser +// Mouse buttons are reversed for comfort - bigger stretch is to the right button. + + * ,-----------------------------------------. .-----------------------------------------. +* | NAV | | | Up | |Gui-> | | MwU | MS_UL| MS_U |MS_UR | |Ms Norm| +* |------+------+------+------+------+------| |------+------+------+------+------+--------| +* | |Gui<- | Left | Down |Right | C^E | | BTN3 | MS_L |MS Up | MS_R | |Ms Fast | +* |------+------+------+------+------+------|------|------+------+------+------+------+--------| +* | | C^A | GUI X| GUI C| GUI_V| |Enter/| MWD | M_DL |MS Dwn|MS_DR | Up |Ms Slow | +* |------+------+------+------+------+------+ // +------+------+------+------+------+------| +* | | GuiZ | | | Low | |/ButnR|ButnL | Hi | | Left | Down | Right | +* `------------------------------------------------------------------------------------------' +*/ + +[_NAV] = KEYMAP( + F(_NAV), KC_NO, KC_NO, KC_UP, KC_NO, RGUI(KC_RIGHT), KC_WH_U, M(MUL), KC_MS_U, M(MUR), KC_NO, KC_ACL2, + KC_TRNS, RGUI(KC_LEFT), KC_LEFT, KC_DOWN, KC_RIGHT, LCTL(KC_E), KC_BTN3, KC_MS_L, KC_MS_U, KC_MS_R, KC_NO, KC_ACL1, + KC_TRNS, LCTL(KC_A), LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO, KC_ENTER, KC_WH_D, M(MDL), KC_MS_D, M(MDR), KC_UP, KC_ACL0, + KC_TRNS, RGUI(KC_Z), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BTN2, KC_BTN1, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT +), + +/* FKEYS - Funtion keys & mac stuff + * ,-----------------------------------------. .-----------------------------------------. + * | FKEYS| F1 | F2 | F3 | F4 | F5 | | F6 | F7 | F8 | F9 | F10 | Ctrl | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | | | | | | | | F11 | F12 | F13 | F14 | F15 | Alt | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * |Qwerty| | | | | | /| | | | | | Del | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | . |RGBTog| . | | LO | Bspc |/ | | HI | | | | | + * `------------------------------------------------------------------------------------------' + * + */ + +[_FKEYS] = KEYMAP( + F(_FKEYS), KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_RCTL, + KC_TRNS, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_LALT , + F(_QW), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_DEL, + KC_TRNS, F(RGBLED_TOGGLE), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS +), + + +/* TRNS - skeleton for laters + * ,-----------------------------------------. .-----------------------------------------. + * | . | . | . | . | . | . | | ^ | & | * | ( | ) | | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | . | . | . | . | . | . | | 6 | 7 | 8 | 9 | 0 | | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | . | . | . | . | . | . | /| | | | . | ; | " | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | . | . | . | GUI | LO | . |/ | Spc | HI | GUI | M0 | / |LSFT | + * `------------------------------------------------------------------------------------------' + * + */ + +[_TRNS] = { + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS} + } + + +}; + + +const uint16_t PROGMEM fn_actions[] = { + [_QW] = ACTION_LAYER_ON(_QW,ON_RELEASE), // return to QWERTY layer + [_LW] = ACTION_LAYER_TAP_TOGGLE(_LW), // Turn on LW when holding, or tap 3 times to switch + [_HI] = ACTION_LAYER_TAP_TOGGLE(_HI), // Turn on LW when holding, or tap 3 times to switch + [_NAV] = ACTION_LAYER_TOGGLE(_NAV), + [_FKEYS] = ACTION_LAYER_TOGGLE(_FKEYS), + [_LWOUT] = ACTION_LAYER_OFF(_LW,ON_RELEASE), + [_HIOUT] = ACTION_LAYER_OFF(_HI,ON_RELEASE), + + // Functions + [RGBLED_TOGGLE] = ACTION_FUNCTION(RGBLED_TOGGLE), + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + break; + + // from algernon's ErgoDox EZ layout, + case MUL: + if (record->event.pressed) { + mousekey_on(KC_MS_UP); + mousekey_on(KC_MS_LEFT); + } else { + mousekey_off(KC_MS_UP); + mousekey_off(KC_MS_LEFT); + } + mousekey_send(); + break; + + case MUR: + if (record->event.pressed) { + mousekey_on(KC_MS_UP); + mousekey_on(KC_MS_RIGHT); + } else { + mousekey_off(KC_MS_UP); + mousekey_off(KC_MS_RIGHT); + } + mousekey_send(); + break; + + case MDL: + if (record->event.pressed) { + mousekey_on(KC_MS_DOWN); + mousekey_on(KC_MS_LEFT); + } else { + mousekey_off(KC_MS_DOWN); + mousekey_off(KC_MS_LEFT); + } + mousekey_send(); + break; + + case MDR: + if (record->event.pressed) { + mousekey_on(KC_MS_DOWN); + mousekey_on(KC_MS_RIGHT); + } else { + mousekey_off(KC_MS_DOWN); + mousekey_off(KC_MS_RIGHT); + } + mousekey_send(); + break; + + + } + return MACRO_NONE; +}; + + + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + switch (id) { + case RGBLED_TOGGLE: + //led operations + if (record->event.pressed) { + rgblight_toggle(); + } + break; + } +} + + + +void LayerLEDSet(uint8_t layr) { + + switch (layr) { + case _QW: + rgblight_setrgb(0,20, 0); // dim green + break; + case _LW: + // deep purple + rgblight_setrgb(20,0,35); + break; + case _HI: + // light blue + rgblight_setrgb(0,20,20); + break; + case _NAV: + // Yellowy orange + rgblight_setrgb(25,20,0); // brighter + break; + case _FKEYS: + // RED + rgblight_setrgb(20,0,0); // brighter + break; + default: + rgblight_setrgb(20,2,20);//error + break; + } + + return; + +} + +void matrix_init_user(void) { +} + +// Bleah globals need to be initialized. +uint8_t old_layer=_QW; + +void matrix_scan_user(void) { + uint8_t layer = biton32(layer_state); + if (old_layer != layer) { + LayerLEDSet(layer); + old_layer=layer; + } +} + + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} + + diff --git a/keyboards/handwired/traveller/keymaps/default/readme.md b/keyboards/handwired/traveller/keymaps/default/readme.md new file mode 100644 index 000000000..7ddc40b3c --- /dev/null +++ b/keyboards/handwired/traveller/keymaps/default/readme.md @@ -0,0 +1,2 @@ +# The default keymap for handwired/traveller +this is a kitchen sink build diff --git a/keyboards/handwired/traveller/readme.md b/keyboards/handwired/traveller/readme.md new file mode 100644 index 000000000..646844b1d --- /dev/null +++ b/keyboards/handwired/traveller/readme.md @@ -0,0 +1,35 @@ +traveler keyboard firmware +====================== + +## Traveller Specific Info ## +The traveller is a varient on the atreus keyboard. +Like the Atreus, it is designed to be a good compromise between size and ergonomics. + +key differences are +- an additional column for each pinky +- an RGB LED in the center to show the current layer +- more finger stagger, splay angle and contoured keycaps (F2 profile for space key). + +You can make your own traveller keyboard by using the openscad tools from the atreus repository, and adding a hole for the LED to shine through. + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent README.md](/README.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboard/traveler folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top README.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/handwired/traveller/traveller.c b/keyboards/handwired/traveller/traveller.c new file mode 100644 index 000000000..9d2534130 --- /dev/null +++ b/keyboards/handwired/traveller/traveller.c @@ -0,0 +1,61 @@ +#include "traveller.h" + +__attribute__ ((weak)) +void matrix_init_user(void) { + // leave this function blank - it can be defined in a keymap file +}; + +__attribute__ ((weak)) +void matrix_scan_user(void) { + // leave this function blank - it can be defined in a keymap file +} + +__attribute__ ((weak)) +void process_action_user(keyrecord_t *record) { + // leave this function blank - it can be defined in a keymap file +} + +__attribute__ ((weak)) +void led_set_user(uint8_t usb_led) { + // leave this function blank - it can be defined in a keymap file +} + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + +#ifdef RGBLIGHT_ENABLE + rgblight_init(); + rgblight_mode(1); // solid, no timer + rgblight_setrgb(0,20,0);// dim green, happens to be same as _QW +#endif + +// Turn status LED on + DDRC |= (1<<7); + PORTC |= (1<<7); + + matrix_init_user(); +} + + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + + diff --git a/keyboards/handwired/traveller/traveller.h b/keyboards/handwired/traveller/traveller.h new file mode 100644 index 000000000..972a1a94a --- /dev/null +++ b/keyboards/handwired/traveller/traveller.h @@ -0,0 +1,32 @@ +#ifndef TRAVELLER_H +#define TRAVELLER_H + +#include "quantum.h" +#include "led.h" + +#ifdef RGBLIGHT_ENABLE + #include "rgblight.h" +#endif +#ifdef BACKLIGHT_ENABLE + #include "backlight.h" +#endif + + + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ + k00, k01, k02, k03, k04, k05, k07, k08, k09, k0a, k0b, k0c, \ + k10, k11, k12, k13, k14, k15, k17, k18, k19, k1a, k1b, k1c, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, KC_NO, k07, k08, k09, k0a, k0b, k0c }, \ + { k10, k11, k12, k13, k14, k15, KC_NO, k17, k18, k19, k1a, k1b, k1c }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c } \ +} + +#endif diff --git a/keyboards/kinesis/Makefile b/keyboards/kinesis/Makefile new file mode 100644 index 000000000..ca077e636 --- /dev/null +++ b/keyboards/kinesis/Makefile @@ -0,0 +1,79 @@ + +## Project specific files + +SRC= matrix.c + +# MCU name +MCU = at90usb1286 +#MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=1024 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming +CUSTOM_MATRIX=yes # need to do our own thing with the matrix + +ifndef QUANTUM_DIR + include ../../Makefile +endif + + diff --git a/keyboards/kinesis/config.h b/keyboards/kinesis/config.h new file mode 100644 index 000000000..8f1fdbdb6 --- /dev/null +++ b/keyboards/kinesis/config.h @@ -0,0 +1,174 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER You +#define PRODUCT kinesis-advantage +#define DESCRIPTION A custom keyboard + +// Mouse +#define MOUSEKEY_DELAY 20 +#define MOUSEKEY_INTERVAL 20 +#define MOUSEKEY_MAX_SPEED 4 +#define MOUSEKEY_TIME_TO_MAX 20 +#define MOUSEKEY_WHEEL_MAX_SPEED 1 +#define MOUSEKEY_WHEEL_DELTA 1 +#define MOUSEKEY_WHEEL_TIME_TO_MAX 1 + +/* key matrix size */ +#define MATRIX_ROWS 16 +#define MATRIX_COLS 8 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +//Passed through the port multipler, so 4 pins =16 +#define MATRIX_ROW_PINS { F0,F1, F2, F3 } + +// May be upside down. +#define MATRIX_COL_PINS { B0,B1, B2, B3, B4, B5, B6, B7 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/kinesis/docs/kicad/kinesis-cache.lib b/keyboards/kinesis/docs/kicad/kinesis-cache.lib new file mode 100644 index 000000000..f798d39d6 --- /dev/null +++ b/keyboards/kinesis/docs/kicad/kinesis-cache.lib @@ -0,0 +1,232 @@ +EESchema-LIBRARY Version 2.3 Date: Wednesday, November 12, 2014 'pmt' 10:15:19 pm +#encoding utf-8 +# +# AT90S4414-P +# +DEF AT90S4414-P IC 0 40 Y Y 1 F N +F0 "IC" -850 1880 40 H V L BNN +F1 "AT90S4414-P" 450 -1950 40 H V L BNN +F2 "DIL40" 0 0 30 H V C CIN +F3 "~" 0 0 60 H V C CNN +ALIAS AT90S8515-P +$FPLIST + 40DIP-ELL600 + 40dip600 +$ENDFPLIST +DRAW +S -850 1850 850 -1850 0 1 10 f +X (T0)PB0 1 1000 700 150 L 40 40 1 1 B +X (T1)PB1 2 1000 600 150 L 40 40 1 1 B +X (AIN0)PB2 3 1000 500 150 L 40 40 1 1 B +X (AIN1)PB3 4 1000 400 150 L 40 40 1 1 B +X (~SS~)PB4 5 1000 300 150 L 40 40 1 1 B +X (MOSI)PB5 6 1000 200 150 L 40 40 1 1 B +X (MISO)PB6 7 1000 100 150 L 40 40 1 1 B +X (SCK)PB7 8 1000 0 150 L 40 40 1 1 B +X ~RESET 9 -1000 1700 150 R 40 40 1 1 I +X (RXD)PD0 10 1000 -1000 150 L 40 40 1 1 B +X GND 20 0 -2000 150 U 40 40 1 1 W +X ALE 30 1000 850 150 L 40 40 1 1 O +X VCC 40 0 2000 150 D 40 40 1 1 W +X (TXD)PD1 11 1000 -1100 150 L 40 40 1 1 B +X (A8)PC0 21 1000 -150 150 L 40 40 1 1 B +X ICP 31 -1000 -1400 150 R 40 40 1 1 I +X (INT0)PD2 12 1000 -1200 150 L 40 40 1 1 B +X (A9)PC1 22 1000 -250 150 L 40 40 1 1 B +X (AD7)PA7 32 1000 1000 150 L 40 40 1 1 B +X (INT1)PD3 13 1000 -1300 150 L 40 40 1 1 B +X (A10)PC2 23 1000 -350 150 L 40 40 1 1 B +X (AD6)PA6 33 1000 1100 150 L 40 40 1 1 B +X PD4 14 1000 -1400 150 L 40 40 1 1 B +X (A11)PC3 24 1000 -450 150 L 40 40 1 1 B +X (AD5)PA5 34 1000 1200 150 L 40 40 1 1 B +X (OC1A)PD5 15 1000 -1500 150 L 40 40 1 1 B +X (A12)PC4 25 1000 -550 150 L 40 40 1 1 B +X (AD4)PA4 35 1000 1300 150 L 40 40 1 1 B +X (~WR~)PD6 16 1000 -1600 150 L 40 40 1 1 B +X (A13)PC5 26 1000 -650 150 L 40 40 1 1 B +X (AD3)PA3 36 1000 1400 150 L 40 40 1 1 B +X (~RD~)PD7 17 1000 -1700 150 L 40 40 1 1 B +X (A14)PC6 27 1000 -750 150 L 40 40 1 1 B +X (AD2)PA2 37 1000 1500 150 L 40 40 1 1 B +X XTAL2 18 -1000 1200 150 R 40 40 1 1 B +X (A15)PC7 28 1000 -850 150 L 40 40 1 1 B +X (AD1)PA1 38 1000 1600 150 L 40 40 1 1 B +X XTAL1 19 -1000 800 150 R 40 40 1 1 B +X OC1B 29 -1000 -1500 150 R 40 40 1 1 W +X (AD0)PA0 39 1000 1700 150 L 40 40 1 1 B +ENDDRAW +ENDDEF +# +# ATMEGA16U4-A +# +DEF ATMEGA16U4-A U 0 40 Y Y 1 F N +F0 "U" -950 1700 40 H V C CNN +F1 "ATMEGA16U4-A" 700 -1500 40 H V C CNN +F2 "TQFP44" 0 0 35 H V C CIN +F3 "~" 1100 1100 60 H V C CNN +ALIAS ATMEGA16U4RC-A ATMEGA32U4-A ATMEGA32U4RC-A +$FPLIST + TQFP44 +$ENDFPLIST +DRAW +S -1000 1650 950 -1450 0 1 10 f +X (INT6/AIN0)PE6 1 1100 -650 150 L 40 40 1 1 B +X UVCC 2 -450 1800 150 D 40 40 1 1 W +X D- 3 -1150 100 150 R 40 40 1 1 B +X D+ 4 -1150 200 150 R 40 40 1 1 B +X UGND 5 -400 -1600 150 U 40 40 1 1 P +X UCAP 6 -1150 -50 150 R 40 40 1 1 P +X VBUS 7 -1150 350 150 R 40 40 1 1 P +X (SS/PCINT0)PB0 8 1100 1550 150 L 40 40 1 1 B +X (SCLK/PCINT1)PB1 9 1100 1450 150 L 40 40 1 1 B +X (PDI/MOSI/PCINT2)PB2 10 1100 1350 150 L 40 40 1 1 B +X (RXD/INT2)PD2 20 1100 150 150 L 40 40 1 1 B +X (ADC13/OC1B/OC4B/PCINT13)PB6 30 1100 950 150 L 40 40 1 1 B +X (ADC1)PF1 40 1100 -950 150 L 40 40 1 1 B +X (PDO/MISO/PCINT3)PB3 11 1100 1250 150 L 40 40 1 1 B +X (TXD/INT3)PD3 21 1100 50 150 L 40 40 1 1 B +X (OC3A/~OC4A~)PC6 31 1100 650 150 L 40 40 1 1 B +X (ADC0)PF0 41 1100 -850 150 L 40 40 1 1 B +X (OC0A/OC1C/~RTS~/PCINT7)PB7 12 1100 850 150 L 40 40 1 1 B +X (XCK1/~CTS~)PD5 22 1100 -150 150 L 40 40 1 1 B +X (ICP3/CLK0/OC4A)PC7 32 1100 550 150 L 40 40 1 1 B +X AREF 42 -1150 -850 150 R 40 40 1 1 P +X ~RESET~ 13 -1150 1550 150 R 40 40 1 1 I +X GND 23 -50 -1600 150 U 40 40 1 1 W +X (~HWB~)PE2 33 1100 -550 150 L 40 40 1 1 B +X GND 43 150 -1600 150 U 40 40 1 1 W +X VCC 14 -200 1800 150 D 40 40 1 1 W +X AVCC 24 150 1800 150 D 40 40 1 1 W +X VCC 34 -100 1800 150 D 40 40 1 1 W +X AVCC 44 250 1800 150 D 40 40 1 1 W +X GND 15 -150 -1600 150 U 40 40 1 1 W +X (ICP2/ADC8)PD4 25 1100 -50 150 L 40 40 1 1 B +X GND 35 50 -1600 150 U 40 40 1 1 W +X XTAL2 16 -1150 950 150 R 40 40 1 1 O +X (T1/~OC4D~/ADC9)PD6 26 1100 -250 150 L 40 40 1 1 B +X (ADC7/TDI)PF7 36 1100 -1350 150 L 40 40 1 1 B +X XTAL1 17 -1150 1150 150 R 40 40 1 1 I +X (T0/OC4D/ADC10)PD7 27 1100 -350 150 L 40 40 1 1 B +X (ADC6/TDO)PF6 37 1100 -1250 150 L 40 40 1 1 B +X (OC0B/SCL/INT0)PD0 18 1100 350 150 L 40 40 1 1 B +X (ADC11/PCINT4)PB4 28 1100 1150 150 L 40 40 1 1 B +X (ADC5/TMS)PF5 38 1100 -1150 150 L 40 40 1 1 B +X (SDA/INT1)PD1 19 1100 250 150 L 40 40 1 1 B +X (ADC12/OC1A/~OC4B~/PCINT12)PB5 29 1100 1050 150 L 40 40 1 1 B +X (ADC4/TCK)PF4 39 1100 -1050 150 L 40 40 1 1 B +ENDDRAW +ENDDEF +# +# C +# +DEF C C 0 10 N Y 1 F N +F0 "C" 0 100 40 H V L CNN +F1 "C" 6 -85 40 H V L CNN +F2 "~" 38 -150 30 H V C CNN +F3 "~" 0 0 60 H V C CNN +$FPLIST + SM* + C? + C1-1 +$ENDFPLIST +DRAW +P 2 0 1 20 -80 -30 80 -30 N +P 2 0 1 20 -80 30 80 30 N +X ~ 1 0 200 170 D 40 40 1 1 P +X ~ 2 0 -200 170 U 40 40 1 1 P +ENDDRAW +ENDDEF +# +# CONN_7 +# +DEF CONN_7 P 0 40 Y N 1 F N +F0 "P" -30 0 60 V V C CNN +F1 "CONN_7" 70 0 60 V V C CNN +F2 "~" 0 0 60 H V C CNN +F3 "~" 0 0 60 H V C CNN +DRAW +S -100 350 150 -350 0 1 0 N +X P1 1 -350 300 250 R 50 50 1 1 P I +X P2 2 -350 200 250 R 50 50 1 1 P I +X P3 3 -350 100 250 R 50 50 1 1 P I +X P4 4 -350 0 250 R 50 50 1 1 P I +X P5 5 -350 -100 250 R 50 50 1 1 P I +X P6 6 -350 -200 250 R 50 50 1 1 P I +X P7 7 -350 -300 250 R 50 50 1 1 P I +ENDDRAW +ENDDEF +# +# GND +# +DEF ~GND #PWR 0 0 Y Y 1 F P +F0 "#PWR" 0 0 30 H I C CNN +F1 "GND" 0 -70 30 H I C CNN +F2 "~" 0 0 60 H V C CNN +F3 "~" 0 0 60 H V C CNN +DRAW +P 4 0 1 0 -50 0 0 -50 50 0 -50 0 N +X GND 1 0 0 0 U 30 30 1 1 W N +ENDDRAW +ENDDEF +# +# R +# +DEF R R 0 0 N Y 1 F N +F0 "R" 80 0 40 V V C CNN +F1 "R" 7 1 40 V V C CNN +F2 "~" -70 0 30 V V C CNN +F3 "~" 0 0 30 H V C CNN +$FPLIST + R? + SM0603 + SM0805 + R?-* + SM1206 +$ENDFPLIST +DRAW +S -40 150 40 -150 0 1 12 N +X ~ 1 0 250 100 D 60 60 1 1 P +X ~ 2 0 -250 100 U 60 60 1 1 P +ENDDRAW +ENDDEF +# +# USB-MINI-B +# +DEF USB-MINI-B CON 0 40 Y Y 1 F N +F0 "CON" -250 450 60 H V C CNN +F1 "USB-MINI-B" -50 -500 60 H V C CNN +F2 "~" 0 0 60 H V C CNN +F3 "~" 0 0 60 H V C CNN +$FPLIST + USB-Mini-B-Jack +$ENDFPLIST +DRAW +S -350 400 350 -400 0 1 0 N +X VBUS 1 -550 300 200 R 50 50 1 1 W +X D- 2 -550 150 200 R 50 50 1 1 B +X D+ 3 -550 0 200 R 50 50 1 1 B +X ID 4 -550 -150 200 R 50 50 1 1 B +X GND 5 -550 -300 200 R 50 50 1 1 W +X SHELL1 6 550 300 200 L 50 50 1 1 B +X SHELL2 7 550 150 200 L 50 50 1 1 B +X SHELL3 8 550 -150 200 L 50 50 1 1 B +X SHELL4 9 550 -300 200 L 50 50 1 1 B +ENDDRAW +ENDDEF +# +# VCC +# +DEF VCC #PWR 0 0 Y Y 1 F P +F0 "#PWR" 0 100 30 H I C CNN +F1 "VCC" 0 100 30 H V C CNN +F2 "~" 0 0 60 H V C CNN +F3 "~" 0 0 60 H V C CNN +DRAW +X VCC 1 0 0 0 U 20 20 0 0 W N +C 0 50 20 0 1 0 N +P 3 0 1 0 0 0 0 30 0 30 N +ENDDRAW +ENDDEF +# +#End Library diff --git a/keyboards/kinesis/docs/kicad/kinesis.pro b/keyboards/kinesis/docs/kicad/kinesis.pro new file mode 100644 index 000000000..9f130b509 --- /dev/null +++ b/keyboards/kinesis/docs/kicad/kinesis.pro @@ -0,0 +1,83 @@ +update=Wednesday, November 05, 2014 'pmt' 12:08:47 pm +version=1 +last_client=pcbnew +[cvpcb] +version=1 +NetIExt=net +[cvpcb/libraries] +EquName1=devcms +[general] +version=1 +[eeschema] +version=1 +PageLayoutDescrFile= +SubpartIdSeparator=0 +SubpartFirstId=65 +LibDir=../../../lib/kicad/library +NetFmtName= +RptD_X=0 +RptD_Y=100 +RptLab=1 +LabSize=60 +[eeschema/libraries] +LibName1=power +LibName2=device +LibName3=transistors +LibName4=conn +LibName5=linear +LibName6=regul +LibName7=74xx +LibName8=cmos4000 +LibName9=adc-dac +LibName10=memory +LibName11=xilinx +LibName12=special +LibName13=microcontrollers +LibName14=dsp +LibName15=microchip +LibName16=analog_switches +LibName17=motorola +LibName18=texas +LibName19=intel +LibName20=audio +LibName21=interface +LibName22=digital-audio +LibName23=philips +LibName24=display +LibName25=cypress +LibName26=siliconi +LibName27=opto +LibName28=atmel +LibName29=contrib +LibName30=valves +LibName31=custom +[pcbnew] +version=1 +LastNetListRead= +UseCmpFile=1 +PadDrill=1.016000000000 +PadDrillOvalY=1.016000000000 +PadSizeH=1.524000000000 +PadSizeV=1.524000000000 +PcbTextSizeV=1.500000000000 +PcbTextSizeH=1.500000000000 +PcbTextThickness=0.300000000000 +ModuleTextSizeV=1.000000000000 +ModuleTextSizeH=1.000000000000 +ModuleTextSizeThickness=0.150000000000 +SolderMaskClearance=0.000000000000 +SolderMaskMinWidth=0.000000000000 +DrawSegmentWidth=0.200000000000 +BoardOutlineThickness=0.100000000000 +ModuleOutlineThickness=0.150000000000 +[pcbnew/libraries] +LibDir=../../../lib/kicad/modules +LibName1=custom +LibName2=Sockets +LibName3=Connect +LibName4=Discret +LibName5=Divers +LibName6=Display +LibName7=LEDs +LibName8=SMD_Packages +LibName9=Sockets_DIP diff --git a/keyboards/kinesis/docs/kicad/kinesis.sch b/keyboards/kinesis/docs/kicad/kinesis.sch new file mode 100644 index 000000000..f75335aa0 --- /dev/null +++ b/keyboards/kinesis/docs/kicad/kinesis.sch @@ -0,0 +1,634 @@ +EESchema Schematic File Version 2 +LIBS:power +LIBS:device +LIBS:transistors +LIBS:conn +LIBS:linear +LIBS:regul +LIBS:74xx +LIBS:cmos4000 +LIBS:adc-dac +LIBS:memory +LIBS:xilinx +LIBS:special +LIBS:microcontrollers +LIBS:dsp +LIBS:microchip +LIBS:analog_switches +LIBS:motorola +LIBS:texas +LIBS:intel +LIBS:audio +LIBS:interface +LIBS:digital-audio +LIBS:philips +LIBS:display +LIBS:cypress +LIBS:siliconi +LIBS:opto +LIBS:atmel +LIBS:contrib +LIBS:valves +LIBS:custom +LIBS:kinesis-cache +EELAYER 27 0 +EELAYER END +$Descr A4 11693 8268 +encoding utf-8 +Sheet 1 1 +Title "" +Date "13 nov 2014" +Rev "" +Comp "" +Comment1 "" +Comment2 "" +Comment3 "" +Comment4 "" +$EndDescr +$Comp +L C C4 +U 1 1 545804FB +P 2850 4250 +F 0 "C4" H 2850 4350 40 0000 L CNN +F 1 "1uF" H 2856 4165 40 0000 L CNN +F 2 "~" H 2888 4100 30 0000 C CNN +F 3 "~" H 2850 4250 60 0000 C CNN + 1 2850 4250 + -1 0 0 1 +$EndComp +$Comp +L R R3 +U 1 1 545805E8 +P 2500 4000 +F 0 "R3" V 2580 4000 40 0000 C CNN +F 1 "22" V 2507 4001 40 0000 C CNN +F 2 "~" V 2430 4000 30 0000 C CNN +F 3 "~" H 2500 4000 30 0000 C CNN + 1 2500 4000 + 0 -1 -1 0 +$EndComp +$Comp +L R R2 +U 1 1 545805FA +P 2500 3800 +F 0 "R2" V 2580 3800 40 0000 C CNN +F 1 "22" V 2507 3801 40 0000 C CNN +F 2 "~" V 2430 3800 30 0000 C CNN +F 3 "~" H 2500 3800 30 0000 C CNN + 1 2500 3800 + 0 -1 -1 0 +$EndComp +Entry Wire Line + 6450 2450 6550 2550 +Entry Wire Line + 6450 2550 6550 2650 +Entry Wire Line + 6450 2650 6550 2750 +Entry Wire Line + 6450 2750 6550 2850 +Entry Wire Line + 6450 2950 6550 3050 +Entry Wire Line + 6450 3050 6550 3150 +Entry Wire Line + 6450 2850 6550 2950 +Entry Wire Line + 6450 3150 6550 3250 +Wire Wire Line + 10250 1800 10750 1800 +Entry Wire Line + 10750 1800 10850 1900 +Entry Wire Line + 10750 1900 10850 2000 +Entry Wire Line + 10750 2000 10850 2100 +Entry Wire Line + 10750 2800 10850 2900 +Entry Wire Line + 10750 2900 10850 3000 +Entry Wire Line + 10750 3000 10850 3100 +Entry Wire Line + 10750 3100 10850 3200 +Entry Wire Line + 10750 3200 10850 3300 +Entry Wire Line + 10750 3300 10850 3400 +$Comp +L AT90S8515-P IC2 +U 1 1 545A62EA +P 9250 3500 +F 0 "IC2" H 8400 5380 40 0000 L BNN +F 1 "AT90S8515-P" H 9700 1550 40 0000 L BNN +F 2 "DIL40" H 9250 3500 30 0000 C CIN +F 3 "" H 9250 3500 60 0000 C CNN + 1 9250 3500 + 1 0 0 -1 +$EndComp +NoConn ~ 10250 2650 +Entry Wire Line + 10750 3650 10850 3750 +Entry Wire Line + 10750 3750 10850 3850 +Entry Wire Line + 10750 3850 10850 3950 +Entry Wire Line + 10750 3950 10850 4050 +Entry Wire Line + 10750 4050 10850 4150 +Entry Wire Line + 10750 4150 10850 4250 +Entry Wire Line + 10750 4350 10850 4450 +Entry Wire Line + 10750 4250 10850 4350 +NoConn ~ 8250 4900 +NoConn ~ 8250 5000 +NoConn ~ 8250 1800 +Wire Wire Line + 10250 1900 10750 1900 +Wire Wire Line + 10250 2000 10750 2000 +Wire Wire Line + 10250 2100 10750 2100 +Wire Wire Line + 10250 2200 10750 2200 +Wire Wire Line + 10250 2300 10750 2300 +Wire Wire Line + 10250 2400 10750 2400 +Wire Wire Line + 10250 2500 10750 2500 +Text Label 10350 1800 0 60 ~ 0 +A +Text Label 10350 1900 0 60 ~ 0 +B +Text Label 10350 2000 0 60 ~ 0 +C +Text Label 10350 2100 0 60 ~ 0 +G +Wire Wire Line + 10250 2800 10750 2800 +Wire Wire Line + 10250 2900 10750 2900 +Wire Wire Line + 10250 3000 10750 3000 +Wire Wire Line + 10250 3100 10750 3100 +Wire Wire Line + 10250 3200 10750 3200 +Wire Wire Line + 10250 3300 10750 3300 +Wire Wire Line + 10250 3400 10750 3400 +Wire Wire Line + 10250 3500 10750 3500 +Text Label 10350 2800 0 60 ~ 0 +DL2 +Text Label 10350 2900 0 60 ~ 0 +DR1 +Text Label 10350 3000 0 60 ~ 0 +DR2 +Text Label 10350 3100 0 60 ~ 0 +DL1 +Text Label 10350 3400 0 60 ~ 0 +SCL +Text Label 10350 3500 0 60 ~ 0 +SDA +Wire Wire Line + 10250 3650 10750 3650 +Wire Wire Line + 10250 3750 10750 3750 +Wire Wire Line + 10250 3850 10750 3850 +Wire Wire Line + 10250 3950 10750 3950 +Wire Wire Line + 10250 4050 10750 4050 +Wire Wire Line + 10250 4150 10750 4150 +Wire Wire Line + 10250 4250 10750 4250 +Wire Wire Line + 10250 4350 10750 4350 +Text Label 10350 3650 0 60 ~ 0 +R1 +Text Label 10350 3750 0 60 ~ 0 +R2 +Text Label 10350 3850 0 60 ~ 0 +R3 +Text Label 10350 3950 0 60 ~ 0 +R4 +Text Label 10350 4050 0 60 ~ 0 +R5 +Text Label 10350 4150 0 60 ~ 0 +R6 +Text Label 10350 4250 0 60 ~ 0 +R7 +Text Label 10350 4350 0 60 ~ 0 +R8 +Wire Wire Line + 10250 4500 10750 4500 +Wire Wire Line + 10250 4600 10750 4600 +Wire Wire Line + 10250 4700 10750 4700 +Wire Wire Line + 10250 4800 10750 4800 +Wire Wire Line + 10250 4900 10750 4900 +Wire Wire Line + 10250 5000 10750 5000 +Wire Wire Line + 10250 5100 10750 5100 +Wire Wire Line + 10250 5200 10750 5200 +Text Label 10350 4600 0 60 ~ 0 +FS1 +Text Label 10350 5000 0 60 ~ 0 +FS3 +Text Label 10350 5200 0 60 ~ 0 +FS2 +$Comp +L GND #PWR01 +U 1 1 545A7377 +P 9250 5600 +F 0 "#PWR01" H 9250 5600 30 0001 C CNN +F 1 "GND" H 9250 5530 30 0001 C CNN +F 2 "" H 9250 5600 60 0000 C CNN +F 3 "" H 9250 5600 60 0000 C CNN + 1 9250 5600 + 1 0 0 -1 +$EndComp +Wire Wire Line + 9250 5500 9250 5600 +Text Label 10350 4700 0 60 ~ 0 +CLOCK +Text Label 10350 4800 0 60 ~ 0 +DATA +NoConn ~ 10750 4700 +NoConn ~ 10750 4800 +Text Label 10350 3200 0 60 ~ 0 +KP +Text Label 10350 3300 0 60 ~ 0 +PGM +Text Label 10350 2500 0 60 ~ 0 +BUZZ +NoConn ~ 8250 2300 +NoConn ~ 8250 2700 +$Comp +L GND #PWR02 +U 1 1 545A7565 +P 4750 5700 +F 0 "#PWR02" H 4750 5700 30 0001 C CNN +F 1 "GND" H 4750 5630 30 0001 C CNN +F 2 "" H 4750 5700 60 0000 C CNN +F 3 "" H 4750 5700 60 0000 C CNN + 1 4750 5700 + 1 0 0 -1 +$EndComp +Entry Wire Line + 6450 3650 6550 3750 +Entry Wire Line + 6450 3750 6550 3850 +Entry Wire Line + 6450 4150 6550 4250 +Entry Wire Line + 6450 4250 6550 4350 +Entry Wire Line + 6450 4050 6550 4150 +Entry Wire Line + 6450 4350 6550 4450 +NoConn ~ 3750 2850 +Wire Wire Line + 1200 2000 6450 2000 +NoConn ~ 3750 3050 +Wire Wire Line + 2750 3800 3750 3800 +Wire Wire Line + 2750 3900 3750 3900 +Wire Wire Line + 2750 3900 2750 4000 +Wire Bus Line + 6550 2100 6550 6050 +Wire Bus Line + 10850 1600 10850 6050 +Text Label 6050 4350 0 60 ~ 0 +DL1 +Text Label 6050 4250 0 60 ~ 0 +DR2 +Text Label 6050 4150 0 60 ~ 0 +DR1 +Text Label 6050 4050 0 60 ~ 0 +DL2 +Text Label 6050 2450 0 60 ~ 0 +R1 +Text Label 6050 2550 0 60 ~ 0 +R2 +Text Label 6050 2650 0 60 ~ 0 +R3 +Text Label 6050 2750 0 60 ~ 0 +R4 +Text Label 6050 2850 0 60 ~ 0 +R5 +Text Label 6050 2950 0 60 ~ 0 +R6 +Text Label 6050 3050 0 60 ~ 0 +R7 +Text Label 6050 3150 0 60 ~ 0 +R8 +Text Label 6050 5050 0 60 ~ 0 +A +Text Label 6050 5150 0 60 ~ 0 +B +Text Label 6050 5250 0 60 ~ 0 +C +Text Label 6050 5350 0 60 ~ 0 +G +Text Label 1300 3800 0 60 ~ 0 +D+ +Text Label 1300 4000 0 60 ~ 0 +D- +NoConn ~ 10750 2200 +NoConn ~ 10750 2300 +NoConn ~ 10750 2400 +Text Label 10350 4500 0 60 ~ 0 +GND +NoConn ~ 10750 4900 +NoConn ~ 10750 5100 +Text Label 6050 3450 0 60 ~ 0 +KP +Text Label 6050 3350 0 60 ~ 0 +PGM +$Comp +L ATMEGA32U4-A U1 +U 1 1 5462E0B1 +P 4900 4000 +F 0 "U1" H 3950 5700 40 0000 C CNN +F 1 "ATMEGA32U4-A" H 5600 2500 40 0000 C CNN +F 2 "TQFP44" H 4900 4000 35 0000 C CIN +F 3 "" H 6000 5100 60 0000 C CNN + 1 4900 4000 + 1 0 0 -1 +$EndComp +Wire Wire Line + 3750 4850 3750 5600 +Wire Wire Line + 4450 2200 5150 2200 +Connection ~ 4700 2200 +Connection ~ 4800 2200 +Connection ~ 5050 2200 +Connection ~ 4800 2000 +Wire Wire Line + 6000 2450 6450 2450 +Wire Wire Line + 6000 2550 6450 2550 +Wire Wire Line + 6000 2650 6450 2650 +Wire Wire Line + 6000 2750 6450 2750 +Wire Wire Line + 6000 2850 6450 2850 +Wire Wire Line + 6000 2950 6450 2950 +Wire Wire Line + 6000 3050 6450 3050 +Wire Wire Line + 6000 3150 6450 3150 +Wire Wire Line + 6000 5050 6450 5050 +Wire Wire Line + 6000 5150 6450 5150 +Wire Wire Line + 6000 5250 6450 5250 +Wire Wire Line + 6000 4050 6450 4050 +Wire Wire Line + 6000 4150 6450 4150 +Wire Wire Line + 6000 4250 6450 4250 +Wire Wire Line + 6000 4350 6450 4350 +Wire Wire Line + 6000 4550 6450 4550 +Entry Wire Line + 6450 3350 6550 3450 +Entry Wire Line + 6450 3450 6550 3550 +Entry Wire Line + 6450 5050 6550 5150 +Entry Wire Line + 6450 5150 6550 5250 +Entry Wire Line + 6450 5250 6550 5350 +Entry Wire Line + 6450 5350 6550 5450 +Entry Wire Line + 6450 4650 6550 4750 +Wire Wire Line + 6000 3350 6450 3350 +Wire Wire Line + 6000 3450 6450 3450 +Wire Wire Line + 1200 5600 6450 5600 +Connection ~ 4950 5600 +Connection ~ 4850 5600 +Wire Wire Line + 4750 5600 4750 5700 +Connection ~ 4750 5600 +Connection ~ 4500 5600 +Text Label 6050 4550 0 60 ~ 0 +HWB +Wire Wire Line + 6000 5350 6450 5350 +Wire Wire Line + 6000 3650 6450 3650 +Wire Wire Line + 6000 3750 6450 3750 +Text Label 6050 3650 0 60 ~ 0 +SCL +Text Label 6050 3750 0 60 ~ 0 +SDA +Wire Wire Line + 6000 3850 6450 3850 +Wire Wire Line + 6000 3950 6450 3950 +Wire Wire Line + 6000 4650 6450 4650 +Text Label 6050 4650 0 60 ~ 0 +BUZZ +NoConn ~ 10750 4600 +NoConn ~ 10750 5000 +NoConn ~ 10750 5200 +Entry Wire Line + 10750 3400 10850 3500 +Entry Wire Line + 10750 3500 10850 3600 +Entry Wire Line + 10750 4500 10850 4600 +Wire Wire Line + 2850 4050 3750 4050 +Text Label 2950 4050 0 60 ~ 0 +UCAP +Wire Wire Line + 6000 4850 6450 4850 +Wire Wire Line + 6000 4950 6450 4950 +NoConn ~ 6450 4850 +NoConn ~ 6450 4950 +NoConn ~ 6450 4550 +$Comp +L USB-MINI-B CON1 +U 1 1 546431C1 +P 2100 5050 +F 0 "CON1" H 1850 5500 60 0000 C CNN +F 1 "USB-MINI-B" H 2050 4550 60 0000 C CNN +F 2 "" H 2100 5050 60 0000 C CNN +F 3 "" H 2100 5050 60 0000 C CNN + 1 2100 5050 + 0 1 1 0 +$EndComp +$Comp +L VCC #PWR03 +U 1 1 54643698 +P 2400 4400 +F 0 "#PWR03" H 2400 4500 30 0001 C CNN +F 1 "VCC" H 2400 4500 30 0000 C CNN +F 2 "" H 2400 4400 60 0000 C CNN +F 3 "" H 2400 4400 60 0000 C CNN + 1 2400 4400 + 1 0 0 -1 +$EndComp +Text Notes 2600 2750 0 60 ~ 0 +Teensy 2.0\n(not fully drawn) +$Comp +L CONN_7 B7K-PH-K-S1 +U 1 1 54643939 +P 1950 6900 +F 0 "B7K-PH-K-S1" V 1920 6900 60 0000 C CNN +F 1 "CONN_7" V 2020 6900 60 0000 C CNN +F 2 "" H 1950 6900 60 0000 C CNN +F 3 "" H 1950 6900 60 0000 C CNN + 1 1950 6900 + 1 0 0 -1 +$EndComp +Connection ~ 3750 5600 +Connection ~ 2400 5600 +Connection ~ 2250 5600 +Connection ~ 1950 5600 +Wire Wire Line + 2400 4400 2400 4500 +Wire Wire Line + 2250 4000 2250 4500 +Wire Wire Line + 1200 3800 2250 3800 +Wire Wire Line + 2100 3800 2100 4500 +Wire Wire Line + 2850 4450 2850 5600 +Connection ~ 2850 5600 +Entry Wire Line + 1100 6800 1200 6900 +Entry Wire Line + 1100 6900 1200 7000 +Entry Wire Line + 1100 7000 1200 7100 +Entry Wire Line + 1100 6700 1200 6800 +Wire Wire Line + 1200 6600 1600 6600 +Wire Wire Line + 1200 6700 1600 6700 +Wire Wire Line + 1200 6800 1600 6800 +Wire Wire Line + 1200 6900 1600 6900 +Wire Wire Line + 1200 7000 1600 7000 +Wire Wire Line + 1200 7100 1600 7100 +Wire Wire Line + 1200 7200 1600 7200 +Text Label 1300 6600 0 60 ~ 0 +FS2 +Text Label 1300 6700 0 60 ~ 0 +FS1 +Text Label 1300 6800 0 60 ~ 0 +VCC +Text Label 1300 6900 0 60 ~ 0 +D- +Text Label 1300 7000 0 60 ~ 0 +D+ +Text Label 1300 7100 0 60 ~ 0 +GND +Text Label 1300 7200 0 60 ~ 0 +FS3 +NoConn ~ 3750 2450 +Wire Wire Line + 3600 2000 3600 3650 +Wire Wire Line + 3600 3650 3750 3650 +NoConn ~ 1950 4500 +Wire Bus Line + 1100 1900 1100 7100 +NoConn ~ 1200 6600 +NoConn ~ 1200 6700 +NoConn ~ 1200 7200 +Connection ~ 2100 3800 +Wire Wire Line + 1200 4000 2250 4000 +Entry Wire Line + 1100 3700 1200 3800 +Entry Wire Line + 1100 3900 1200 4000 +Text Label 10350 1500 0 60 ~ 0 +VCC +Entry Wire Line + 1100 1900 1200 2000 +Text Label 1250 2000 0 60 ~ 0 +VCC +Entry Wire Line + 1100 5500 1200 5600 +Connection ~ 1800 5600 +Text Label 1300 5600 0 60 ~ 0 +GND +Wire Wire Line + 9250 5500 10750 5500 +Entry Wire Line + 10750 5500 10850 5600 +Text Label 10350 5500 0 60 ~ 0 +GND +Wire Wire Line + 9250 1500 10750 1500 +Entry Wire Line + 10750 1500 10850 1600 +Connection ~ 3600 2000 +Wire Wire Line + 4800 2000 4800 2200 +Entry Wire Line + 6450 2000 6550 2100 +Text Label 6050 2000 0 60 ~ 0 +VCC +Connection ~ 5050 5600 +Entry Wire Line + 6450 5600 6550 5700 +Text Label 6050 5600 0 60 ~ 0 +GND +NoConn ~ 6450 3850 +NoConn ~ 6450 3950 +Wire Wire Line + 1800 4500 1500 4500 +Wire Wire Line + 1500 4500 1500 5600 +Connection ~ 1500 5600 +Entry Wire Line + 10750 2500 10850 2600 +Entry Wire Line + 10750 2100 10850 2200 +Text Notes 1000 5300 1 60 ~ 0 +Sacrificial USB cable from header to Teensy +Text Notes 7850 5950 0 60 ~ 0 +Ribbon cable between Teensy pins and socket +Wire Bus Line + 10850 6050 6550 6050 +$EndSCHEMATC diff --git a/keyboards/kinesis/docs/photos/P1050573.jpg b/keyboards/kinesis/docs/photos/P1050573.jpg Binary files differnew file mode 100644 index 000000000..027ab9efb --- /dev/null +++ b/keyboards/kinesis/docs/photos/P1050573.jpg diff --git a/keyboards/kinesis/docs/photos/P1050574.jpg b/keyboards/kinesis/docs/photos/P1050574.jpg Binary files differnew file mode 100644 index 000000000..d49c492b8 --- /dev/null +++ b/keyboards/kinesis/docs/photos/P1050574.jpg diff --git a/keyboards/kinesis/docs/photos/P1050575.jpg b/keyboards/kinesis/docs/photos/P1050575.jpg Binary files differnew file mode 100644 index 000000000..50cc9897c --- /dev/null +++ b/keyboards/kinesis/docs/photos/P1050575.jpg diff --git a/keyboards/kinesis/docs/readme.txt b/keyboards/kinesis/docs/readme.txt new file mode 100644 index 000000000..af33ac490 --- /dev/null +++ b/keyboards/kinesis/docs/readme.txt @@ -0,0 +1,52 @@ +This directory of documentation was copied from https://github.com/wjanssens/tmk_keyboard/tree/master/keyboard/kinesis +and is probably Copyright 2014 Warren Janssens <warren.janssens@gmail.com> +and probably released under GPL v2, which may be recovered at <http://www.gnu.org/licenses/>. + +Row configuration +PF0 A +PF1 B +PF2 C +PF3 G 0 = U4, 1 = U5 + +Column configuration + 4y0 4y1 4y2 4y3 4y4 4y5 4y6 4y7 5y0 5y1 5y2 5y3 5y4 5y5 5y6 5y7 + r1 r2 r3 r4 r5 r6 r7 r8 r9 r10 r11 r12 r13 r14 r15 r16 +PB0 21 c1 f6 f8 f7 5 4 3 2 1 =+ +PB1 22 c2 f3 f5 f4 t r e w q TAB +PB2 23 c3 ESC f2 f1 g f d s a CL +PB3 24 c4 f9 f11 f10 b v c x z LS UP DN [{ ]} +PB4 25 c5 f12 SL PS RT LT §± `~ 6 7 8 9 0 -_ +PB5 26 c6 PB PGM KPD y u i o p \ +PB6 27 c7 LC DL BS RC EN SP h j k l ;: '" +PB7 28 c8 RA PU PD n m ,< .> /? RS + */ + + +40 pin connector + + DL2 1 40 VCC + DR1 2 39 A + DR2 3 38 B + DL1 4 37 C + KPD 5 36 G + PGM 6 35 + SCL 7 34 + SDA 8 33 + RST 9 32 BUZZ + WP 10 31 EA + FS1 11 30 ALE + CLOCK 12 29 PSEN + DATA 13 28 r8 + 14 27 r7 + FS3 15 26 r6 + 16 25 r5 + FS2 17 24 r4 + XTAL1 18 23 r3 + XTAL2 19 22 r2 + GND 20 21 r1 + + +references: +https://github.com/chrisandreae/keyboard-firmware + + diff --git a/keyboards/kinesis/docs/schematic.png b/keyboards/kinesis/docs/schematic.png Binary files differnew file mode 100644 index 000000000..fa9405a1f --- /dev/null +++ b/keyboards/kinesis/docs/schematic.png diff --git a/keyboards/kinesis/keymaps/default/Makefile b/keyboards/kinesis/keymaps/default/Makefile new file mode 100644 index 000000000..9d3df5964 --- /dev/null +++ b/keyboards/kinesis/keymaps/default/Makefile @@ -0,0 +1,21 @@ +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/kinesis/keymaps/default/config.h b/keyboards/kinesis/keymaps/default/config.h new file mode 100644 index 000000000..8893d122e --- /dev/null +++ b/keyboards/kinesis/keymaps/default/config.h @@ -0,0 +1,8 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +// place overrides here + +#endif diff --git a/keyboards/kinesis/keymaps/default/keymap.c b/keyboards/kinesis/keymaps/default/keymap.c new file mode 100644 index 000000000..3bf80699c --- /dev/null +++ b/keyboards/kinesis/keymaps/default/keymap.c @@ -0,0 +1,116 @@ +#include "kinesis.h" +#include "action_layer.h" + +#define QWERTY 0 // Base qerty +#define SYMB 1// Symbol layer + +// An almost entirely blank keymap. Test layers with the upper right hand key - 1 in normal mode, reset in layer 2. + + +/**************************************************************************************************** +* +* Keymap: Default Layer in Qwerty +* +* ,-------------------------------------------------------------------------------------------------------------------. +* | Esc | F1 | F2 | F3 | F4 | F5 | F6 | F8 | F9 | F10 | F12 | PSCR | SLCK | PAUS | FN0 | BOOT | +* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------| +* | =+ | 1! | 2@ | 3# | 4$ | 5% | | 6^ | 7& | 8* | 9( | 0) | -_ | +* |--------+------+------+------+------+------| +------+------+------+------+------+--------| +* | Tab | Q | W | E | R | T | | Y | U | I | O | P | \| | +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* | Caps | A | S | D | F | G | | H | J | K | L | ;: | '" | +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* | Shift | Z | X | C | V | B | | N | M | ,. | .> | /? | Shift | +* `--------+------+------+------+------+------- `------+------+------+------+------+--------' +* | `~ | INS | Left | Right| | Up | Down | [{ | ]} | +* `---------------------------' `---------------------------' +* ,-------------. ,-------------. +* | Ctrl | Alt | | Gui | Ctrl | +* ,------|------|------| |------+------+------. +* | | | Home | | PgUp | | | +* | BkSp | Del |------| |------|Return| Space| +* | | | End | | PgDn | | | +* `--------------------' `--------------------' +*/ + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[QWERTY] = KEYMAP( + KC_ESC, KC_F1 ,KC_F2 ,KC_F3 ,KC_F4 ,KC_F5 ,KC_F6 ,KC_F7 ,KC_F8, + KC_EQL, KC_1 ,KC_2 ,KC_3 ,KC_4 ,KC_5 , + KC_TAB, KC_Q ,KC_W ,KC_E ,KC_R ,KC_T , + KC_CAPS,KC_A ,KC_S ,KC_D ,KC_F ,KC_G , + KC_LSFT,KC_Z ,KC_X ,KC_C ,KC_V ,KC_B , + KC_GRV ,KC_INS ,KC_LEFT,KC_RGHT, + KC_LCTL,KC_LALT, + KC_HOME, + KC_BSPC,KC_DEL ,KC_END , + KC_F9 ,KC_F10 ,KC_F11 ,KC_F12 ,KC_PSCR ,KC_SLCK ,KC_PAUS, KC_FN0, KC_1, + KC_6 ,KC_7 ,KC_8 ,KC_9 ,KC_0 ,KC_MINS, + KC_Y ,KC_U ,KC_I ,KC_O ,KC_P ,KC_BSLS, + KC_H ,KC_J ,KC_K ,KC_L ,KC_SCLN,KC_QUOT, + KC_N ,KC_M ,KC_COMM,KC_DOT ,KC_SLSH,KC_RSFT, + KC_UP ,KC_DOWN,KC_LBRC,KC_RBRC, + KC_RGUI,KC_RCTL, + KC_PGUP, + KC_PGDN,KC_ENTER ,KC_SPC + ), +[SYMB] = KEYMAP( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_FN0, RESET, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS + ) +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_TOGGLE(SYMB) , // FN1 - Momentary Layer 1 (Symbols) + + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; + + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/kinesis/keymaps/default/readme.md b/keyboards/kinesis/keymaps/default/readme.md new file mode 100644 index 000000000..da033be1e --- /dev/null +++ b/keyboards/kinesis/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for kinesis-advantage diff --git a/keyboards/kinesis/keymaps/programmer/Makefile b/keyboards/kinesis/keymaps/programmer/Makefile new file mode 100644 index 000000000..9d3df5964 --- /dev/null +++ b/keyboards/kinesis/keymaps/programmer/Makefile @@ -0,0 +1,21 @@ +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/kinesis/keymaps/programmer/config.h b/keyboards/kinesis/keymaps/programmer/config.h new file mode 100644 index 000000000..8893d122e --- /dev/null +++ b/keyboards/kinesis/keymaps/programmer/config.h @@ -0,0 +1,8 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +// place overrides here + +#endif diff --git a/keyboards/kinesis/keymaps/programmer/keymap.c b/keyboards/kinesis/keymaps/programmer/keymap.c new file mode 100644 index 000000000..83fb7bd5f --- /dev/null +++ b/keyboards/kinesis/keymaps/programmer/keymap.c @@ -0,0 +1,245 @@ +#include "kinesis.h" +#include "action_layer.h" +#include "mousekey.h" + +#define QWERTY 0 // Base qerty +#define SYMB 1// Symbol layer +#define MOUSE 2// + + + + +/* Macros */ +enum { + NONE = 0, + // Diagonal mouse movement + A_MUL, + A_MUR, + A_MDL, + A_MDR, +}; + + +// Borrowing very heavily from +// https://github.com/alvicstep/tmk_keyboard +/**************************************************************************************************** +* +* Keymap: Default Layer in Qwerty +* +* ,-------------------------------------------------------------------------------------------------------------------. +* | Esc | F1 | F2 | F3 | F4 | F5 | F6 | F8 | F9 | F10 | F12 | FN0 | FN1 | FN2 | | bOOT | +* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------| +* | =+ | 1! | 2@ | 3# | 4$ | 5% | | 6^ | 7& | 8* | 9( | 0) | -_ | +* |--------+------+------+------+------+------| +------+------+------+------+------+--------| +* | Tab | Q | W | E | R | T | | Y | U | I | O | P | \| | +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* |MouseFN1| A | S | D | F | G | | H | J | K | L | ;: | '" | +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* | Shift | Z | X | C | V | B | | N | M | ,. | .> | /? | Shift | +* `--------+------+------+------+------+------- `------+------+------+------+------+--------' +* | `~ | ESC |MOUSE1|MOUSE2| | [{ | ]} | ESC | GUI | +* `---------------------------' `---------------------------' +* ,-------------. ,-------------. +* | Ctrl | Alt | | Gui | Ctrl | +* ,------|------|------| |------+------+------. +* | | | Home | | PgUp | | | +* | BkSp | Del |------| |------|Return| Space| +* | | | End | | PgDn | | | +* `--------------------' `--------------------' +*/ + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[QWERTY] = KEYMAP( + KC_ESC, KC_F1 ,KC_F2 ,KC_F3 ,KC_F4 ,KC_F5 ,KC_F6 ,KC_F7 ,KC_F8, + KC_EQL, KC_1 ,KC_2 ,KC_3 ,KC_4 ,KC_5 , + KC_TAB, KC_Q ,KC_W ,KC_E ,KC_R ,KC_T , + KC_FN1 ,KC_A ,KC_S ,KC_D ,KC_F ,KC_G , + KC_LSFT,KC_Z ,KC_X ,KC_C ,KC_V ,KC_B , + KC_GRV ,KC_ESC, KC_BTN1,KC_BTN2, + KC_LCTL,KC_LALT, + KC_HOME, + KC_BSPC,KC_DEL ,KC_FN0 , + KC_F9 ,KC_F10 ,KC_F11 ,KC_F12 ,KC_FN0 ,KC_FN1 ,KC_FN2, KC_NO, RESET, + KC_6 ,KC_7 ,KC_8 ,KC_9 ,KC_0 ,KC_MINS, + KC_Y ,KC_U ,KC_I ,KC_O ,KC_P ,KC_BSLS, + KC_H ,KC_J ,KC_K ,KC_L ,KC_SCLN,KC_QUOT, + KC_N ,KC_M ,KC_COMM,KC_DOT ,KC_SLSH,KC_RSFT, + KC_LBRC,KC_RBRC, KC_ESC, KC_RGUI, + KC_RGUI,KC_RCTL, + KC_PGUP, + KC_PGDN,KC_ENTER ,KC_SPC + ), +[SYMB] = KEYMAP( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_FN0, KC_2, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS + ), +/* Keymap: Movement and function layer +* +* ,-------------------------------------------------------------------------------------------------------------------. +* | Caps | F1 | F2 | F3 | F4 | F5 | F6 | F8 | F9 | F10 | F12 | FN0 | FN1 | FN2 | Tada | bOOT | +* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------| +* | =+ | ! | @ | # | $ | % | | ^ | & | * | ( | ) |MS Fast | +* |--------+------+------+------+------+------| +------+------+------+------+------+--------| +* | Tab | | | Up | |PgUp | | MwU |MS_UL | MS_U |MS_UR | | Ms Norm| +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* |MouseFN1| C^A | Left | Down |Right | C^E | | | MS_L |Mouse1| MS_R | |MS Slow | +* |--------+------+------+------+------+------| |------+------+------+------+------+--------| +* | | GuiZ | GUI X| GUI C| GUI_V|PgDown| | MWD | MDown|MS Dwn|MS_DR | ? | | +* `--------+------+------+------+------+------- `------+------+------+------+------+--------' +* | `~ | ESC | < | > | | { | } | ESC | | +* `---------------------------' `---------------------------' +* ,-------------. ,-------------. +* | Ctrl | Alt | | Gui | Ctrl | +* ,------|------|------| |------+------+------. +* | | | Home | | PgUp | | | +* | BkSp | Del |------| |------|Mouse1|Mouse2| +* | | | End | | PgDn |LClick|Rclick| +* `--------------------' `--------------------' +*/ + + +[MOUSE] = KEYMAP( + KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_EXLM ,KC_AT, KC_HASH, KC_DLR ,KC_PERC , + KC_TRNS, KC_NO, KC_NO, KC_UP, KC_NO, KC_PGUP, + KC_FN1, LCTL(KC_A),KC_LEFT, KC_DOWN, KC_RIGHT, LCTL(KC_E), + KC_TRNS, LGUI(KC_Z),LGUI(KC_X),LGUI(KC_C),LGUI(KC_V),KC_PGDN, + KC_TRNS, KC_TRNS, KC_LABK, KC_RABK, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_FN0,RESET, + KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_ACL2, + KC_WH_U, M(A_MUL), KC_MS_U, M(A_MUR), KC_NO, KC_ACL1, + KC_NO, KC_MS_L, KC_MS_D, KC_MS_R, KC_NO, KC_ACL0, + KC_WH_D, M(A_MDL), KC_MS_D, M(A_MDR), KC_TRNS, KC_TRNS, + KC_LCBR, KC_RCBR, KC_ESC, KC_TRNS, + KC_TRNS, KC_TRNS, + KC_TRNS, + KC_TRNS, KC_BTN1, KC_BTN2 + ), + + +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_TOGGLE(MOUSE) , // FN1 - Momentary Layer 1 (Symbols) + [1] = ACTION_LAYER_TOGGLE(MOUSE) , // FN1 - Momentary Layer 1 (Symbols) + [2] = ACTION_LAYER_TAP_TOGGLE(SYMB) , // FN1 - Momentary Layer 1 (Symbols) + + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + + // from algernon's ErgoDox EZ layout, + case A_MUL: + if (record->event.pressed) { + mousekey_on(KC_MS_UP); + mousekey_on(KC_MS_LEFT); + } else { + mousekey_off(KC_MS_UP); + mousekey_off(KC_MS_LEFT); + } + mousekey_send(); + break; + + case A_MUR: + if (record->event.pressed) { + mousekey_on(KC_MS_UP); + mousekey_on(KC_MS_RIGHT); + } else { + mousekey_off(KC_MS_UP); + mousekey_off(KC_MS_RIGHT); + } + mousekey_send(); + break; + + case A_MDL: + if (record->event.pressed) { + mousekey_on(KC_MS_DOWN); + mousekey_on(KC_MS_LEFT); + } else { + mousekey_off(KC_MS_DOWN); + mousekey_off(KC_MS_LEFT); + } + mousekey_send(); + break; + + case A_MDR: + if (record->event.pressed) { + mousekey_on(KC_MS_DOWN); + mousekey_on(KC_MS_RIGHT); + } else { + mousekey_off(KC_MS_DOWN); + mousekey_off(KC_MS_RIGHT); + } + mousekey_send(); + break; + } + return MACRO_NONE; +}; + + +void matrix_init_user(void) { + + +} + +void matrix_scan_user(void) { + int8_t layer = biton32(layer_state); + + switch (layer) { + case 1: + all_led_off(); + break; + case 2: + if (!(host_keyboard_leds() & (1 << USB_LED_CAPS_LOCK))) { + all_led_off(); + caps_lock_led_on(); + } + break; + case 0: + all_led_off(); + num_lock_led_on(); + break; + default: + break; + } + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/kinesis/keymaps/programmer/readme.md b/keyboards/kinesis/keymaps/programmer/readme.md new file mode 100644 index 000000000..76356a687 --- /dev/null +++ b/keyboards/kinesis/keymaps/programmer/readme.md @@ -0,0 +1,2 @@ +# a programmer friendly keymap for the kinesis-advantage +# not really baked yet. diff --git a/keyboards/kinesis/kinesis.c b/keyboards/kinesis/kinesis.c new file mode 100644 index 000000000..1fee90e6f --- /dev/null +++ b/keyboards/kinesis/kinesis.c @@ -0,0 +1,106 @@ +#include "kinesis.h" + +// begin section origin https://github.com/alvicstep/tmk_keyboard + + +void all_led_off(void) +{ + PORTD = 0b11111111; +} + +void all_led_on(void) +{ + PORTD = 0b00000000; +} +void num_lock_led_on(void) +{ + PORTD = 0b11101111; +} + +void caps_lock_led_on(void) +{ + PORTD = 0b01111111; +} + +void scroll_lock_led_on(void) +{ + PORTD = 0b11011111; +} +void keypad_led_on(void) +{ + PORTD = 0b10111111; +} +void blink_all_leds(void) +{ + all_led_on(); + _delay_ms(500); + + all_led_off(); + _delay_ms(100); + + caps_lock_led_on(); + _delay_ms(100); + + num_lock_led_on(); + _delay_ms(100); + + scroll_lock_led_on(); + _delay_ms(100); + + keypad_led_on(); + _delay_ms(100); + + //back + + scroll_lock_led_on(); + _delay_ms(100); + + num_lock_led_on(); + _delay_ms(100); + + caps_lock_led_on(); + _delay_ms(100); + + all_led_off(); +} + +// End section origin https://github.com/alvicstep/tmk_keyboard + + void matrix_init_kb(void) { + blink_all_leds(); + matrix_init_user(); +} + + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + +//Copyright 2014 Warren Janssens <warren.janssens@gmail.com> + uint8_t leds = 0xF0; + if (usb_led & 1 << USB_LED_NUM_LOCK) + leds &= ~0x10; + if (usb_led & 1 << USB_LED_CAPS_LOCK) + leds &= ~0x80; + if (usb_led & 1 << USB_LED_SCROLL_LOCK) + leds &= ~0x20; + PORTD = (PORTD & 0x0F) | leds; + + led_set_user(usb_led); + +} + + diff --git a/keyboards/kinesis/kinesis.h b/keyboards/kinesis/kinesis.h new file mode 100644 index 000000000..c04fbda15 --- /dev/null +++ b/keyboards/kinesis/kinesis.h @@ -0,0 +1,67 @@ +#ifndef KINESIS_H +#define KINESIS_H + +#include "quantum.h" + + +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array + +#define KEYMAP( \ + k02,k22,k12,k01,k21,k11,k00,k20,k10, \ + k80,k70,k60,k50,k40,k30, \ + k81,k71,k61,k51,k41,k31, \ + k82,k72,k62,k52,k42,k32, \ + k83,k73,k63,k53,k43,k33, \ + k74,k64,k54,k34, \ + k36,k35, \ + k55, \ + k56,k46,k75, \ + k03,k23,k13,k04,k24,k14,k05,k85,k84, \ + k94,kA4,kB4,kD4,kE4,kF4, \ + k95,kA5,kB5,kD5,kE5,kF5, \ + k96,kA6,kB6,kD6,kE6,kF6, \ + k97,kA7,kB7,kD7,kE7,kF7, \ + k93,kB3,kD3,kE3, \ + k47,k66, \ + k67, \ + k87,k76,k86 \ +) { \ + { k00, k01, k02, k03, k04, k05, KC_NO, KC_NO }, \ + { k10, k11, k12, k13, k14, KC_NO, KC_NO, KC_NO }, \ + { k20, k21, k22, k23, k24, KC_NO, KC_NO, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36, KC_NO }, \ + { k40, k41, k42, k43, KC_NO, KC_NO, k46, k47 }, \ + { k50, k51, k52, k53, k54, k55, k56, KC_NO }, \ + { k60, k61, k62, k63, k64, KC_NO, k66, k67 }, \ + { k70, k71, k72, k73, k74, k75, k76, KC_NO }, \ + { k80, k81, k82, k83, KC_NO ,KC_NO, k86, k87}, \ + { KC_NO, KC_NO ,KC_NO ,k93, k94, k95, k96, k97}, \ + { KC_NO, KC_NO ,KC_NO ,KC_NO, kA4, kA5, kA6, kA7}, \ + { KC_NO, KC_NO ,KC_NO ,kB3, kB4, kB5, kB6, kB7}, \ + { KC_NO, KC_NO ,KC_NO ,KC_NO, KC_NO, KC_NO, k84, k85}, \ + { KC_NO, KC_NO ,KC_NO ,kD3, kD4, kD5, kD6, kD7}, \ + { KC_NO, KC_NO ,KC_NO ,kE3, kE4, kE5, kE6, kE7}, \ + { KC_NO, KC_NO ,KC_NO ,KC_NO, kF4, kF5, kF6, kF7} \ +} + + +/* 4y0 A 4y1 B 4y2 4y3 D 4y4 E 4y5 F 4y6 G 4y7 H 5y0 I 5y1 J 5y2 K 5y3 L 5y4 M 5y5 N 5y6 O 5y7 P */ + +/* + 0 1 2 3 4 5 6 7 8 9 A B C D E F + A B C D E F G H I J K L M N O P + 4y0 4y1 4y2 4y3 4y4 4y5 4y6 4y7 5y0 5y1 5y2 5y3 5y4 5y5 5y6 5y7 + r0 r1 r2 r3 r4 r5 r6 r7 r8 r9 r10 r11 r12 r13 r14 r15 +0 PB0 21 c0 f6 f8 f7 5 4 3 2 1 =+ +1 PB1 22 c1 f3 f5 f4 t r e w q TAB +2 PB2 23 c2 ESC f2 f1 g f d s a CL +3 PB3 24 c3 f9 f11 f10 b v c x z LS UP DN [{ ]} +4 PB4 25 c4 f12 SL PS RT LT §± `~ 6 7 8 9 0 -_ +5 PB5 26 c5 PB PGM KPD LA HM END y u i o p \ +6 PB6 27 c6 LC DEL BS RC ENT SP h j k l ;: '" +7 PB7 28 c7 RA PU PD n m ,< .> /? RS +*/ + + +#endif diff --git a/keyboards/kinesis/matrix.c b/keyboards/kinesis/matrix.c new file mode 100644 index 000000000..cb0d5ad7d --- /dev/null +++ b/keyboards/kinesis/matrix.c @@ -0,0 +1,228 @@ +/* +Copyright 2014 Warren Janssens <warren.janssens@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +/* + * scan matrix + */ +#include <stdint.h> +#include <stdbool.h> +#include <avr/io.h> +#include <util/delay.h> +#include "action_layer.h" +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" +#include "led.h" +#include "config.h" + +#ifndef DEBOUNCE +# define DEBOUNCE 5 +#endif +static uint8_t debouncing = DEBOUNCE; + +/* matrix state(1:on, 0:off) */ +static uint8_t matrix[MATRIX_ROWS]; +static uint8_t matrix_debouncing[MATRIX_ROWS]; + +static matrix_row_t read_row(uint8_t row); +static void unselect_rows(void); +static void select_rows(uint8_t row); + +__attribute__ ((weak)) +void matrix_init_quantum(void) { + matrix_init_kb(); +} + +__attribute__ ((weak)) +void matrix_scan_quantum(void) { + matrix_scan_kb(); +} + +__attribute__ ((weak)) +void matrix_init_kb(void) { + matrix_init_user(); +} + +__attribute__ ((weak)) +void matrix_scan_kb(void) { + matrix_scan_user(); +} + +__attribute__ ((weak)) +void matrix_init_user(void) { +} + +__attribute__ ((weak)) +void matrix_scan_user(void) { +} + +inline +uint8_t matrix_rows(void) +{ + return MATRIX_ROWS; +} + + +inline +uint8_t matrix_cols(void) +{ + return MATRIX_COLS; +} + +void matrix_init(void) +{ + //debug_enable = true; + + //dprint("matrix_init"); dprintln(); + // output high (leds) + DDRD = 0xFF; + PORTD = 0xFF; + + // output low (multiplexers) + DDRF = 0xFF; + PORTF = 0x00; + + // input with pullup (matrix) + DDRB = 0x00; + PORTB = 0xFF; + + // input with pullup (program and keypad buttons) + DDRC = 0x00; + PORTC = 0xFF; + + // initialize row and col + unselect_rows(); + + // initialize matrix state: all keys off + for (uint8_t i=0; i < MATRIX_ROWS; i++) { + matrix[i] = 0; + matrix_debouncing[i] = 0; + } + +} + +uint8_t matrix_scan(void) +{ + + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + select_rows(i); + uint8_t row = read_row(i); + if (matrix_debouncing[i] != row) { + matrix_debouncing[i] = row; + if (debouncing) { + debug("bounce!: "); debug_hex(debouncing); debug("\n"); + } + debouncing = DEBOUNCE; + } + unselect_rows(); + } + + if (debouncing) { + if (--debouncing) { + _delay_ms(1); + } else { + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + matrix[i] = matrix_debouncing[i]; + } + } + } + matrix_scan_quantum(); + return 1; +} + +bool matrix_is_modified(void) +{ + if (debouncing) return false; + return true; +} + +inline +bool matrix_is_on(uint8_t row, uint8_t col) +{ + return (matrix[row] & ((matrix_row_t)1<<col)); +} + +inline +matrix_row_t matrix_get_row(uint8_t row) +{ + return matrix[row]; +} + +void matrix_print(void) +{ + print("\nr/c 01234567\n"); + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + phex(row); print(": "); + pbin_reverse(matrix_get_row(row)); + print("\n"); + } +} + +uint8_t matrix_key_count(void) +{ + uint8_t count = 0; + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + count += bitpop16(matrix[i]); + } + return count; +} + +static matrix_row_t read_row(uint8_t row) +{ + _delay_us(30); // without this wait read unstable value. + + //keypad and program buttons + if (row == 12) + { + return ~(PINC | 0b00111111); + } + return ~PINB; +} + +static void unselect_rows(void) +{ + // set A,B,C,G to 0 (F4 - F7) + PORTF &= 0x0F; +} + +static void select_rows(uint8_t row) +{ + // set A,B,C,G to row value + PORTF |= row << 4; +} + + +/* Row pin configuration +PF0 A +PF1 B +PF2 C +PF3 G 0 = U4, 1 = U5 + + 4y0 4y1 4y2 4y3 4y4 4y5 4y6 4y7 5y0 5y1 5y2 5y3 5y4 5y5 5y6 5y7 + r1 r2 r3 r4 r5 r6 r7 r8 r9 r10 r11 r12 r13 r14 r15 r16 +PB0 21 c1 f6 f8 f7 5 4 3 2 1 =+ +PB1 22 c2 f3 f5 f4 t r e w q TAB +PB2 23 c3 ESC f2 f1 g f d s a CL +PB3 24 c4 f9 f11 f10 b v c x z LS UP DN [{ ]} +PB4 25 c5 f12 SL PS RT LT §± `~ 6 7 8 9 0 -_ +PB5 26 c6 PB PGM KPD y u i o p \ +PB6 27 c7 LC DL BS RC EN SP h j k l ;: '" +PB7 28 c8 RA PU PD n m ,< .> /? RS + */ + + diff --git a/keyboards/kinesis/readme.md b/keyboards/kinesis/readme.md new file mode 100644 index 000000000..a990f9cb9 --- /dev/null +++ b/keyboards/kinesis/readme.md @@ -0,0 +1,42 @@ +kinesis-advantage keyboard firmware +====================== + +## Kinesis specific information +This is a port of https://github.com/alvicstep/tmk_keyboard, +which is a fork of https://github.com/wjanssens/tmk_keyboard, +which is based on work from https://github.com/chrisandreae/keyboard-firmware + +If you replace the kinesis CPU as described in the doc folder, then this code should allow you to use QMK. +I've tested with a Teensy 2++, remember to change the CPU if you use a 32u4 instead. + +Not yet implemented: +- Kinesis EEProm reading or writing +- Audio - this should be simple if we remove hardcoded pins from audio.h and switch to E7 + + + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/kinesis-advantage folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default + +To build with the default keymap, simply run `make`. + +### Other Keymaps + +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: + +``` +$ make keymap=[default|jack|<name>] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` |
