diff options
Diffstat (limited to 'keyboards')
-rw-r--r-- | keyboards/bface/README.md | 61 | ||||
-rw-r--r-- | keyboards/bface/backlight_ps2avrGB.c | 94 | ||||
-rw-r--r-- | keyboards/bface/backlight_ps2avrGB.h | 35 | ||||
-rw-r--r-- | keyboards/bface/bface.c | 46 | ||||
-rw-r--r-- | keyboards/bface/bface.h | 44 | ||||
-rw-r--r-- | keyboards/bface/config.h | 49 | ||||
-rw-r--r-- | keyboards/bface/i2c.c | 104 | ||||
-rw-r--r-- | keyboards/bface/i2c.h | 25 | ||||
-rw-r--r-- | keyboards/bface/keymaps/default/keymap.c | 49 | ||||
-rw-r--r-- | keyboards/bface/matrix.c | 113 | ||||
-rwxr-xr-x | keyboards/bface/program | 105 | ||||
-rw-r--r-- | keyboards/bface/rules.mk | 47 | ||||
-rw-r--r-- | keyboards/bface/usbconfig.h | 396 | ||||
-rw-r--r-- | keyboards/ps2avrGB/README.md | 1 |
14 files changed, 1169 insertions, 0 deletions
diff --git a/keyboards/bface/README.md b/keyboards/bface/README.md new file mode 100644 index 000000000..f8360aec0 --- /dev/null +++ b/keyboards/bface/README.md @@ -0,0 +1,61 @@ +ps2avrGB keyboard firmware +========================== + +This is a port of the QMK firmware for boards that are based on the +ps2avrGB firmware, like the [ps2avrGB +keyboard](https://www.keyclack.com/product/gb-ps2avrgb/) or the ones sold +by [Winkeyless](http://winkeyless.kr/product/ps2avrgb-parts/). + +Note that this is a complete replacement for the firmware, so you won't be +using Bootmapper Client to change any keyboard settings, since not all the +USB report options are supported. + +## Supported Boards + +Only the [B.mini X2](http://winkeyless.kr/product/b-mini-x2-pcb/) has been +tested so far (since it's the only one I own). But other boards that use +the ps2avrGB firmware should work as well. + +## Installing + +First, install the requirements. These commands are for OSX, but all you +need is the AVR toolchain and `bootloadHID` for flashing: + +``` +$ brew cask install crosspack-avr +$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb +``` + +In order to use the `./program` script, which can reboot the board into +the bootloader, you'll need Python 2 with PyUSB installed: + +``` +$ pip install pyusb +``` + +Then, with the keyboard plugged in, simply run this command from the +`qmk_firmware` directory: + +``` +$ make ps2avrGB-program +``` + +If you prefer, you can just build it and flash the firmware directly with +`bootloadHID` if you boot the board while holding down `L_Ctrl` to keep it +in the bootloader: + +``` +$ make ps2avrGB +$ bootloadHID -r ps2avrGB_default.hex +``` + +## Troubleshooting + +From my experience, it's really hard to brick these boards. But these +tricks have been useful when it got stuck in a weird scenario. + +1. Try plugging the board in while pressing `L_Ctrl`. This will force it + to boot only the bootloader without loading the firmware. Once this is + done, just reflash the board with the original firmware. +2. Sometimes USB hubs can act weird, so try connecting the board directly + to your computer or plugging/unplugging the USB hub. diff --git a/keyboards/bface/backlight_ps2avrGB.c b/keyboards/bface/backlight_ps2avrGB.c new file mode 100644 index 000000000..c0f642840 --- /dev/null +++ b/keyboards/bface/backlight_ps2avrGB.c @@ -0,0 +1,94 @@ +/* Copyright 2017 Sebastian Kaim + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifdef BACKLIGHT_ENABLE + +#include "backlight_ps2avrGB.h" +#define sbi(reg,bit) reg |= (_BV(bit)) +#define cbi(reg,bit) reg &= (~_BV(bit)) +#define PWM10 WGM10 +#define PWM11 WGM11 +#define COM1x1 COM1B1 +#define OCR1x OCR1B + +void backlight_init_ports(void) +{ +#if BACKLIGHT_ON_STATE == 0 + backlight_off(); +#else + backlight_on(); +#endif + + // setup pwm + // this bitmagic is sourced from the original firmware + /*TCCR1B = ((TCCR1B & ~0x07) | 0x03); + TCNT1H = 0; + TCNT1L = 0; + sbi(TIMSK, TOIE1); + OCR1BH = 0; + OCR1BL = 0; + cbi(TCCR1A,PWM11); + sbi(TCCR1A,PWM10); + sbi(TCCR1A,COM1B1); + cbi(TCCR1A,COM1B0);*/ + ICR1 = 0xFFFF; + + TCCR1A = _BV(COM1x1) | _BV(WGM11); // = 0b00001010; + TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001; + + backlight_init(); +} + +void backlight_set(uint8_t level) +{ + if( level == 0 ) { + backlight_off(); + } + else { + backlight_on(); + /*uint8_t pwm = get_pwm_for_brightness(level); + set_backlight_pwm(pwm); + TCCR1A |= _BV(COM1x1); + OCR1x = (level >= 2) ? 0xFFFF : 0x00FF;*/ + } +} + +#define PWM_MAX 0xFF +uint8_t get_pwm_for_brightness(uint8_t level) +{ + // we need to cast up here to allow multiplication with 0xFF. We could also use floats, but this is probably a lot faster. + uint16_t brightness = (uint16_t)level * (uint16_t)PWM_MAX / (uint16_t)BACKLIGHT_LEVELS; + return (uint8_t)brightness; +} + +void backlight_on(void) +{ + //_SFR_IO8(0x12) |= _BV(0x4); + LED_PIN |= BACKLIGHT_PORT_NUM; +} + +void backlight_off(void) +{ + //_SFR_IO8(0x12) &= ~_BV(0x4); + LED_PIN &= ~BACKLIGHT_PORT_NUM; +} + +void set_backlight_pwm(uint8_t level) { + // this does not work (yet) + //OCR1B = level; +} + +#endif // BACKLIGHT_ENABLE diff --git a/keyboards/bface/backlight_ps2avrGB.h b/keyboards/bface/backlight_ps2avrGB.h new file mode 100644 index 000000000..d5ca90399 --- /dev/null +++ b/keyboards/bface/backlight_ps2avrGB.h @@ -0,0 +1,35 @@ +/* Copyright 2017 Sebastian Kaim + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + + +#if defined(__AVR__) +#include <avr/pgmspace.h> +#include <avr/io.h> +#include <avr/interrupt.h> +#endif +#include <stddef.h> +#include <stdlib.h> +#include "backlight.h" + +#ifndef PS2AVRGB_BACKLIGHT_H +#define PS2AVRGB_BACKLIGHT_H + +uint8_t get_pwm_for_brightness(uint8_t level); +void set_backlight_pwm(uint8_t level); +void backlight_on(void); +void backlight_off(void); + +#endif diff --git a/keyboards/bface/bface.c b/keyboards/bface/bface.c new file mode 100644 index 000000000..8422a4a40 --- /dev/null +++ b/keyboards/bface/bface.c @@ -0,0 +1,46 @@ +/* +Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com> +Copyright 2018 Sebastian Kaim <sebb@sebb767.de> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "bface.h" +#include "rgblight.h" + +#include <avr/pgmspace.h> + +#include "action_layer.h" +#include "i2c.h" +#include "quantum.h" + +extern rgblight_config_t rgblight_config; + +void rgblight_set(void) { + if (!rgblight_config.enable) { + for (uint8_t i = 0; i < RGBLED_NUM; i++) { + led[i].r = 0; + led[i].g = 0; + led[i].b = 0; + } + } + + i2c_init(); + i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM); +} + +__attribute__ ((weak)) +void matrix_scan_user(void) { + rgblight_task(); +} diff --git a/keyboards/bface/bface.h b/keyboards/bface/bface.h new file mode 100644 index 000000000..1f1f3393f --- /dev/null +++ b/keyboards/bface/bface.h @@ -0,0 +1,44 @@ +/* +Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com> +Copyright 2017 Sebastian Kaim <sebb@sebb767.de> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef KEYMAP_COMMON_H +#define KEYMAP_COMMON_H + +#include "quantum_keycodes.h" +#include "keycode.h" +#include "action.h" + +#define KEYMAP( \ + K04, K14, K24, K34, K44, K54, K16, KB6, KB7, K17, KA4, KB4, KC4, KE4, \ + K03, K13, K23, K33, K43, K53, K26, KC6, KC7, K27, KA3, KB3, KC3, KD3, \ + K02, K12, K22, K32, K42, K52, K36, KD6, KD7, K37, KA2, KB2, KD2, \ + K01, K11, K21, K31, K41, K51, K46, KE6, KE7, K47, KA1, KB1, \ + K00, K10, K20, K56, K57, KA0, KB0, KC0 \ +){ \ + { K00, K10, K20, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KA0, KB0, KC0, KC_NO, KC_NO }, \ + { K01, K11, K21, K31, K41, K51, KC_NO, KC_NO, KC_NO, KC_NO, KA1, KB1, KC_NO, KC_NO, KC_NO }, \ + { K02, K12, K22, K32, K42, K52, KC_NO, KC_NO, KC_NO, KC_NO, KA2, KB2, KC_NO, KD2, KC_NO }, \ + { K03, K13, K23, K33, K43, K53, KC_NO, KC_NO, KC_NO, KC_NO, KA3, KB3, KC3, KD3, KC_NO }, \ + { K04, K14, K24, K34, K44, K54, KC_NO, KC_NO, KC_NO, KC_NO, KA4, KB4, KC4, KC_NO, KE4 }, \ + { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \ + { KC_NO, K16, K26, K36, K46, K56, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KB6, KC6, KD6, KE6 }, \ + { KC_NO, K17, K27, K37, K47, K57, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KB7, KC7, KD7, KE7 } \ +} + + +#endif diff --git a/keyboards/bface/config.h b/keyboards/bface/config.h new file mode 100644 index 000000000..3d74af4f1 --- /dev/null +++ b/keyboards/bface/config.h @@ -0,0 +1,49 @@ +/* +Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com> +Copyright 2017 Sebastian Kaim <sebastian.kaim@sebb767.de> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#define VENDOR_ID 0x20A0 +#define PRODUCT_ID 0x422D +// You can edit those at usbconfig.h about line 250. These values will +// unforunatly be ignored so far +#define MANUFACTURER winkeyless.kr +#define PRODUCT b.face + +/* matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 15 + +#define RGBLED_NUM 16 +#define RGBLIGHT_ANIMATIONS + +#define NO_UART 1 +#define BOOTLOADHID_BOOTLOADER 1 + +/* key combination for command */ +#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) + +#ifdef BACKLIGHT_ENABLE + // the backlight PWM does not work (yet). Therefore, we only have two backlight levels (on/off) + #define BACKLIGHT_LEVELS 1 + #define LED_PIN PORTD + #define BACKLIGHT_PORT_NUM (1 << 4) +#endif + +#endif diff --git a/keyboards/bface/i2c.c b/keyboards/bface/i2c.c new file mode 100644 index 000000000..c27f3e3d1 --- /dev/null +++ b/keyboards/bface/i2c.c @@ -0,0 +1,104 @@ +/* +Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <avr/io.h> +#include <util/twi.h> + +#include "i2c.h" + +void i2c_set_bitrate(uint16_t bitrate_khz) { + uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz); + if (bitrate_div >= 16) { + bitrate_div = (bitrate_div - 16) / 2; + } + TWBR = bitrate_div; +} + +void i2c_init(void) { + // set pull-up resistors on I2C bus pins + PORTC |= 0b11; + + i2c_set_bitrate(400); + + // enable TWI (two-wire interface) + TWCR |= (1 << TWEN); + + // enable TWI interrupt and slave address ACK + TWCR |= (1 << TWIE); + TWCR |= (1 << TWEA); +} + +uint8_t i2c_start(uint8_t address) { + // reset TWI control register + TWCR = 0; + + // begin transmission and wait for it to end + TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN); + while (!(TWCR & (1<<TWINT))); + + // check if the start condition was successfully transmitted + if ((TWSR & 0xF8) != TW_START) { + return 1; + } + + // transmit address and wait + TWDR = address; + TWCR = (1<<TWINT) | (1<<TWEN); + while (!(TWCR & (1<<TWINT))); + + // check if the device has acknowledged the READ / WRITE mode + uint8_t twst = TW_STATUS & 0xF8; + if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) { + return 1; + } + + return 0; +} + +void i2c_stop(void) { + TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO); +} + +uint8_t i2c_write(uint8_t data) { + TWDR = data; + + // transmit data and wait + TWCR = (1<<TWINT) | (1<<TWEN); + while (!(TWCR & (1<<TWINT))); + + if ((TWSR & 0xF8) != TW_MT_DATA_ACK) { + return 1; + } + + return 0; +} + +uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) { + if (i2c_start(address)) { + return 1; + } + + for (uint16_t i = 0; i < length; i++) { + if (i2c_write(data[i])) { + return 1; + } + } + + i2c_stop(); + + return 0; +} diff --git a/keyboards/bface/i2c.h b/keyboards/bface/i2c.h new file mode 100644 index 000000000..27c9d3d05 --- /dev/null +++ b/keyboards/bface/i2c.h @@ -0,0 +1,25 @@ +/* +Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef __I2C_H__ +#define __I2C_H__ + +void i2c_init(void); +void i2c_set_bitrate(uint16_t bitrate_khz); +uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length); + +#endif diff --git a/keyboards/bface/keymaps/default/keymap.c b/keyboards/bface/keymaps/default/keymap.c new file mode 100644 index 000000000..785ab2e9d --- /dev/null +++ b/keyboards/bface/keymaps/default/keymap.c @@ -0,0 +1,49 @@ +/* +Copyright 2017 Sebastian Kaim <sebastian.kaim@sebb767.de> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "bface.h" +#include "action_layer.h" +#include "rgblight.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = KEYMAP( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS,KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC,KC_RBRC,KC_BSLS, + KC_F1, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT,KC_ENT, + KC_LSFT,KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL,KC_LALT,KC_LGUI, KC_SPC, KC_RALT,KC_RGUI,KC_FN0, KC_RCTL + ), + [1] = KEYMAP( + KC_TRNS,KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,BL_INC, BL_DEC, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, + KC_TRNS,KC_TRNS,RGB_SMOD,KC_TRNS,BL_ON, BL_OFF, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS + ), + /* You can copy this layer as base for a new fn layer * / + [n] = KEYMAP( + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS + ), // */ +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), +}; diff --git a/keyboards/bface/matrix.c b/keyboards/bface/matrix.c new file mode 100644 index 000000000..b3761a63c --- /dev/null +++ b/keyboards/bface/matrix.c @@ -0,0 +1,113 @@ +/* +Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <avr/io.h> +#include <util/delay.h> + +#include "matrix.h" + +#ifndef DEBOUNCE +# define DEBOUNCE 5 +#endif + +static uint8_t debouncing = DEBOUNCE; + +static matrix_row_t matrix[MATRIX_ROWS]; +static matrix_row_t matrix_debouncing[MATRIX_ROWS]; + +void matrix_init(void) { + // all outputs for rows high + DDRB = 0xFF; + PORTB = 0xFF; + // all inputs for columns + DDRA = 0x00; + DDRC &= ~(0x111111<<2); + DDRD &= ~(1<<PIND7); + // all columns are pulled-up + PORTA = 0xFF; + PORTC |= (0b111111<<2); + PORTD |= (1<<PIND7); + + // initialize matrix state: all keys off + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + matrix[row] = 0x00; + matrix_debouncing[row] = 0x00; + } + + // activate backlight + //PORTD |= (1 << 4); + //_SFR_IO8(0x09) |= (1 << 4); //_BV(0x94 & 0xF); + // + // this is the code that *should* be executed in quantum.c + _SFR_IO8(0x12) |= _BV(0x4); +} + +void matrix_set_row_status(uint8_t row) { + DDRB = (1 << row); + PORTB = ~(1 << row); +} + +uint8_t bit_reverse(uint8_t x) { + x = ((x >> 1) & 0x55) | ((x << 1) & 0xaa); + x = ((x >> 2) & 0x33) | ((x << 2) & 0xcc); + x = ((x >> 4) & 0x0f) | ((x << 4) & 0xf0); + return x; +} + +uint8_t matrix_scan(void) { + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + matrix_set_row_status(row); + _delay_us(5); + + matrix_row_t cols = ( + // cols 0..7, PORTA 0 -> 7 + (~PINA) & 0xFF + ) | ( + // cols 8..13, PORTC 7 -> 0 + bit_reverse((~PINC) & 0xFF) << 8 + ) | ( + // col 14, PORTD 7 + ((~PIND) & (1 << PIND7)) << 7 + ); + + if (matrix_debouncing[row] != cols) { + matrix_debouncing[row] = cols; + debouncing = DEBOUNCE; + } + } + + if (debouncing) { + if (--debouncing) { + _delay_ms(1); + } else { + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + matrix[i] = matrix_debouncing[i]; + } + } + } + + matrix_scan_user(); + + return 1; +} + +inline matrix_row_t matrix_get_row(uint8_t row) { + return matrix[row]; +} + +void matrix_print(void) { +} diff --git a/keyboards/bface/program b/keyboards/bface/program new file mode 100755 index 000000000..298e64547 --- /dev/null +++ b/keyboards/bface/program @@ -0,0 +1,105 @@ +#!/usr/bin/env python +# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>, Sebastian Kaim <sebb@sebb767.de> +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + +from __future__ import print_function + +import os +import sys +import time +import usb + + +def checkForKeyboardInNormalMode(): + """Returns a device if a ps2avrGB device in normal made (that is in keyboard mode) or None if it is not found.""" + return usb.core.find(idVendor=0x20A0, idProduct=0x422D) + +def checkForKeyboardInBootloaderMode(): + """Returns True if a ps2avrGB device in bootloader (flashable) mode is found and False otherwise.""" + return (usb.core.find(idVendor=0x16c0, idProduct=0x05df) is not None) + +def flashKeyboard(firmware_file): + """Calls bootloadHID to flash the given file to the device.""" + print('Flashing firmware to device ...') + if os.system('bootloadHID -r "%s"' % firmware_file) == 0: + print('\nDone!') + else: + print('\nbootloadHID returned an error.') + +def printDeviceInfo(dev): + """Prints all infos for a given USB device""" + print('Device Information:') + print(' idVendor: %d (0x%04x)' % (dev.idVendor, dev.idVendor)) + print(' idProduct: %d (0x%04x)' % (dev.idProduct, dev.idProduct)) + print('Manufacturer: %s' % (dev.iManufacturer)) + print('Serial: %s' % (dev.iSerialNumber)) + print('Product: %s' % (dev.iProduct), end='\n\n') + +def sendDeviceToBootloaderMode(dev): + """Tries to send a given ps2avrGB keyboard to bootloader mode to allow flashing.""" + try: + dev.set_configuration() + + request_type = usb.util.build_request_type( + usb.util.CTRL_OUT, + usb.util.CTRL_TYPE_CLASS, + usb.util.CTRL_RECIPIENT_DEVICE) + + USBRQ_HID_SET_REPORT = 0x09 + HID_REPORT_OPTION = 0x0301 + + dev.ctrl_transfer(request_type, USBRQ_HID_SET_REPORT, HID_REPORT_OPTION, 0, [0, 0, 0xFF] + [0] * 5) + except usb.core.USBError: + # for some reason I keep getting USBError, but it works! + pass + + +if len(sys.argv) < 2: + print('Usage: %s <firmware.hex>' % sys.argv[0]) + sys.exit(1) + +kb = checkForKeyboardInNormalMode() + +if kb is not None: + print('Found a keyboad in normal mode. Attempting to send it to bootloader mode ...', end='') + sendDeviceToBootloaderMode(kb) + print(' done.') + print("Hint: If your keyboard can't be set to bootloader mode automatically, plug it in while pressing the bootloader key to do so manually.") + print(" You can find more infos about this here: https://github.com/qmk/qmk_firmware/tree/master/keyboards/ps2avrGB#setting-the-board-to-bootloader-mode") + +attempts = 12 # 60 seconds +found = False +for attempt in range(1, attempts + 1): + print("Searching for keyboard in bootloader mode (%i/%i) ... " % (attempt, attempts), end='') + + if checkForKeyboardInBootloaderMode(): + print('Found', end='\n\n') + flashKeyboard(sys.argv[1]) + found = True + break + else: + print('Nothing.', end='') + + if attempt != attempts: # no need to wait on the last attempt + print(' Sleeping 5 seconds.', end='') + time.sleep(5) + + # print a newline + print() + +if not found: + print("Couldn't find a flashable keyboard. Aborting.") + sys.exit(2) + diff --git a/keyboards/bface/rules.mk b/keyboards/bface/rules.mk new file mode 100644 index 000000000..6fb32ae57 --- /dev/null +++ b/keyboards/bface/rules.mk @@ -0,0 +1,47 @@ +# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com> +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + +# MCU name +MCU = atmega32a +PROTOCOL = VUSB + +# unsupported features for now +NO_UART = yes +NO_SUSPEND_POWER_DOWN = yes + +# processor frequency +F_CPU = 12000000 + +# build options +BOOTMAGIC_ENABLE = yes +MOUSEKEY_ENABLE = yes +EXTRAKEY_ENABLE = yes +CONSOLE_ENABLE = no +COMMAND_ENABLE = yes +BACKLIGHT_ENABLE = yes +BACKLIGHT_CUSTOM_DRIVER = yes +BACKLIGHT_BREATHING = no +RGBLIGHT_ENABLE = yes +RGBLIGHT_CUSTOM_DRIVER = yes + +OPT_DEFS = -DDEBUG_LEVEL=0 +OPT_DEFS += -DBOOTLOADER_SIZE=2048 + +# custom matrix setup +CUSTOM_MATRIX = yes +SRC = matrix.c i2c.c backlight_ps2avrGB.c + +# programming options +PROGRAM_CMD = ./keyboards/bface/program .build/$(TARGET).hex diff --git a/keyboards/bface/usbconfig.h b/keyboards/bface/usbconfig.h new file mode 100644 index 000000000..f87922615 --- /dev/null +++ b/keyboards/bface/usbconfig.h @@ -0,0 +1,396 @@ +/* Name: usbconfig.h + * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers + * Author: Christian Starkjohann + * Creation Date: 2005-04-01 + * Tabsize: 4 + * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) + * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ + */ + +#ifndef __usbconfig_h_included__ +#define __usbconfig_h_included__ + +#include "config.h" + +/* +General Description: +This file is an example configuration (with inline documentation) for the USB +driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is +also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may +wire the lines to any other port, as long as D+ is also wired to INT0 (or any +other hardware interrupt, as long as it is the highest level interrupt, see +section at the end of this file). +*/ + +/* ---------------------------- Hardware Config ---------------------------- */ + +#define USB_CFG_IOPORTNAME D +/* This is the port where the USB bus is connected. When you configure it to + * "B", the registers PORTB, PINB and DDRB will be used. + */ +#define USB_CFG_DMINUS_BIT 3 +/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. + * This may be any bit in the port. + */ +#define USB_CFG_DPLUS_BIT 2 +/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. + * This may be any bit in the port. Please note that D+ must also be connected + * to interrupt pin INT0! [You can also use other interrupts, see section + * "Optional MCU Description" below, or you can connect D- to the interrupt, as + * it is required if you use the USB_COUNT_SOF feature. If you use D- for the + * interrupt, the USB interrupt will also be triggered at Start-Of-Frame + * markers every millisecond.] + */ +#define USB_CFG_CLOCK_KHZ (F_CPU/1000) +/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, + * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code + * require no crystal, they tolerate +/- 1% deviation from the nominal + * frequency. All other rates require a precision of 2000 ppm and thus a + * crystal! + * Since F_CPU should be defined to your actual clock rate anyway, you should + * not need to modify this setting. + */ +#define USB_CFG_CHECK_CRC 0 +/* Define this to 1 if you want that the driver checks integrity of incoming + * data packets (CRC checks). CRC checks cost quite a bit of code size and are + * currently only available for 18 MHz crystal clock. You must choose + * USB_CFG_CLOCK_KHZ = 18000 if you enable this option. + */ + +/* ----------------------- Optional Hardware Config ------------------------ */ + +/* #define USB_CFG_PULLUP_IOPORTNAME D */ +/* If you connect the 1.5k pullup resistor from D- to a port pin instead of + * V+, you can connect and disconnect the device from firmware by calling + * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). + * This constant defines the port on which the pullup resistor is connected. + */ +/* #define USB_CFG_PULLUP_BIT 4 */ +/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined + * above) where the 1.5k pullup resistor is connected. See description + * above for details. + */ + +/* --------------------------- Functional Range ---------------------------- */ + +#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 +/* Define this to 1 if you want to compile a version with two endpoints: The + * default control endpoint 0 and an interrupt-in endpoint (any other endpoint + * number). + */ +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 +/* Define this to 1 if you want to compile a version with three endpoints: The + * default control endpoint 0, an interrupt-in endpoint 3 (or the number + * configured below) and a catch-all default interrupt-in endpoint as above. + * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. + */ +#define USB_CFG_EP3_NUMBER 3 +/* If the so-called endpoint 3 is used, it can now be configured to any other + * endpoint number (except 0) with this macro. Default if undefined is 3. + */ +/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ +/* The above macro defines the startup condition for data toggling on the + * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. + * Since the token is toggled BEFORE sending any data, the first packet is + * sent with the oposite value of this configuration! + */ +#define USB_CFG_IMPLEMENT_HALT 0 +/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature + * for endpoint 1 (interrupt endpoint). Although you may not need this feature, + * it is required by the standard. We have made it a config option because it + * bloats the code considerably. + */ +#define USB_CFG_SUPPRESS_INTR_CODE 0 +/* Define this to 1 if you want to declare interrupt-in endpoints, but don't + * want to send any data over them. If this macro is defined to 1, functions + * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if + * you need the interrupt-in endpoints in order to comply to an interface + * (e.g. HID), but never want to send any data. This option saves a couple + * of bytes in flash memory and the transmit buffers in RAM. + */ +#define USB_CFG_INTR_POLL_INTERVAL 1 +/* If you compile a version with endpoint 1 (interrupt-in), this is the poll + * interval. The value is in milliseconds and must not be less than 10 ms for + * low speed devices. + */ +#define USB_CFG_IS_SELF_POWERED 0 +/* Define this to 1 if the device has its own power supply. Set it to 0 if the + * device is powered from the USB bus. + */ +#define USB_CFG_MAX_BUS_POWER 500 +/* Set this variable to the maximum USB bus power consumption of your device. + * The value is in milliamperes. [It will be divided by two since USB + * communicates power requirements in units of 2 mA.] + */ +#define USB_CFG_IMPLEMENT_FN_WRITE 1 +/* Set this to 1 if you want usbFunctionWrite() to be called for control-out + * transfers. Set it to 0 if you don't need it and want to save a couple of + * bytes. + */ +#define USB_CFG_IMPLEMENT_FN_READ 0 +/* Set this to 1 if you need to send control replies which are generated + * "on the fly" when usbFunctionRead() is called. If you only want to send + * data from a static buffer, set it to 0 and return the data from + * usbFunctionSetup(). This saves a couple of bytes. + */ +#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 +/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. + * You must implement the function usbFunctionWriteOut() which receives all + * interrupt/bulk data sent to any endpoint other than 0. The endpoint number + * can be found in 'usbRxToken'. + */ +#define USB_CFG_HAVE_FLOWCONTROL 0 +/* Define this to 1 if you want flowcontrol over USB data. See the definition + * of the macros usbDisableAllRequests() and usbEnableAllRequests() in + * usbdrv.h. + */ +#define USB_CFG_DRIVER_FLASH_PAGE 0 +/* If the device has more than 64 kBytes of flash, define this to the 64 k page + * where the driver's constants (descriptors) are located. Or in other words: + * Define this to 1 for boot loaders on the ATMega128. + */ +#define USB_CFG_LONG_TRANSFERS 0 +/* Define this to 1 if you want to send/receive blocks of more than 254 bytes + * in a single control-in or control-out transfer. Note that the capability + * for long transfers increases the driver size. + */ +/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ +/* This macro is a hook if you want to do unconventional things. If it is + * defined, it's inserted at the beginning of received message processing. + * If you eat the received message and don't want default processing to + * proceed, do a return after doing your things. One possible application + * (besides debugging) is to flash a status LED on each packet. + */ +/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ +/* This macro is a hook if you need to know when an USB RESET occurs. It has + * one parameter which distinguishes between the start of RESET state and its + * end. + */ +/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ +/* This macro (if defined) is executed when a USB SET_ADDRESS request was + * received. + */ +#define USB_COUNT_SOF 1 +/* define this macro to 1 if you need the global variable "usbSofCount" which + * counts SOF packets. This feature requires that the hardware interrupt is + * connected to D- instead of D+. + */ +/* #ifdef __ASSEMBLER__ + * macro myAssemblerMacro + * in YL, TCNT0 + * sts timer0Snapshot, YL + * endm + * #endif + * #define USB_SOF_HOOK myAssemblerMacro + * This macro (if defined) is executed in the assembler module when a + * Start Of Frame condition is detected. It is recommended to define it to + * the name of an assembler macro which is defined here as well so that more + * than one assembler instruction can be used. The macro may use the register + * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages + * immediately after an SOF pulse may be lost and must be retried by the host. + * What can you do with this hook? Since the SOF signal occurs exactly every + * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in + * designs running on the internal RC oscillator. + * Please note that Start Of Frame detection works only if D- is wired to the + * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! + */ +#define USB_CFG_CHECK_DATA_TOGGLING 0 +/* define this macro to 1 if you want to filter out duplicate data packets + * sent by the host. Duplicates occur only as a consequence of communication + * errors, when the host does not receive an ACK. Please note that you need to + * implement the filtering yourself in usbFunctionWriteOut() and + * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable + * for each control- and out-endpoint to check for duplicate packets. + */ +#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 +/* define this macro to 1 if you want the function usbMeasureFrameLength() + * compiled in. This function can be used to calibrate the AVR's RC oscillator. + */ +#define USB_USE_FAST_CRC 0 +/* The assembler module has two implementations for the CRC algorithm. One is + * faster, the other is smaller. This CRC routine is only used for transmitted + * messages where timing is not critical. The faster routine needs 31 cycles + * per byte while the smaller one needs 61 to 69 cycles. The faster routine + * may be worth the 32 bytes bigger code size if you transmit lots of data and + * run the AVR close to its limit. + */ + +/* -------------------------- Device Description --------------------------- */ + +#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) +/* USB vendor ID for the device, low byte first. If you have registered your + * own Vendor ID, define it here. Otherwise you may use one of obdev's free + * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) +/* This is the ID of the product, low byte first. It is interpreted in the + * scope of the vendor ID. If you have registered your own VID with usb.org + * or if you have licensed a PID from somebody else, define it here. Otherwise + * you may use one of obdev's free shared VID/PID pairs. See the file + * USB-IDs-for-free.txt for details! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_VERSION 0x00, 0x02 +/* Version number of the device: Minor number first, then major number. + */ +#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r' +#define USB_CFG_VENDOR_NAME_LEN 13 +/* These two values define the vendor name returned by the USB device. The name + * must be given as a list of characters under single quotes. The characters + * are interpreted as Unicode (UTF-16) entities. + * If you don't want a vendor name string, undefine these macros. + * ALWAYS define a vendor name containing your Internet domain name if you use + * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for + * details. + */ +#define USB_CFG_DEVICE_NAME 'b', '.', 'f', 'a', 'c', 'e' +#define USB_CFG_DEVICE_NAME_LEN 6 +/* Same as above for the device name. If you don't want a device name, undefine + * the macros. See the file USB-IDs-for-free.txt before you assign a name if + * you use a shared VID/PID. + */ +/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */ +/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */ +/* Same as above for the serial number. If you don't want a serial number, + * undefine the macros. + * It may be useful to provide the serial number through other means than at + * compile time. See the section about descriptor properties below for how + * to fine tune control over USB descriptors such as the string descriptor + * for the serial number. + */ +#define USB_CFG_DEVICE_CLASS 0 +#define USB_CFG_DEVICE_SUBCLASS 0 +/* See USB specification if you want to conform to an existing device class. + * Class 0xff is "vendor specific". + */ +#define USB_CFG_INTERFACE_CLASS 3 /* HID */ +#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ +#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ +/* See USB specification if you want to conform to an existing device class or + * protocol. The following classes must be set at interface level: + * HID class is 3, no subclass and protocol required (but may be useful!) + * CDC class is 2, use subclass 2 and protocol 1 for ACM + */ +#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 +/* Define this to the length of the HID report descriptor, if you implement + * an HID device. Otherwise don't define it or define it to 0. + * If you use this define, you must add a PROGMEM character array named + * "usbHidReportDescriptor" to your code which contains the report descriptor. + * Don't forget to keep the array and this define in sync! + */ + +/* #define USB_PUBLIC static */ +/* Use the define above if you #include usbdrv.c instead of linking against it. + * This technique saves a couple of bytes in flash memory. + */ + +/* ------------------- Fine Control over USB Descriptors ------------------- */ +/* If you don't want to use the driver's default USB descriptors, you can + * provide our own. These can be provided as (1) fixed length static data in + * flash memory, (2) fixed length static data in RAM or (3) dynamically at + * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more + * information about this function. + * Descriptor handling is configured through the descriptor's properties. If + * no properties are defined or if they are 0, the default descriptor is used. + * Possible properties are: + * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched + * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is + * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if + * you want RAM pointers. + * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found + * in static memory is in RAM, not in flash memory. + * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), + * the driver must know the descriptor's length. The descriptor itself is + * found at the address of a well known identifier (see below). + * List of static descriptor names (must be declared PROGMEM if in flash): + * char usbDescriptorDevice[]; + * char usbDescriptorConfiguration[]; + * char usbDescriptorHidReport[]; + * char usbDescriptorString0[]; + * int usbDescriptorStringVendor[]; + * int usbDescriptorStringDevice[]; + * int usbDescriptorStringSerialNumber[]; + * Other descriptors can't be provided statically, they must be provided + * dynamically at runtime. + * + * Descriptor properties are or-ed or added together, e.g.: + * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) + * + * The following descriptors are defined: + * USB_CFG_DESCR_PROPS_DEVICE + * USB_CFG_DESCR_PROPS_CONFIGURATION + * USB_CFG_DESCR_PROPS_STRINGS + * USB_CFG_DESCR_PROPS_STRING_0 + * USB_CFG_DESCR_PROPS_STRING_VENDOR + * USB_CFG_DESCR_PROPS_STRING_PRODUCT + * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER + * USB_CFG_DESCR_PROPS_HID + * USB_CFG_DESCR_PROPS_HID_REPORT + * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) + * + * Note about string descriptors: String descriptors are not just strings, they + * are Unicode strings prefixed with a 2 byte header. Example: + * int serialNumberDescriptor[] = { + * USB_STRING_DESCRIPTOR_HEADER(6), + * 'S', 'e', 'r', 'i', 'a', 'l' + * }; + */ + +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID 0 +#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 + +#define usbMsgPtr_t unsigned short +/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to + * a scalar type here because gcc generates slightly shorter code for scalar + * arithmetics than for pointer arithmetics. Remove this define for backward + * type compatibility or define it to an 8 bit type if you use data in RAM only + * and all RAM is below 256 bytes (tiny memory model in IAR CC). + */ + +/* ----------------------- Optional MCU Description ------------------------ */ + +/* The following configurations have working defaults in usbdrv.h. You + * usually don't need to set them explicitly. Only if you want to run + * the driver on a device which is not yet supported or with a compiler + * which is not fully supported (such as IAR C) or if you use a differnt + * interrupt than INT0, you may have to define some of these. + */ +/* #define USB_INTR_CFG MCUCR */ +/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE GIMSK */ +/* #define USB_INTR_ENABLE_BIT INT0 */ +/* #define USB_INTR_PENDING GIFR */ +/* #define USB_INTR_PENDING_BIT INTF0 */ +/* #define USB_INTR_VECTOR INT0_vect */ + +/* Set INT1 for D- falling edge to count SOF */ +/* #define USB_INTR_CFG EICRA */ +#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE EIMSK */ +#define USB_INTR_ENABLE_BIT INT1 +/* #define USB_INTR_PENDING EIFR */ +#define USB_INTR_PENDING_BIT INTF1 +#define USB_INTR_VECTOR INT1_vect + +#endif /* __usbconfig_h_included__ */ diff --git a/keyboards/ps2avrGB/README.md b/keyboards/ps2avrGB/README.md index 5111be264..8399dff02 100644 --- a/keyboards/ps2avrGB/README.md +++ b/keyboards/ps2avrGB/README.md @@ -17,6 +17,7 @@ compatible with QMK; fully supported boards have their own directory. - [b.fake](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bfake) - [b.mini](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bmini) +- [b.face](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bface) - [pearl](https://github.com/qmk/qmk_firmware/tree/master/keyboards/pearl) ## Installing |