aboutsummaryrefslogtreecommitdiffstats
path: root/keyboard/atomic/Makefile
diff options
context:
space:
mode:
Diffstat (limited to 'keyboard/atomic/Makefile')
-rw-r--r--keyboard/atomic/Makefile73
1 files changed, 0 insertions, 73 deletions
diff --git a/keyboard/atomic/Makefile b/keyboard/atomic/Makefile
deleted file mode 100644
index 08e9205cb..000000000
--- a/keyboard/atomic/Makefile
+++ /dev/null
@@ -1,73 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no # MIDI controls
-AUDIO_ENABLE ?= no # Audio output on port C6
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
- include ../../Makefile
-endif \ No newline at end of file