diff options
58 files changed, 269 insertions, 1481 deletions
diff --git a/keyboards/laptreus/rules.mk b/keyboards/laptreus/rules.mk index 01401ab38..237a6ac8b 100644 --- a/keyboards/laptreus/rules.mk +++ b/keyboards/laptreus/rules.mk @@ -1,46 +1,18 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. +# Processor frequency F_CPU = 8000000 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -BOOTLOADER = catarina - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/launchpad/keymaps/default/rules.mk b/keyboards/launchpad/keymaps/default/rules.mk deleted file mode 100644 index d1fa27f41..000000000 --- a/keyboards/launchpad/keymaps/default/rules.mk +++ /dev/null @@ -1,22 +0,0 @@ - - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - diff --git a/keyboards/launchpad/keymaps/default_rgb/rules.mk b/keyboards/launchpad/keymaps/default_rgb/rules.mk index 164232f33..1e3cebb14 100644 --- a/keyboards/launchpad/keymaps/default_rgb/rules.mk +++ b/keyboards/launchpad/keymaps/default_rgb/rules.mk @@ -1 +1 @@ -RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
\ No newline at end of file +RGBLIGHT_ENABLE = yes diff --git a/keyboards/launchpad/rev1/rules.mk b/keyboards/launchpad/rev1/rules.mk index bafce654a..e69de29bb 100644 --- a/keyboards/launchpad/rev1/rules.mk +++ b/keyboards/launchpad/rev1/rules.mk @@ -1,3 +0,0 @@ -BACKLIGHT_ENABLE = no -RGBLIGHT_ENABLE = no -AUDIO_ENABLE = no
\ No newline at end of file diff --git a/keyboards/launchpad/rules.mk b/keyboards/launchpad/rules.mk index b2c64db7a..59b285cf5 100644 --- a/keyboards/launchpad/rules.mk +++ b/keyboards/launchpad/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -50,8 +19,8 @@ BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = no # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 diff --git a/keyboards/lazydesigners/dimple/rules.mk b/keyboards/lazydesigners/dimple/rules.mk index a818e871c..99e4911af 100644 --- a/keyboards/lazydesigners/dimple/rules.mk +++ b/keyboards/lazydesigners/dimple/rules.mk @@ -1,50 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/lazydesigners/the50/rules.mk b/keyboards/lazydesigners/the50/rules.mk index ae211ec66..561e38a99 100644 --- a/keyboards/lazydesigners/the50/rules.mk +++ b/keyboards/lazydesigners/the50/rules.mk @@ -1,41 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/lazydesigners/the60/rules.mk b/keyboards/lazydesigners/the60/rules.mk index 76fb44b2c..97ea15d34 100644 --- a/keyboards/lazydesigners/the60/rules.mk +++ b/keyboards/lazydesigners/the60/rules.mk @@ -1,41 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/lets_split/keymaps/default/rules.mk b/keyboards/lets_split/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/lets_split/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/lets_split/rev1/rules.mk b/keyboards/lets_split/rev1/rules.mk index f84561674..e69de29bb 100644 --- a/keyboards/lets_split/rev1/rules.mk +++ b/keyboards/lets_split/rev1/rules.mk @@ -1 +0,0 @@ -BACKLIGHT_ENABLE = no
\ No newline at end of file diff --git a/keyboards/lets_split/rev2/rules.mk b/keyboards/lets_split/rev2/rules.mk index 7b30c0bef..e69de29bb 100644 --- a/keyboards/lets_split/rev2/rules.mk +++ b/keyboards/lets_split/rev2/rules.mk @@ -1 +0,0 @@ -BACKLIGHT_ENABLE = no diff --git a/keyboards/lets_split/rules.mk b/keyboards/lets_split/rules.mk index 489965735..98736310c 100644 --- a/keyboards/lets_split/rules.mk +++ b/keyboards/lets_split/rules.mk @@ -1,50 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/lets_split_eh/eh/rules.mk b/keyboards/lets_split_eh/eh/rules.mk index c0f8760d8..31077066a 100644 --- a/keyboards/lets_split_eh/eh/rules.mk +++ b/keyboards/lets_split_eh/eh/rules.mk @@ -1,4 +1,2 @@ -BOOTLOADER = atmel-dfu - BACKLIGHT_ENABLE = yes RGBLIGHT_ENABLE = yes diff --git a/keyboards/lets_split_eh/keymaps/default/rules.mk b/keyboards/lets_split_eh/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/lets_split_eh/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/lets_split_eh/rules.mk b/keyboards/lets_split_eh/rules.mk index 27661cebb..2bcd087d8 100644 --- a/keyboards/lets_split_eh/rules.mk +++ b/keyboards/lets_split_eh/rules.mk @@ -1,48 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/lfkeyboards/lfk65_hs/keymaps/default/rules.mk b/keyboards/lfkeyboards/lfk65_hs/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/lfkeyboards/lfk65_hs/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/lfkeyboards/lfk65_hs/rules.mk b/keyboards/lfkeyboards/lfk65_hs/rules.mk index 5118c3597..bfae80e0c 100644 --- a/keyboards/lfkeyboards/lfk65_hs/rules.mk +++ b/keyboards/lfkeyboards/lfk65_hs/rules.mk @@ -6,15 +6,3 @@ BOOT_LOADER = BootloaderHID # Extra source files for IS3731 lighting SRC = TWIlib.c issi.c lighting.c - -# Processor frequency. -F_CPU = 16000000 - -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT diff --git a/keyboards/lfkeyboards/lfkpad/rules.mk b/keyboards/lfkeyboards/lfkpad/rules.mk index 83553f64c..7ed840ae9 100644 --- a/keyboards/lfkeyboards/lfkpad/rules.mk +++ b/keyboards/lfkeyboards/lfkpad/rules.mk @@ -1,14 +1,15 @@ -SRC = TWIlib.c issi.c lighting.c - +# MCU name MCU = atmega32u4 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 -F_CPU = 16000000 -F_USB = $(F_CPU) -ARCH = AVR8 - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu LAYOUTS = numpad_6x4 @@ -31,6 +32,7 @@ TAP_DANCE_ENABLE = no ISSI_ENABLE = yes # If the I2C pullup resistors aren't install this must be disabled WATCHDOG_ENABLE = no # Resets keyboard if matrix_scan isn't run every 250ms +SRC = TWIlib.c issi.c lighting.c ifeq ($(strip $(ISSI_ENABLE)), yes) TMK_COMMON_DEFS += -DISSI_ENABLE diff --git a/keyboards/lily58/rev1/rules.mk b/keyboards/lily58/rev1/rules.mk index 7fc101bf2..6028b5a5b 100644 --- a/keyboards/lily58/rev1/rules.mk +++ b/keyboards/lily58/rev1/rules.mk @@ -1,3 +1,3 @@ SRC += rev1/matrix.c SRC += rev1/split_util.c -SRC += rev1/split_scomm.c
\ No newline at end of file +SRC += rev1/split_scomm.c diff --git a/keyboards/lily58/rules.mk b/keyboards/lily58/rules.mk index d13c88ba6..af25531ec 100644 --- a/keyboards/lily58/rules.mk +++ b/keyboards/lily58/rules.mk @@ -1,57 +1,16 @@ -SRC += i2c.c -SRC += serial.c -SRC += ssd1306.c - -# if firmware size over limit, try this option -# CFLAGS += -flto - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -73,4 +32,11 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend CUSTOM_MATRIX = yes +SRC += i2c.c +SRC += serial.c +SRC += ssd1306.c + +# if firmware size over limit, try this option +# CFLAGS += -flto + DEFAULT_FOLDER = lily58/rev1 diff --git a/keyboards/m10a/keymaps/default/rules.mk b/keyboards/m10a/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/m10a/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/m10a/rules.mk b/keyboards/m10a/rules.mk index 905babacb..739e396df 100644 --- a/keyboards/m10a/rules.mk +++ b/keyboards/m10a/rules.mk @@ -1,49 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/maartenwut/atom47/rev2/rules.mk b/keyboards/maartenwut/atom47/rev2/rules.mk index a3a258ed8..24d1c4199 100644 --- a/keyboards/maartenwut/atom47/rev2/rules.mk +++ b/keyboards/maartenwut/atom47/rev2/rules.mk @@ -1,3 +1,2 @@ - NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) diff --git a/keyboards/maartenwut/atom47/rules.mk b/keyboards/maartenwut/atom47/rules.mk index 39bfbc2b0..0728c1a28 100644 --- a/keyboards/maartenwut/atom47/rules.mk +++ b/keyboards/maartenwut/atom47/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 -BOOTLOADER= qmk-dfu +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = qmk-dfu # Build Options # comment out to disable the options. @@ -62,4 +26,3 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID DEFAULT_FOLDER = maartenwut/atom47/rev3 - diff --git a/keyboards/maartenwut/plain60/keymaps/via/rules.mk b/keyboards/maartenwut/plain60/keymaps/via/rules.mk index 0ccefbb11..2b23b188b 100644 --- a/keyboards/maartenwut/plain60/keymaps/via/rules.mk +++ b/keyboards/maartenwut/plain60/keymaps/via/rules.mk @@ -3,4 +3,3 @@ SRC += keyboards/wilba_tech/wt_main.c RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes - diff --git a/keyboards/maartenwut/plain60/rules.mk b/keyboards/maartenwut/plain60/rules.mk index aad559846..77b5a3eb9 100644 --- a/keyboards/maartenwut/plain60/rules.mk +++ b/keyboards/maartenwut/plain60/rules.mk @@ -1,50 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = qmk-dfu # Build Options # comment out to disable the options. @@ -63,4 +28,3 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID LAYOUTS = 60_ansi 60_ansi_split_bs_rshift 60_hhkb 60_iso 60_tsangan_hhkb - diff --git a/keyboards/maartenwut/ta65/rules.mk b/keyboards/maartenwut/ta65/rules.mk index 47207cd46..ecc629698 100644 --- a/keyboards/maartenwut/ta65/rules.mk +++ b/keyboards/maartenwut/ta65/rules.mk @@ -1,49 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = qmk-dfu # Build Options diff --git a/keyboards/maartenwut/wasdat/rules.mk b/keyboards/maartenwut/wasdat/rules.mk index c9deae5c5..059e84a1a 100644 --- a/keyboards/maartenwut/wasdat/rules.mk +++ b/keyboards/maartenwut/wasdat/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = qmk-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/maartenwut/wonderland/rules.mk b/keyboards/maartenwut/wonderland/rules.mk index 498076d4e..19c0ea591 100755 --- a/keyboards/maartenwut/wonderland/rules.mk +++ b/keyboards/maartenwut/wonderland/rules.mk @@ -1,42 +1,14 @@ +# MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = qmk-dfu # Build Options diff --git a/keyboards/maxipad/promicro/rules.mk b/keyboards/maxipad/promicro/rules.mk index dc6f19623..e6fef5172 100644 --- a/keyboards/maxipad/promicro/rules.mk +++ b/keyboards/maxipad/promicro/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/maxipad/teensy2/rules.mk b/keyboards/maxipad/teensy2/rules.mk index 3fb7c7e5a..ae398e258 100644 --- a/keyboards/maxipad/teensy2/rules.mk +++ b/keyboards/maxipad/teensy2/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/maxr1998/phoebe/keymaps/default/rules.mk b/keyboards/maxr1998/phoebe/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/maxr1998/phoebe/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/maxr1998/phoebe/rules.mk b/keyboards/maxr1998/phoebe/rules.mk index 1f2724737..b73145d7f 100644 --- a/keyboards/maxr1998/phoebe/rules.mk +++ b/keyboards/maxr1998/phoebe/rules.mk @@ -1,10 +1,14 @@ # MCU name MCU = atmega32u4 -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options @@ -27,4 +31,3 @@ RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. KEY_LOCK_ENABLE = yes API_SYSEX_ENABLE = no SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - diff --git a/keyboards/maxr1998/pulse4k/keymaps/default/rules.mk b/keyboards/maxr1998/pulse4k/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb..000000000 --- a/keyboards/maxr1998/pulse4k/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/maxr1998/pulse4k/rules.mk b/keyboards/maxr1998/pulse4k/rules.mk index 644666221..cee105352 100644 --- a/keyboards/maxr1998/pulse4k/rules.mk +++ b/keyboards/maxr1998/pulse4k/rules.mk @@ -1,15 +1,16 @@ # MCU name MCU = atmega32u4 -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -30,4 +31,3 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. API_SYSEX_ENABLE = no SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - diff --git a/keyboards/mechkeys/mk60/rules.mk b/keyboards/mechkeys/mk60/rules.mk index f1513f299..4f8bd49ef 100644 --- a/keyboards/mechkeys/mk60/rules.mk +++ b/keyboards/mechkeys/mk60/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/mechllama/g35/rules.mk b/keyboards/mechllama/g35/rules.mk index 1e1487513..20fbf160a 100644 --- a/keyboards/mechllama/g35/rules.mk +++ b/keyboards/mechllama/g35/rules.mk @@ -1,10 +1,14 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) - -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu NKRO_ENABLE = yes diff --git a/keyboards/mechmini/v2/rules.mk b/keyboards/mechmini/v2/rules.mk index f9ef6414b..72d307322 100755 --- a/keyboards/mechmini/v2/rules.mk +++ b/keyboards/mechmini/v2/rules.mk @@ -1,53 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # comment out to disable the options. # diff --git a/keyboards/meira/featherble/rules.mk b/keyboards/meira/featherble/rules.mk index e27608983..b0295ced7 100644 --- a/keyboards/meira/featherble/rules.mk +++ b/keyboards/meira/featherble/rules.mk @@ -1,3 +1,5 @@ -BLUETOOTH_ENABLE = yes +# Processor frequency F_CPU = 8000000 + +BLUETOOTH_ENABLE = yes BLUETOOTH = AdafruitBLE diff --git a/keyboards/meira/promicro/rules.mk b/keyboards/meira/promicro/rules.mk index 22e49971f..3c81f1b34 100644 --- a/keyboards/meira/promicro/rules.mk +++ b/keyboards/meira/promicro/rules.mk @@ -1,14 +1 @@ -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - BLUETOOTH_ENABLE = no diff --git a/keyboards/meira/rules.mk b/keyboards/meira/rules.mk index 7893e6556..8357e780b 100644 --- a/keyboards/meira/rules.mk +++ b/keyboards/meira/rules.mk @@ -1,44 +1,14 @@ -SRC += matrix.c TWIlib.c issi.c lighting.c - # MCU name MCU = atmega32u4 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -BOOTLOADER = caterina - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Build Options @@ -72,6 +42,7 @@ CUSTOM_MATRIX = yes #ifeq ($(strip $(WATCHDOG_ENABLE)), yes) # TMK_COMMON_DEFS += -DWATCHDOG_ENABLE #endif +SRC += matrix.c TWIlib.c issi.c lighting.c DEFAULT_FOLDER = meira/promicro LAYOUTS = ortho_4x12 diff --git a/keyboards/meishi/rules.mk b/keyboards/meishi/rules.mk index 6cba6b6b8..571a1c48c 100644 --- a/keyboards/meishi/rules.mk +++ b/keyboards/meishi/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable diff --git a/keyboards/meishi2/rules.mk b/keyboards/meishi2/rules.mk index bc370be03..7218e1e1b 100644 --- a/keyboards/meishi2/rules.mk +++ b/keyboards/meishi2/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/melody96/rules.mk b/keyboards/melody96/rules.mk index be0f84b17..1e6d4bb7c 100644 --- a/keyboards/melody96/rules.mk +++ b/keyboards/melody96/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # comment out to disable the options. # diff --git a/keyboards/meson/rules.mk b/keyboards/meson/rules.mk index 4b585e829..323ec666a 100644 --- a/keyboards/meson/rules.mk +++ b/keyboards/meson/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/miniaxe/keymaps/underglow/rules.mk b/keyboards/miniaxe/keymaps/underglow/rules.mk index 64fa91ded..1e3cebb14 100644 --- a/keyboards/miniaxe/keymaps/underglow/rules.mk +++ b/keyboards/miniaxe/keymaps/underglow/rules.mk @@ -1,2 +1 @@ -RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow - +RGBLIGHT_ENABLE = yes diff --git a/keyboards/miniaxe/rules.mk b/keyboards/miniaxe/rules.mk index 3f5f699ff..204aeed76 100644 --- a/keyboards/miniaxe/rules.mk +++ b/keyboards/miniaxe/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # @@ -82,4 +35,3 @@ HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) DEBUG_ENABLE = no CUSTOM_MATRIX = no # Use custom matrix code SPLIT_KEYBOARD = yes # Use shared split_common code - diff --git a/keyboards/minidox/rev1/rules.mk b/keyboards/minidox/rev1/rules.mk index f84561674..7b30c0bef 100644 --- a/keyboards/minidox/rev1/rules.mk +++ b/keyboards/minidox/rev1/rules.mk @@ -1 +1 @@ -BACKLIGHT_ENABLE = no
\ No newline at end of file +BACKLIGHT_ENABLE = no diff --git a/keyboards/minidox/rules.mk b/keyboards/minidox/rules.mk index bcd74bcde..dd2affb3f 100644 --- a/keyboards/minidox/rules.mk +++ b/keyboards/minidox/rules.mk @@ -1,52 +1,16 @@ -SRC += matrix.c \ - i2c.c \ - split_util.c \ - serial.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -68,5 +32,9 @@ USE_I2C ?= no SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend CUSTOM_MATRIX = yes +SRC += matrix.c \ + i2c.c \ + split_util.c \ + serial.c DEFAULT_FOLDER = minidox/rev1 diff --git a/keyboards/mint60/rules.mk b/keyboards/mint60/rules.mk index 21efa65cf..037e81431 100644 --- a/keyboards/mint60/rules.mk +++ b/keyboards/mint60/rules.mk @@ -1,56 +1,15 @@ -SRC += i2c.c \ - serial.c \ - matrix.c \ - split_util.c \ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable @@ -73,5 +32,9 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) CUSTOM_MATRIX = yes +SRC += i2c.c \ + serial.c \ + matrix.c \ + split_util.c USE_I2C = yes RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. diff --git a/keyboards/mitosis/rules.mk b/keyboards/mitosis/rules.mk index 34aa7070f..420c49f9b 100644 --- a/keyboards/mitosis/rules.mk +++ b/keyboards/mitosis/rules.mk @@ -1,56 +1,16 @@ - -OPT_DEFS += -DMITOSIS_PROMICRO -MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - -# # project specific files -SRC = matrix.c - - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # comment out to disable the options. # @@ -72,3 +32,10 @@ USB = /dev/ttyACM0 # upload: build # $(MITOSIS_UPLOAD_COMMAND) + +OPT_DEFS += -DMITOSIS_PROMICRO +MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) + +# # project specific files +SRC = matrix.c diff --git a/keyboards/miuni32/keymaps/default/rules.mk b/keyboards/miuni32/keymaps/default/rules.mk deleted file mode 100644 index 3a741d20a..000000000 --- a/keyboards/miuni32/keymaps/default/rules.mk +++ /dev/null @@ -1,18 +0,0 @@ -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - diff --git a/keyboards/miuni32/rules.mk b/keyboards/miuni32/rules.mk index 91cb2221e..68622e672 100644 --- a/keyboards/miuni32/rules.mk +++ b/keyboards/miuni32/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable @@ -53,14 +17,15 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096 BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) +CONSOLE_ENABLE = no # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = no # USB Nkey Rollover +NKRO_ENABLE = yes # USB Nkey Rollover BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 +RGBLIGHT_ENABLE = yes diff --git a/keyboards/model01/keymaps/default/rules.mk b/keyboards/model01/keymaps/default/rules.mk deleted file mode 100644 index 4d1abd88a..000000000 --- a/keyboards/model01/keymaps/default/rules.mk +++ /dev/null @@ -1,2 +0,0 @@ -# used by default keymap -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) diff --git a/keyboards/model01/rules.mk b/keyboards/model01/rules.mk index 4345027f4..5e3cbaa33 100644 --- a/keyboards/model01/rules.mk +++ b/keyboards/model01/rules.mk @@ -1,53 +1,21 @@ -QUANTUM_LIB_SRC += i2c_master.c -SRC += leds.c \ - matrix.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Build Options # change yes to no to disable # BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = yes # Console for debug(+400) COMMAND_ENABLE = no # Commands for debug and configuration @@ -59,6 +27,9 @@ MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) UNICODE_ENABLE = no # Unicode CUSTOM_MATRIX = yes +QUANTUM_LIB_SRC += i2c_master.c +SRC += leds.c \ + matrix.c # You can set RGB_MATRIX_ENABLE = no in your rules.mk to disable this and save the Flash RGB_MATRIX_ENABLE = custom # Enable RGB matrix effects (+10000). diff --git a/keyboards/moon/rules.mk b/keyboards/moon/rules.mk index c8b39e8b7..3c67b3c28 100644 --- a/keyboards/moon/rules.mk +++ b/keyboards/moon/rules.mk @@ -1,50 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/mt980/rules.mk b/keyboards/mt980/rules.mk index 9a7718aad..b3655bf72 100644 --- a/keyboards/mt980/rules.mk +++ b/keyboards/mt980/rules.mk @@ -1,47 +1,19 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options # comment out to disable the options. # - BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = no # Mouse keys(+4700) EXTRAKEY_ENABLE = no # Audio control and System control(+450) diff --git a/keyboards/mxss/rules.mk b/keyboards/mxss/rules.mk index ac7a1ee8f..7df851758 100644 --- a/keyboards/mxss/rules.mk +++ b/keyboards/mxss/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable |