diff options
author | fauxpark <fauxpark@gmail.com> | 2019-10-13 09:57:57 +1100 |
---|---|---|
committer | Joel Challis <git@zvecr.com> | 2019-10-12 23:57:57 +0100 |
commit | 2e7cd98c0644dc0f7f2a5cab5da7b0e019bd0810 (patch) | |
tree | c72effd7d9fa349e2956ffa50747bf3d9ff301f9 /keyboards | |
parent | a48468590ab83e808191c0e20c236d7eb6c13f0d (diff) | |
download | firmware-2e7cd98c0644dc0f7f2a5cab5da7b0e019bd0810.tar.gz firmware-2e7cd98c0644dc0f7f2a5cab5da7b0e019bd0810.tar.bz2 firmware-2e7cd98c0644dc0f7f2a5cab5da7b0e019bd0810.zip |
Cleanup rules.mk for 32U4 keyboards, G (#6971)
* Cleanup rules.mk for 32U4 keyboards, G
* Update keyboards/gray_studio/cod67/rules.mk
Diffstat (limited to 'keyboards')
-rw-r--r-- | keyboards/angel17/alpha/rules.mk | 15 | ||||
-rw-r--r-- | keyboards/angel17/rev1/rules.mk | 15 | ||||
-rw-r--r-- | keyboards/clueboard/card/rules.mk | 1 | ||||
-rw-r--r-- | keyboards/duck/orion/v3/rules.mk | 3 | ||||
-rw-r--r-- | keyboards/fc660c/rules.mk | 1 | ||||
-rw-r--r-- | keyboards/geekboards/tester/rules.mk | 52 | ||||
-rw-r--r-- | keyboards/georgi/rules.mk | 26 | ||||
-rw-r--r-- | keyboards/gergo/rules.mk | 25 | ||||
-rw-r--r-- | keyboards/gh60/revc/rules.mk | 54 | ||||
-rw-r--r-- | keyboards/gh60/satan/rules.mk | 51 | ||||
-rw-r--r-- | keyboards/gh80_3000/rules.mk | 48 | ||||
-rw-r--r-- | keyboards/gonnerd/rules.mk | 53 | ||||
-rw-r--r-- | keyboards/gray_studio/cod67/rules.mk | 54 | ||||
-rw-r--r-- | keyboards/gray_studio/space65/rules.mk | 53 | ||||
-rw-r--r-- | keyboards/grid600/press/rules.mk | 51 | ||||
-rwxr-xr-x | keyboards/gskt00/rules.mk | 43 |
16 files changed, 97 insertions, 448 deletions
diff --git a/keyboards/angel17/alpha/rules.mk b/keyboards/angel17/alpha/rules.mk index 423ebddc5..5a26a2e0b 100644 --- a/keyboards/angel17/alpha/rules.mk +++ b/keyboards/angel17/alpha/rules.mk @@ -1,27 +1,16 @@ # MCU name MCU = atmega32u4 - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/angel17/rev1/rules.mk b/keyboards/angel17/rev1/rules.mk index fe22b3ab8..c76c0244a 100644 --- a/keyboards/angel17/rev1/rules.mk +++ b/keyboards/angel17/rev1/rules.mk @@ -1,27 +1,16 @@ # MCU name MCU = atmega32u4 - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/clueboard/card/rules.mk b/keyboards/clueboard/card/rules.mk index 2162b25de..9e3f19dc0 100644 --- a/keyboards/clueboard/card/rules.mk +++ b/keyboards/clueboard/card/rules.mk @@ -11,7 +11,6 @@ MCU = atmega32u4 # ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) diff --git a/keyboards/duck/orion/v3/rules.mk b/keyboards/duck/orion/v3/rules.mk index a57b3d60c..c46cb7544 100644 --- a/keyboards/duck/orion/v3/rules.mk +++ b/keyboards/duck/orion/v3/rules.mk @@ -11,7 +11,6 @@ MCU = atmega32u4 # ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # change yes to no to disable # @@ -36,4 +35,4 @@ CUSTOM_MATRIX = yes SRC += indicator_leds.c \ matrix.c duck_led/duck_led.c -LAYOUTS = tkl_ansi
\ No newline at end of file +LAYOUTS = tkl_ansi diff --git a/keyboards/fc660c/rules.mk b/keyboards/fc660c/rules.mk index 18613a591..b817b404f 100644 --- a/keyboards/fc660c/rules.mk +++ b/keyboards/fc660c/rules.mk @@ -11,7 +11,6 @@ MCU = atmega32u4 # ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # comment out to disable the options. # diff --git a/keyboards/geekboards/tester/rules.mk b/keyboards/geekboards/tester/rules.mk index 7e8d595fb..1ca57f6d0 100644 --- a/keyboards/geekboards/tester/rules.mk +++ b/keyboards/geekboards/tester/rules.mk @@ -1,52 +1,16 @@ # MCU name MCU = atmega32u4 -# project specific files -#SRC = - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = qmk-dfu -# Do not put the microcontroller into power saving mode -# when we get USB suspend event. We want it to keep updating -# backlight effects. - # Build Options # change yes to no to disable # diff --git a/keyboards/georgi/rules.mk b/keyboards/georgi/rules.mk index a87b448e3..412a318f0 100644 --- a/keyboards/georgi/rules.mk +++ b/keyboards/georgi/rules.mk @@ -1,18 +1,15 @@ -#---------------------------------------------------------------------------- -# make georgi:default:dfu -# Make sure you have dfu-programmer installed! -# Do not edit this file! Make a copy of keymaps/default and modify that! -#---------------------------------------------------------------------------- -# Source includes -SRC += matrix.c i2c_master.c sten.c - -# Hardware info +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu -F_USB = $(F_CPU) -EXTRAFLAGS += -flto CUSTOM_MATRIX = yes MOUSEKEY_ENABLE = no @@ -21,3 +18,6 @@ EXTRAKEY_ENABLE = yes CONSOLE_ENABLE = yes COMMAND_ENABLE = no NKRO_ENABLE = yes + +EXTRAFLAGS += -flto +SRC += matrix.c i2c_master.c sten.c diff --git a/keyboards/gergo/rules.mk b/keyboards/gergo/rules.mk index 2b5d62988..41f201a45 100644 --- a/keyboards/gergo/rules.mk +++ b/keyboards/gergo/rules.mk @@ -1,18 +1,15 @@ -#---------------------------------------------------------------------------- -# make gergo:germ:dfu -# Make sure you have dfu-programmer installed! -# Do not edit this file! Make a copy of keymaps/default and modify that! -#---------------------------------------------------------------------------- -# Source includes -SRC += matrix.c -QUANTUM_LIB_SRC += i2c_master.c - -# Hardware info +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu -F_USB = $(F_CPU) CUSTOM_MATRIX = yes EXTRAKEY_ENABLE = yes @@ -21,3 +18,5 @@ COMMAND_ENABLE = yes BOOTMAGIC_ENABLE = lite DEBOUNCE_TYPE = eager_pr +SRC += matrix.c +QUANTUM_LIB_SRC += i2c_master.c diff --git a/keyboards/gh60/revc/rules.mk b/keyboards/gh60/revc/rules.mk index bf7ea514d..c9362b334 100644 --- a/keyboards/gh60/revc/rules.mk +++ b/keyboards/gh60/revc/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # comment out to disable the options. diff --git a/keyboards/gh60/satan/rules.mk b/keyboards/gh60/satan/rules.mk index b6bb68391..9bd667535 100644 --- a/keyboards/gh60/satan/rules.mk +++ b/keyboards/gh60/satan/rules.mk @@ -1,48 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # comment out to disable the options. diff --git a/keyboards/gh80_3000/rules.mk b/keyboards/gh80_3000/rules.mk index 9e4bc3f0d..0da2d6a2f 100644 --- a/keyboards/gh80_3000/rules.mk +++ b/keyboards/gh80_3000/rules.mk @@ -1,45 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # comment out to disable the options. diff --git a/keyboards/gonnerd/rules.mk b/keyboards/gonnerd/rules.mk index ebea1005b..d4858ff13 100644 --- a/keyboards/gonnerd/rules.mk +++ b/keyboards/gonnerd/rules.mk @@ -1,51 +1,18 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. +# Processor frequency F_CPU = 8000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable diff --git a/keyboards/gray_studio/cod67/rules.mk b/keyboards/gray_studio/cod67/rules.mk index 6cba6b6b8..1df4615eb 100644 --- a/keyboards/gray_studio/cod67/rules.mk +++ b/keyboards/gray_studio/cod67/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = lufa-ms # Build Options # change yes to no to disable diff --git a/keyboards/gray_studio/space65/rules.mk b/keyboards/gray_studio/space65/rules.mk index 261569206..ced89eac0 100644 --- a/keyboards/gray_studio/space65/rules.mk +++ b/keyboards/gray_studio/space65/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # @@ -79,4 +32,4 @@ AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) -LAYOUTS = 65_ansi_blocker
\ No newline at end of file +LAYOUTS = 65_ansi_blocker diff --git a/keyboards/grid600/press/rules.mk b/keyboards/grid600/press/rules.mk index 1fcf3841b..fb575b3ab 100644 --- a/keyboards/grid600/press/rules.mk +++ b/keyboards/grid600/press/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/gskt00/rules.mk b/keyboards/gskt00/rules.mk index 338384e3e..2acbeaa90 100755 --- a/keyboards/gskt00/rules.mk +++ b/keyboards/gskt00/rules.mk @@ -1,41 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options |