Update Atreus to current code conventions (#5849)

* Update atreus to current code conventions - add multi revision instead of defines

* Remove config.h duplication from user keymaps

* Add breaking change log

* Add missing pragma once

1 files changed, 5 insertions, 71 deletions

diff --git a/keyboards/atreus/rules.mk b/keyboards/atreus/rules.mk
index eda77404a..403b0b0ca 100644
--- a/keyboards/atreus/rules.mk
+++ b/keyboards/atreus/rules.mk
@@ -1,75 +1,7 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
-ifdef TEENSY2
-    BOOTLOADER = halfkay
-    OPT_DEFS += -DATREUS_TEENSY2
-else
-    BOOTLOADER = caterina
-    OPT_DEFS += -DATREUS_ASTAR
-    ifdef PCBDOWN
-        OPT_DEFS += -DPCBDOWN
-    endif
-endif
-
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = yes        # Console for debug(+400)
@@ -77,12 +9,14 @@ COMMAND_ENABLE = yes        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
+NKRO_ENABLE = yes           # USB Nkey Rollover
 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = yes         # Unicode
+UNICODE_ENABLE = yes        # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+DEFAULT_FOLDER = atreus/astar