blob: d498f7991bea0d549aff60a4ff30ce09d934832e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
|
/*
ChibiOS - Copyright (C) 2006-2014 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file LPC214x/serial_lld.h
* @brief LPC214x low level serial driver header.
*
* @addtogroup SERIAL
* @{
*/
#ifndef _SERIAL_LLD_H_
#define _SERIAL_LLD_H_
#if HAL_USE_SERIAL || defined(__DOXYGEN__)
/*===========================================================================*/
/* Driver constants. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver pre-compile time settings. */
/*===========================================================================*/
/**
* @brief UART0 driver enable switch.
* @details If set to @p TRUE the support for UART0 is included.
* @note The default is @p TRUE .
*/
#if !defined(USE_LPC214x_UART0) || defined(__DOXYGEN__)
#define USE_LPC214x_UART0 TRUE
#endif
/**
* @brief UART1 driver enable switch.
* @details If set to @p TRUE the support for UART1 is included.
* @note The default is @p TRUE.
*/
#if !defined(USE_LPC214x_UART1) || defined(__DOXYGEN__)
#define USE_LPC214x_UART1 TRUE
#endif
/**
* @brief FIFO preload parameter.
* @details Configuration parameter, this values defines how many bytes are
* preloaded in the HW transmit FIFO for each interrupt, the maximum
* value is 16 the minimum is 1.
* @note An high value reduces the number of interrupts generated but can
* also increase the worst case interrupt response time because the
* preload loops.
*/
#if !defined(LPC214x_UART_FIFO_PRELOAD) || defined(__DOXYGEN__)
#define LPC214x_UART_FIFO_PRELOAD 16
#endif
/**
* @brief UART0 interrupt priority level setting.
*/
#if !defined(LPC214x_UART0_PRIORITY) || defined(__DOXYGEN__)
#define LPC214x_UART0_PRIORITY 1
#endif
/**
* @brief UART1 interrupt priority level setting.
*/
#if !defined(LPC214x_UART1_PRIORITY) || defined(__DOXYGEN__)
#define LPC214x_UART1_PRIORITY 2
#endif
/*===========================================================================*/
/* Derived constants and error checks. */
/*===========================================================================*/
#if (LPC214x_UART_FIFO_PRELOAD < 1) || (LPC214x_UART_FIFO_PRELOAD > 16)
#error "invalid LPC214x_UART_FIFO_PRELOAD setting"
#endif
/*===========================================================================*/
/* Driver data structures and types. */
/*===========================================================================*/
/**
* @brief LPC214x Serial Driver configuration structure.
* @details An instance of this structure must be passed to @p sdStart()
* in order to configure and start a serial driver operations.
*/
typedef struct {
/**
* @brief Bit rate.
*/
uint32_t sc_speed;
/**
* @brief Initialization value for the LCR register.
*/
uint32_t sc_lcr;
/**
* @brief Initialization value for the FCR register.
*/
uint32_t sc_fcr;
} SerialConfig;
/**
* @brief @p SerialDriver specific data.
*/
#define _serial_driver_data \
_base_asynchronous_channel_data \
/* Driver state.*/ \
sdstate_t state; \
/* Input queue.*/ \
input_queue_t iqueue; \
/* Output queue.*/ \
output_queue_t oqueue; \
/* Input circular buffer.*/ \
uint8_t ib[SERIAL_BUFFERS_SIZE]; \
/* Output circular buffer.*/ \
uint8_t ob[SERIAL_BUFFERS_SIZE]; \
/* End of the mandatory fields.*/ \
/* Pointer to the USART registers block.*/ \
UART *uart;
/*===========================================================================*/
/* Driver macros. */
/*===========================================================================*/
/*===========================================================================*/
/* External declarations. */
/*===========================================================================*/
#if USE_LPC214x_UART0 && !defined(__DOXYGEN__)
extern SerialDriver SD1;
#endif
#if USE_LPC214x_UART1 && !defined(__DOXYGEN__)
extern SerialDriver SD2;
#endif
#ifdef __cplusplus
extern "C" {
#endif
void sd_lld_init(void);
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config);
void sd_lld_stop(SerialDriver *sdp);
#ifdef __cplusplus
}
#endif
#endif /* HAL_USE_SERIAL */
#endif /* _SERIAL_LLD_H_ */
/** @} */
|