blob: 9dfca2262d94d86c4805021fb60ccee34f1f6daf (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
|
/*
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file STM8S/serial_lld.h
* @brief STM8S low level serial driver header.
*
* @addtogroup SERIAL
* @{
*/
#ifndef _SERIAL_LLD_H_
#define _SERIAL_LLD_H_
#if HAL_USE_SERIAL || defined(__DOXYGEN__)
/*===========================================================================*/
/* Driver constants. */
/*===========================================================================*/
#define SD_MODE_PARITY 0x07 /**< @brief Parity field mask. */
#define SD_MODE_PARITY_NONE 0x00 /**< @brief No parity. */
#define SD_MODE_PARITY_EVEN 0x05 /**< @brief Even parity. */
#define SD_MODE_PARITY_ODD 0x07 /**< @brief Odd parity. */
#define SD_MODE_STOP 0x30 /**< @brief Stop bits mask. */
#define SD_MODE_STOP_1 0x00 /**< @brief One stop bit. */
#define SD_MODE_STOP_2 0x20 /**< @brief Two stop bits. */
#define SD_MODE_STOP_1P5 0x30 /**< @brief 1.5 stop bits. */
/*===========================================================================*/
/* Driver pre-compile time settings. */
/*===========================================================================*/
/**
* @brief UART1 driver enable switch.
* @details If set to @p TRUE the support for UART1 is included.
* @note The default is @p TRUE.
*/
#if !defined(STM8S_SERIAL_USE_UART1) || defined(__DOXYGEN__)
#define STM8S_SERIAL_USE_UART1 TRUE
#endif
/**
* @brief UART2 driver enable switch.
* @details If set to @p TRUE the support for UART3 is included.
* @note The default is @p TRUE.
*/
#if !defined(STM8S_SERIAL_USE_UART2) || defined(__DOXYGEN__)
#define STM8S_SERIAL_USE_UART2 TRUE
#endif
/**
* @brief UART3 driver enable switch.
* @details If set to @p TRUE the support for UART3 is included.
* @note The default is @p TRUE.
*/
#if !defined(STM8S_SERIAL_USE_UART3) || defined(__DOXYGEN__)
#define STM8S_SERIAL_USE_UART3 TRUE
#endif
/*===========================================================================*/
/* Derived constants and error checks. */
/*===========================================================================*/
#if STM8S_SERIAL_USE_UART2 && STM8S_SERIAL_USE_UART3
#error "STM8S UART2 and UART3 cannot be used together"
#endif
/*===========================================================================*/
/* Driver data structures and types. */
/*===========================================================================*/
/**
* @brief Generic Serial Driver configuration structure.
* @details An instance of this structure must be passed to @p sdStart()
* in order to configure and start a serial driver operations.
* @note This structure content is architecture dependent, each driver
* implementation defines its own version and the custom static
* initializers.
*/
typedef struct {
/**
* @brief Bit rate register.
*/
uint16_t sc_brr;
/**
* @brief Mode flags.
*/
uint8_t sc_mode;
} SerialConfig;
/**
* @brief @p SerialDriver specific data.
*/
#define _serial_driver_data \
_base_asynchronous_channel_data \
/* Driver state.*/ \
sdstate_t state; \
/* Input queue.*/ \
InputQueue iqueue; \
/* Output queue.*/ \
OutputQueue oqueue; \
/* Input circular buffer.*/ \
uint8_t ib[SERIAL_BUFFERS_SIZE]; \
/* Output circular buffer.*/ \
uint8_t ob[SERIAL_BUFFERS_SIZE]; \
/* End of the mandatory fields.*/
/*===========================================================================*/
/* Driver macros. */
/*===========================================================================*/
/**
* @brief Macro for baud rate computation.
* @note Make sure the final baud rate is within tolerance.
*/
#define BRR(b) (SYSCLK / (b))
/*===========================================================================*/
/* External declarations. */
/*===========================================================================*/
#if STM8S_SERIAL_USE_UART1 && !defined(__DOXYGEN__)
extern SerialDriver SD1;
#endif
#if STM8S_SERIAL_USE_UART2 && !defined(__DOXYGEN__)
extern SerialDriver SD2;
#endif
#if STM8S_SERIAL_USE_UART3 && !defined(__DOXYGEN__)
extern SerialDriver SD3;
#endif
#ifdef __cplusplus
extern "C" {
#endif
void sd_lld_init(void);
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config);
void sd_lld_stop(SerialDriver *sdp);
#ifdef __cplusplus
}
#endif
#endif /* HAL_USE_SERIAL */
#endif /* _SERIAL_LLD_H_ */
/** @} */
|
