1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
|
/*
ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the Olimex STM32-P107 Rev.A evaluation board.
*/
/*
* Board identifier.
*/
#define BOARD_OLIMEX_STM32_P107_REV_A
#define BOARD_NAME "Olimex STM32-P107 Rev.A"
/*
* Board frequencies.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 25000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F107xC
/*
* Ethernet PHY type.
*/
#define BOARD_PHY_ID MII_STE101P_ID
#define BOARD_PHY_RMII
/*
* IO pins assignments.
*/
#define GPIOA_SWITCH_WKUP 0
#define GPIOA_SPI3_CS_MMC 4
#define GPIOC_LED_STATUS1 6
#define GPIOC_LED_STATUS2 7
#define GPIOC_SWITCH_TAMPER 13
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
* PA0 - Normal input (WKUP BUTTON).
* PA1 - Normal input (ETH_RMII_REF_CLK).
* PA2 - Alternate output (ETH_RMII_MDIO).
* PA3 - Input with PU (unconnected).
* PA4 - Open Drain output (CS_MMC).
* PA5 - Input with PU (unconnected).
* PA6 - Input with PU (unconnected).
* PA7 - Normal input (ETH_RMII_CRS_DV).
* PA8 - Alternate output (MCO).
* PA9 - Normal input (OTG_VBUS).
* PA10 - Normal input (OTG_ID).
* PA11 - Normal input (OTG_DM).
* PA12 - Normal input (OTG_DP).
* PA13 - Normal input (TMS).
* PA14 - Normal input (TCK).
* PA15 - Normal input (TDI).
*/
#define VAL_GPIOACRL 0x48878B44 /* PA7...PA0 */
#define VAL_GPIOACRH 0x4444444B /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup:
* PB0 - Input with PU (unconnected).
* PB1 - Input with PU (unconnected).
* PB2 - Normal input (BOOT1).
* PB3 - Normal input (TDO).
* PB4 - Normal input (TRST).
* PB5 - Input with PU (unconnected).
* PB6 - Input with PU (unconnected).
* PB7 - Input with PU (unconnected).
* PB8 - Alternate O.D. (I2C1 SCL, remapped).
* PB9 - Alternate O.D. (I2C1 SDA, remapped).
* PB10 - Input with PU (unconnected).
* PB11 - Alternate output (ETH_RMII_TX_EN).
* PB12 - Alternate output (ETH_RMII_TXD0).
* PB13 - Alternate output (ETH_RMII_TXD1).
* PB14 - Input with PU (unconnected).
* PB15 - Push Pull output (CS_UEXT).
*/
#define VAL_GPIOBCRL 0x88844488 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x38BBB8FF /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup:
* PC0 - Input with PU (unconnected).
* PC1 - Alternate output (ETH_MDC).
* PC2 - Input with PU (unconnected).
* PC3 - Input with PU (unconnected).
* PC4 - Normal input (ETH_RMII_RXD0).
* PC5 - Normal input (ETH_RMII_RXD1).
* PC6 - Push Pull output (STAT1 green LED).
* PC7 - Push Pull output (STAT2 yellow LED).
* PC8 - Input with PU (unconnected).
* PC9 - Input with PU (unconnected).
* PC10 - Alternate output (SPI3 SCK).
* PC11 - Input with PU (SPI3 MISO).
* PC12 - Alternate output (SPI3 MOSI).
* PC13 - Normal input (TAMPER).
* PC14 - Normal input (OSC32 IN).
* PC15 - Normal input (OSC32 OUT).
*/
#define VAL_GPIOCCRL 0x334488B8 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x444B8B88 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFF3F
/*
* Port D setup:
* PD0 - Input with PU (unconnected).
* PD1 - Input with PU (unconnected).
* PD2 - Input with PU (unconnected).
* PD3 - Input with PU (unconnected).
* PD4 - Input with PU (unconnected).
* PD5 - Alternate output (USART2 TX, UEXT).
* PD6 - Input with PU (USART2 RX, UEXT).
* PD7 - Push Pull output (USB_VBUSON).
* PD8 - Alternate output (USART2 TX, remapped).
* PD9 - Normal input (USART2 RX, remapped).
* PD10 - Input with PU (unconnected).
* PD11 - Normal input (USART2 CTS, remapped).
* PD12 - Alternate output (USART2 RTS, remapped).
* PD13 - Input with PU (unconnected).
* PD14 - Input with PU (unconnected).
* PD15 - Input with PU (unconnected).
*/
#define VAL_GPIODCRL 0x38B88888 /* PD7...PD0 */
#define VAL_GPIODCRH 0x888B484B /* PD15...PD8 */
#define VAL_GPIODODR 0xFFFFFFFF
/*
* Port E setup.
* Everything input with pull-up except:
* PE14 - Normal input (ETH_RMII_MDINT).
* PE15 - Normal input (USB_FAULT).
*/
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
#define VAL_GPIOECRH 0x44888888 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
